0395892 JOHNSON EXTENSION KIT ASSY.

Illustration 1 g02006095
Right side view
Typical locations for the 12 cylinder engine and the 20 cylinder engine.
(1) Differential pressure sensor for the throttle valve
(2) Pressure sensor for turbocharger compressor outlet
(3) Temperature sensor for turbocharger compressor outlet
(4) Pressure sensor for the coolant outlet
(5) Emergency stop button
(6) Inlet manifold air pressure sensor
(7) Oil temperature sensor
(8) Pressure switch for the coolant pump (inlet)
(9) Timing calibration connector
(10) Pressure sensor for unfiltered oil
(11) Pressure sensor for filtered oil
Illustration 2 g02006115
Left side view
Typical locations for the 12 cylinder engine and the 20 cylinder engine.
(12) Coolant temperature sensor
(13) Inlet manifold air temperature sensor
(14) Engine speed/timing sensor
(15) Detonation sensor Throttle differential pressure sensor (1) - This sensor monitors the pressure drop across the throttle valve.Compressor outlet pressure sensor (2) - This sensor monitors the pressure of the air/fuel mixture from the turbocharger compressor outlet.Compressor outlet temperature sensor (3) - This sensor monitors the temperature of the air/fuel mixture from the turbocharger compressor outlet.Coolant pressure sensor (outlet) (4) - A pressure switch is located at the outlet for the engine jacket water. If the outlet pressure is too low, the ECM will activate a shutdown.Emergency stop button (5) - Pressing this button causes a shutdown.Inlet manifold air pressure sensor (6) - This sensor is connected to the inlet manifold. The sensor monitors the absolute manifold pressure. Absolute pressure is the atmospheric pressure plus the gauge pressure. The information is used by the ECM to calculate the air flow. To observe the output value of the sensor, use Cat ET to view the "Inlet Manifold Air Pressure (abs)".Oil temperature sensor (7) - An oil temperature sensor measures the engine oil temperature. A high oil temperature will activate an alarm or a shutdown. The trip points can be programmed with the Caterpillar Electronic Technician (Cat ET). To observe the output value of the sensor, use Cat ET to view the "Engine Oil Temperature" parameter.Pressure switch for the coolant pump (inlet) (8) - A pressure switch is located at the inlet for the engine jacket water. If the inlet pressure is too high, the switch will activate a shutdown. To observe the status of the switch, use the Caterpillar Electronic Technician (Cat ET) to view the "Engine Coolant Pump Pressure" parameter.Timing calibration connector (9) - The transducer for timing the engine is connected here.Oil pressure sensors (10) and (11) - The engine oil pressure is measured before the oil filters (10) and after the oil filters (11). An alarm or a shutdown can be activated by any of the following occurrences: low filtered oil pressure, low oil filter differential pressure and high oil filter differential pressure. The trip point for the activation of a warning or a shutdown for oil filter differential pressure can be programmed with Cat ET. To observe the value of the output of the sensor, use Cat ET to view the "Engine Oil Pressure" or the "Unfiltered Engine Oil Pressure" parameter.Coolant temperature sensor (12) - The temperature sensor is located in the water temperature regulator housing. To monitor the coolant temperature, the element must be in contact with the coolant. Otherwise, the sensor will not function properly. A high coolant temperature will activate an alarm or a shutdown. A low coolant temperature will only activate an alarm. The trip points for the activation can be programmed with Cat ET. The engine can be restarted after a shutdown due to high engine coolant temperature. However, another shutdown will occur after 1 minute if the temperature remains high. To observe the value of the output of the sensor, use Cat ET to view the "Engine Coolant Temperature" parameter.Inlet manifold air temperature sensor (13) - A sensor for monitoring the inlet air temperature is located in the inlet elbow for the number twelve cylinder. Excessive inlet air temperature can activate an alarm or a shutdown during high load or low load operation. The trip points for activation can be programmed with Cat ET. To observe the value of the output of the sensor, use Cat ET to view the "Inlet Air Temperature" parameter.Engine speed/timing sensor (14) - The engine speed/timing sensor is located at the rear end of the left camshaft. The ECM monitors the engine speed/timing sensor in order to determine the position of the crankshaft and the engine rpm. With the position of the crankshaft, the ECM is able to determine the ignition timing. To observe the engine speed in rpm, use Cat ET to view the "Engine Speed" parameter.Detonation sensors (15) - The detonation sensors monitor the engine for mechanical vibrations. Each sensor monitors two cylinders. The sensor produces a voltage signal that is proportional to the engine detonation. This information is processed by the ECM in order to determine detonation levels. To eliminate detonation, the ECM retards the timing of the cylinder. If detonation continues, the ECM will shut down the engine. To observe the value of the output of the sensors, use Cat ET to view the "Cylinder #X Detonation Level". The "X" is the number for the particular cylinder.