0437189 JOHNSON ENGINE COVER ASSY.


0437189 ENGINE COVER ASSY. JOHNSON BJ20SEEDA, BJ25EEDM, BJ30EEDE, HJ25TELEDA, J20EEOR, J25EEOA, J25TEEOR, J30EEOB, J30TEEDE, J30TEEOB ENGINE
0437189 ENGINE COVER ASSY. JOHNSON
Rating:
103

Buy ENGINE COVER ASSY. 0437189 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

BRP JOHNSON entire parts catalog list:

BJ20SEEDA, BJ20SELEDA 1996
BJ25EEDM, BJ25ELEDM, BJ25EREDC, BJ25ERLEDC, J25EEDM, J25ELEDM 1996
BJ30EEDE, BJ30ELEDE, J30EEDE, J30ELEDE, SJ30EEDE 1996
HJ25TELEDA, J25TEEDA, J25TELEDA, SJ25TEEDA 1996
J20EEOR, J20ELEOR 1995
J25EEOA, J25ELEOA 1995
J25TEEOR, J25TELEOR 1995
J30EEOB, J30ELEOB 1995
J30TEEDE, J30TELEDE 1996
J30TEEOB, J30TELEOB 1995

Information:

3. Put tool (A) in position in the cylinder liner. 4. Use tool (A) to loosen the cylinder liners from the cylinder block. 5. Remove cylinder liners (1) from the cylinder block. 6. Remove filler band (3) and O-ring seals (2) from the cylinder liners.7. Check the cylinder liners for wear or damage. "Use again" maximum bore diameter (when measured near upper end of the wear surface of the cylinder liner) is 5.405 in. (137.29 mm). See GUIDELINE FOR REUSABLE PARTS: PISTONS AND CYLINDER LINERS, Form No. SEBF8001.Install Cylinder Liners
1. Clean the cylinder liners and the liner bores in the cylinder block. 2. Install cylinder liners (1) in the cylinder block without the filler bands or O-ring seals. 3. Check the cylinder liner projection as follows:a) Install the 3/4"-16 NF bolts and 2F126 washers of tooling (A) on the spacer plate around each cylinder liner as shown. Tighten the bolts evenly in four steps.Step 1 Tighten to a torque of 10 lb.ft. (14 N m).Step 2 Tighten to a torque of 25 lb.ft. (35 N m).Step 3 Tighten to a torque of 50 lb.ft. (70 N m).Step 4 Tighten to a torque of 70 lb.ft. (95 N m). b) Put the adapter plate and one plate of tooling (A) on top of the liner and install the remainder of tooling (A). Be sure the crossbar is in position at the center of the liner. Tighten the bolts that hold tooling (A) evenly in four steps:Step 1 Tighten to a torque of 5 lb.ft. (7 N m).Step 2 Tighten to a torque of 15 lb.ft. (20 N m).Step 3 Tighten to a torque of 25 lb.ft. (35 N m).Step 4 Tighten to a torque of 50 lb.ft. (70 N m).c) Check to be sure the distance from the bottom edge of the bar to the top of the cylinder block is the same on both sides of the cylinder liner.d) Check the cylinder liner projection with tooling (B) at four locations around the cylinder liner.e) Liner projection must be .005 .003 in. (0.13 0.08 mm). Measurements on the same liner must not be different by more than .002 in. (0.05 mm). Average measurements between liners next to each other must not be different by more than .002 in. (0.05 mm). If the liner is turned in the bore it can make a difference in the liner projection. 4. If the liner projection is not .005 .003 in. (0.13 0.08 mm), check the thickness of the following parts: spacer plate, spacer plate gasket, and cylinder liner flange. The thickness of the spacer plate must be .338 .001 in. (8.59 0.03 mm). The thickness of the spacer plate gasket must be .008 .001 in. (0.20 0.03 mm). The thickness (2) of the cylinder liner flange must be .3500 .0008 in. (8.890 0.020 mm). The cylinder liner projection can be changed if a counterbore is made in the block to a minimum depth of .030 in. (0.76 mm) with a cylinder block counterboring tool. See SPECIAL INSTRUCTION, Form FM055228. Shims are available for the adjustment of the liner projection. See PROJECTION OF CYLINDER LINER in 3406 VEHICULAR ENGINE, TESTING AND ADJUSTING for the shim thickness and part number.5. Put a mark on the liner and block so the liner can be installed in the same position as it was removed.6. Remove tooling (A) and tool (B). Remove one liner. 7. Put liquid soap on O-ring seals, grooves of the liner and the bore of the cylinder block. Install O-ring seals (3) on the cylinder liner.8. Put filler band (4) in clean SAE 30 oil for a short time (dip). Install the filler band on the liner. 9. Install the liner immediately after the filler band is installed. Make sure the mark on the liner is in alignment with the mark on the block. Use tooling (C) to push the liner into position.10. Do Steps 6 through 9 for the remainder of the cylinder liners.end by:a) install pistons
Cylinder liner must be installed in the block immediately after the filler band is installed on the liner. The filler band gets larger after it has been put in oil and can be damaged when installed if there is a time delay in installation.


Parts engine JOHNSON:

0433392
ENGINE COVER, Lower
0433392 ENGINE COVER, Lower
BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ30EECS, BJ30EEDE, BJ30EEEC, BJ30EEUD, BJ30E
0435152
ENGINE COVER ASSY.
0435152 ENGINE COVER ASSY.
BJ20SEEDA, BJ25EEDM, BJ30EEDE, HJ25TELEDA, J20EEND, J20EEOR, J20EERC, J20EETS, J25EENS, J25EEOA, J25EERR, J25EETC, J25TEEND, J25TEEOR, J25TEERC, J25TEETS, J25TELERC, J30EENR, J30EEOB, J30EERM, J30EETA, J30TEEDE, J30TEENR, J30TEEOB, J30TEERM, J30TEETA
0284714
 
0284714 ENGINE COVER ASSY.
BJ20SEEDA, BJ20SEEUM, BJ25EEDM, BJ25EEUB, BJ30EEDE, BJ30EEUD, HJ25TELEDA, J20EEOR, J25EEOA, J25TEEOR, J25TEEUM, J30EEOB, J30TEEDE, J30TEEOB, J30TEEUD
0284713
 
0284713 ENGINE COVER ASSY.
BJ20SEEDA, BJ20SEEUM, BJ25EEDM, BJ25EEUB, BJ30EEDE, BJ30EEUD, J20EEOR, J25EEOA, J30EEOB
0284396
 
0284396 ENGINE COVER ASSY.
J20EEOR, J25EEOA, J30EEOB
0284715
 
0284715 ENGINE COVER ASSY.
BJ20SEEDA, BJ20SEEUM, BJ25EEDM, BJ25EEUB, BJ30EEDE, BJ30EEUD, HJ25TELEDA, J20EEOR, J25EEOA, J25TEEOR, J25TEEUM, J30EEOB, J30TEEDE, J30TEEOB, J30TEEUD
0284133
 
0284133 ENGINE COVER ASSY.
J20EEOR, J25EEOA, J30EEOB
0437188
 
0437188 ENGINE COVER ASSY.
BJ20SEEDA, BJ25EEDM, BJ30EEDE, HJ25TELEDA, J20EEOR, J25EEOA, J25TEEOR, J30EEOB, J30TEEDE, J30TEEOB
Back to top