5005788 ENGINE COVER ASSY JOHNSON
J25RLSOA, J25RLSRR, J25RTSOS, J25WRLSOB, J25WRLSRM, J30RLSOD, J30RLSRE
ENGINE
Price: query
Rating:
BRP JOHNSON entire parts catalog list:
- ENGINE COVER » 5005788
J25RTSOS 2005
J25WRLSOB, J25WRSOB 2005
J25WRLSRM, J25WRSRM 2004
J30RLSOD, J30RSOD 2005
J30RLSRE, J30RSRE 2004
Information:
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     5P-3931     Anti-Seize Compound     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
The alignment of the bellows is important. Improper alignment may lead to premature failure of the bellows. Misalignment can be identified by visually inspecting the convolutions for uniformity of compression.Inspect the bellows for damage prior to installation. If there is any damage to the convolutions, discard the bellows. Minor damage to the ends of the bellows may be repaired. However, if there is any difficulty in installation after the repair, discard the bellows.
Illustration 1 g01004383
Illustration 2 g01502594
The ends of the bellows are very sharp. Injury could occur if the bellows are not handled properly. Handle the bellows by the convolutions.
Note: Refer to Special Instruction, REHS1728, "Application Guideline for the Bellows" for additional information on handling the bellows.
Install a new seal (17) and backup ring (16) in bellows (18) .
Use a suitable lifting device in order to install turbocharger (14) on the exhaust manifold and in the bellows on the precooler. The weight of the turbocharger is approximately 25 kg (55 lb).Note: If necessary, loosen clamp (13) and rotate the turbocharger housing in order to align the bellows for assembly.Note: Discard the locknuts after use. Use new locknuts for installation.
Apply Tooling (A) to the threads of the studs. Apply Tooling (A) to the mating surface of locknuts (12) . Install locknuts (12) . Tighten locknuts (12) in a numerical sequence to a torque of 54 5 N m (40 4 lb ft). Refer to Illustration 2.
Install clamp assembly (15) . Apply Tooling (A) to the threads of the clamp assembly and tighten to a torque of 12 2 N m (106 18 lb in).
If clamp assembly (13) was loosened, apply Tooling (A) to the threads of the clamp assembly and tighten to torque of 16 1 N m (142 9 lb in).
Illustration 3 g01003348
Connect hose assembly for the oil drain (11) (not shown).
Connect hose assembly for the oil supply (3) .
Connect hose (8) .
The ends of the bellows are very sharp. Injury could occur if the bellows are not handled properly. Handle the bellows by the convolutions.
Note: Refer to Special Instruction, REHS1728, "Application Guideline for the Bellows" for additional information on handling the bellows.
Install bellows (6) and duct (1) to the turbochargers.
Install clamp assembly (7) . Apply Tooling (A) to the threads of the clamp assembly and tighten to a torque of 12 4 N m (106 35 lb in).
Install clamp assembly (2) . Apply Tooling (A) to the threads of the clamp assembly and tighten to a torque of 12 4 N m (106 35 lb in).
The ends of the bellows are very sharp. Injury could occur if the bellows are not handled properly. Handle the bellows by the convolutions.
Note: Refer to Special Instruction, REHS1728, "Application Guideline for the Bellows" for additional information on handling the bellows.
Install bellows (10) and duct (5) on the turbochargers.
Install clamp assembly (9) . Apply Tooling (A) to the threads of the clamp assembly and tighten to a torque of 12 4 N m (106 35 lb in).
Install clamp assembly (4) . Apply Tooling (A) to the threads of the clamp assembly and tighten to a torque of 12 4 N m (106 35 lb in).
Parts engine JOHNSON:
0433392
0433392 ENGINE COVER, Lower
BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ30EECS, BJ30EEDE, BJ30EEEC, BJ30EEUD, BJ30E
5005000
5005000 ENGINE COVER ASSY
J25RLSNF, J25RLSOA, J25RLSRR, J25RLSTC, J25RTSOS, J25WRLSOB, J25WRLSRM, J30RLSNF, J30RLSOD, J30RLSRE, J30RLSTB