0319576 JOHNSON EXHAUST COVER,Outer


0319576 EXHAUST COVER,Outer JOHNSON 35E76G EXHAUST
0319576 EXHAUST COVER,Outer JOHNSON
Rating:
28

Buy EXHAUST COVER,Outer 0319576 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 23
 

Compatible models:

35E76G   JOHNSON

BRP JOHNSON entire parts catalog list:

35E76G, 35E76S, 35EL76G, 35EL76S, 35R76G, 35R76S, 35RL76G, 35RL76S 1976

Information:


Illustration 1 g01139787
(1) Thickness of the top plates ... 8.585 0.025 mm (0.3380 0.0010 inch) (2) Tighten the three studs to the following torque. ... 35 5 N m (26 4 lb ft) (3) Tighten the studs on top of the cylinder block to the following torque. ... 35 5 N m (26 4 lb ft) (4) There are two plugs on the front of the cylinder block. There are two plugs on the rear of the cylinder block. Apply 5P-3413 Pipe Sealant on the threads of the plugs before assembly. (5) The gasket that is between the cylinder block and the top plates is the following thickness. ... 0.208 0.025 mm (0.0082 0.0010 inch) (6) The dowels extend from the cylinder block. Distance ... 18.5 0.5 mm (0.73 0.02 inch) (7) Put 5P-3413 Pipe Sealant on the threads of the plugs before assembly. Tighten the plug that is in the front of the block and tighten the plug that is in the rear of the block to the following torque. ... 80 15 N m (60 11 lb ft) (8) Bore in the cylinder block for the camshaft bearings ... 76.835 0.018 mm (3.0250 0.0007 inch) (9) Bore in cylinder block for main bearings New bearings that are standard size ... 129.891 0.013 mm (5.1138 0.0005 inch) Bearings that are 0.64 mm (0.025 inch) larger than the standard size ... 130.526 0.013 mm (5.1388 0.0005 inch) (10) There are two dowels that are in the front of the cylinder block. There are two dowels that are in the rear of the cylinder block. The dowels project from the cylinder block. Distance ... 19.0 0.5 mm (0.75 0.02 inch) (11) The width of the slot for the main bearing caps is the following value. ... 215.900 0.013 mm (8.5000 0.0005 inch)Width of main bearing cap ... 215.900 0.025 mm (8.5000 0.0010 inch) (12) Use the procedure that follows to install the main bearing caps.
Illustration 2 g00285128
Marks For Tightening Main Bearings
Apply 4C-5593 Anti-Seize Compound on the threads of the bolts.
Tighten the bolts first on the bearing tab side of the cap.Torque for bolts ... 258 14 N m (190 10 lb ft)
Tighten the bolts that are opposite the bearing tab side of the cap.Torque for bolts ... 258 14 N m (190 10 lb ft)
Put a mark on each bolt and each cap.
Tighten the bolts that are opposite the bearing tab side of the cap from the mark to the following value.Angle from the mark. ... 120 5 degrees
Tighten the bolts on the bearing tab side of the cap from the mark to the following value.Angle from the mark. ... 120 5 degrees
Illustration 3 g00839257
(13) The distance from the centerline of the crankshaft bearing bore to the top of the cylinder block is the following value. ... 419.10 0.15 mm (16.500 0.006 inch) (14) The distance from the centerline of the crankshaft bearing bore to the bottom of the cylinder block is the following value. ... 165.10 0.10 mm (6.500 0.004 inch)


Parts exhaust JOHNSON:

0322090
 
0322090 EXHAUST COVER,Outer
25E77S, 25E78C, 35E76G, 35E77C, 35E78R
0319577
 
0319577 EXHAUST COVER,Inner
25E77S, 25E78C, 35E76G, 35E77C, 35E78R
0386902
 
0386902 EXHAUST HOUSING ASSY.-STD
25E77S, 25E78C, 25E79R, 35E76G, 35E77C, 35E78R, 35E79A
0386930
 
0386930 EXHAUST HOUSING ASSY.-LONG
25E77S, 25E78C, 25E79R, 35E76G, 35E77C, 35E78R, 35E79A
Back to top