0437177 JOHNSON ENGINE COVER ASSY., Jo.


0437177 ENGINE COVER ASSY., Jo. JOHNSON BJ3REDS, BJ4BREDS, J3REOD, J4REOD ENGINE
0437177 ENGINE COVER ASSY., Jo. JOHNSON
Rating:
103

Buy ENGINE COVER ASSY., Jo. 0437177 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

BRP JOHNSON entire parts catalog list:

BJ3REDS, SJ3REDS 1996
BJ4BREDS, BJ4BRLEDS, BJ4REDS, BJ4RLEDS, J4REDS, J4RLEDS, SJ4REDS, SJ4RLEDS 1996
J3REOD 1995
J4REOD, J4RLEOD 1995

Information:

1. Remove elbow (1) from the oil pump.2. Bend the lock down and remove the bolt and lock that hold the suction bell assembly to the oil pan plate. 3. Bend the locks down and remove bolts (3) and the locks that hold oil pump (4) in place. Remove oil pump (4).
The oil pump idler gear is free to fall when the oil pump is removed.
Install Oil Pump
This operation was done on an earlier machine. 1. Put oil pump (1) in position on the engine and install the locks and bolts (2) that hold the oil pump in place. Be sure the idler gear is engaged with the crankshaft gear before bolts (2) are tightened. 2. Install the bolt and lock that hold suction bell assembly (4) to the oil pan plate.3. Put the gasket in place and install elbow (3).end by: a) install oil panDisassemble Oil Pump
start by: a) remove oil pump 1. Remove idler gear (2). Remove bearing from gear with tooling (B) and a press.2. Remove suction bell (1).3. Remove the bolt and the washer from the oil pump drive gear. 4. Remove the drive gear from the shaft with tooling (A).5. Remove the key from the pump shaft.6. Remove bolts (3) from the pump body. 7. Remove body (8), two gears (7), keys and spacer (4) from the pump.8. Remove two shafts (5) and the gears.9. Remove bolts (6), the cover and the pressure relief valve from the body. 10. Remove the bearings from the oil pump body assembly and the scavenge pump body assembly with tooling (C).Assemble Oil Pump
1. Install the bearings in the scavenge pump body assembly with tooling (A) and a press as follows: a) Put bearings (1) in position on the inside of the scavenge pump body assembly with the chamfer on the bearing toward the outside of the pump body. Install the bearing until it is .060 in. (1.52 mm) below the inside machined surface of the scavenge pump body assembly. Make sure the joints in the bearings are at an angle of 30° 15° from the center line through the bores in the scavenge pump body and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores. 2. Install the bearings in oil pump body assembly with tooling (A) and a press as follows: a) Put bearings (2) in position on the inside of the oil pump body assembly with the chamfer on the bearings toward the outside of the pump body. Install the bearings until they are even with the outside of the pump body. Make sure the joints in the bearings are at an angle of 30° 15° from the centerline through the bearing bores and toward the outlet passage of the pump. The outlet passage has a cavity between the bearing bores.3. Check the condition of the relief valve. Check the condition and specifications for all the parts of the oil pump before it is assembled. See OIL PUMP in SPECIFICATIONS.4. Put clean engine oil on all the parts of the oil pump. 5. Install pressure relief valve (3), cover (4) and bolt (5) in the oil pump body assembly.6. Install gears and shafts (6) in the oil pump body assembly. 7. Install spacer (7) and the two keys in shafts (6). 8. Install two gears and scavenge pump body assembly (8).9. Install key (9), drive gear (11), the washer and bolt (10). Tighten the bolt to a torque of 32 5 lb.ft. (43 7 N m). 10. Install bearing (12) in idler gear (13) with tooling (B) and a press until it is even with the outside surface of the gear.11. Install idler gear (13) on the pump.12. Put the gasket and suction bell assembly (14) in position and install the locks and bolts (15) that hold it. Bend the locks up.
The oil pump must turn freely by hand after it is assembled.
end by: a) install oil pump


Parts engine JOHNSON:

0435136
 
0435136 ENGINE COVER ASSY., Jo.
BJ3REDS, BJ4BREDS, J3RENM, J3REOD, J3RERE, J3RETB, J4RENM, J4REOD, J4RERE, J4RETB
0435138
 
0435138 ENGINE COVER ASSY., Jo.
BJ3REDS, BJ4BREDS, J3RENM, J3REOD, J3RERE, J3RETB, J4RENM, J4REOD, J4RERE, J4RETB
0435137
 
0435137 ENGINE COVER ASSY., Jo.
BJ3REDS, BJ4BREDS, J3REOD, J4REOD
0284691
 
0284691 ENGINE COVER ASSY., Ev.
BJ3REDS, BJ4BREDS, BJ4BREUC, J3REOD, J3REUC, J4REOD
0284692
 
0284692 ENGINE COVER ASSY., Ev.
BJ3REDS, BJ4BREDS, BJ4BREUC, J3REOD, J3REUC, J4REOD
0284693
 
0284693 ENGINE COVER ASSY., Ev.
BJ3REDS, BJ4BREDS, BJ4BREUC, J3REOD, J3REUC, J4REOD
0437173
 
0437173 ENGINE COVER ASSY., Jo.
BJ3REDS, BJ4BREDS, J3REOD, J4REOD
0342188
 
0342188 ENGINE COVER, Lower, Jo., front
BJ3REDS, BJ4BREDS, J3REOD, J4REOD, J4RLSIB
Back to top