0436981 JOHNSON EXTENSION KIT ASSY.NG PARTS 20 INCH (308 MM) LONG PARTS


0436981 EXTENSION KIT ASSY.NG PARTS 20 INCH (308 MM) LONG PARTS JOHNSON BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, J10FEXEO, J15DLEOC EXTENSION
0436981 EXTENSION KIT ASSY.NG PARTS 20 INCH (308 MM) LONG PARTS JOHNSON
Rating:
73

Buy EXTENSION KIT ASSY.NG PARTS 20 INCH (308 MM) LONG PARTS 0436981 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 43698
 

BRP JOHNSON entire parts catalog list:

BJ10FDLECM, J10FEXECM, J10FRECM, J10FRELECM, J10FRLECM 1998
BJ10FDLEDR, BJ10FPXEDC, BJ10FRELDR, J10FEXEDR, J10FREDR, J10FRELEDR, J10FRLEDR 1996
BJ10FDLEUA, BJ10FPXEUR, BJ10FRELUA, J10FEXEUA, J10FRELEUA, J10FREUA, J10FRLEUA 1997
BJ15FAEDR, BJ15FDLEDR, BJ15FKEDR, BJ15FREDR, BJ15FRELEDR, BJ15FWEDC, BJ15FWLEDC, J15FKEDR, J15FREDR, J15FRELEDR, J15FRLEDR 1996
BJ15FAEUA, BJ15FDLEUA, BJ15FKEUA, BJ15FRELUA, BJ15FREUA, BJ15FWEUR, BJ15FWLEUR, J15FKEUA, J15FRELEUA, J15FREUA, J15FRLEUA 1997
BJ15FDLECM, BJ15FWECA, BJ15FWLECA, J15FRECM, J15FRELECM, J15FRLECM 1998
J10FEXEO, J10FRELEOC, J10FREOC, J10FRLEO 1995
J15DLEOC, J15FREOC, J15FRLEOC, J15KEOC 1995

Information:

1. Loosen bolts (1) and (2) on the alternator brackets.2. Move the alternator towards the engine, and remove V-belts (3) from the alternator drive pulley.
Make sure that support assembly (5) and the fan drive do not fall in Step 3. They could cause damage to the radiator core.
3. Attach a lifting sling and a hoist to the fan drive. Remove two bolts (4) and washers from support assembly (5). 4. Move the fan drive and support assembly (5) in order to allow access to six bolts (6) and washers. Remove six bolts and washers (6) that hold fan (7) to the fan drive.5. Remove fan (7) from the fan drive. The weight of fan (7) is 25 Kg (55 lb). 6. Remove four bolts (8) and washers from fan drive (9) and support assembly (5). Remove fan drive (9) from support assembly (5). The weight of fan drive (9) is 30 Kg (65 lb). If fan drive and support assembly are removed together the weight is 56 Kg (123 lb).Install Fan & Fan Drive
Check the condition of the fan assembly for damage or broken fan blades. Check the condition of the hub area of the fan assembly. If the part is damaged, use a new part for replacement. 1. Attach a lifting sling and a hoist to fan drive (9). Position fan drive (9) to support assembly (5). The weight of fan drive (9) is 30 Kg (65 lb).2. Install four bolts (8) and washers to fan drive (9) and support assembly (5). 3. Position fan (7) to fan drive (9) with the side marked "front" away from the radiator core. The weight of fan (7) is 25 Kg (55 lb).4. Install six bolts (6) and washers in order to secure fan (7) to fan drive (9). 5. Position support assembly (5) to its original location. Install two bolts (4) and washers in order to secure support assembly (5) to its mounting. Remove the lifting strap. 6. During the installation of the V-belts, check the condition of all the V-belts. If any of the V-belts are damaged, use new parts for replacement.7. Install V-belts (3) on the alternator drive pulley.8. Tighten bolts (1) and (2) on the alternator brackets.9. Adjust the V-belt tension. Refer to the "Operation & Maintenance Manual" for the proper procedure of adjusting (new or used) V-belt tension.10. Tighten the fan V-belts until they deflect 12 mm (1.2 in) for new V-belts, or 5/8 16 mm ( in) for old V-belts under the application of a 13 Kg (25 lb) force half way between the pulleys.11. A Burroughs Gauge No. BT-33-72-4-15 can also be used to make the fan V-belt adjustment. Make an adjustment to the V-belt farthest from the engine. The gauge reading for a new V-belt must be 120 5 and for a V-belt with a minimum of 30 minutes of operation time 90 10.End By:a. install hoodDisassemble & Assemble Fan Drive
Start By:a. remove fan drive 1. Remove bolts (7), and remove bracket assembly (9) from bracket (8).2. Remove bolts (5). Remove adapter (1) from hub (3). Remove seal (2) from adapter (1).3. Remove bolts (15) and washer (14). Remove hub (3) and pulley (4) from the shaft on bracket assembly (9). Remove pulley (4) from hub (3).4. Remove bearing (13) and spacer (6) from the hub. Remove spacer (12), bearing (11), and seal (10) from the shaft on bracket assembly (9). The following steps are for the installation of the fan drive.5. Clean and inspect all parts. Make a replacement of all parts that are worn or damaged.6. Lubricate sealing lip of seal (10) lightly with the lubricant being sealed. Install seal (10) in hub (3) with Tooling (A). Install the lip of the seal toward the outside of the hub.7. Install bearing (11) in the hub. Install spacer (12) and spacer (6) in the hub. Fill the hub with 5P-0960 Multi-Purpose Grease. Install bearing (13) in the hub.8. Install pulley (4) on hub (3), and install the hub on the shaft on bracket assembly (9). Install washer (14) and bolts (15).9. Install seal (2) in adapter (1). Install adapter (1) on hub (3) with bolts (5).10. Install bracket assembly (9) on bracket (8) with bolts (7).End By:a. install fan drive


Parts extension JOHNSON:

0319340
 
0319340 EXTENSION,Impeller housing to exhaust housin g 5" LONGER PARTS
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15FAEDR, BJ15
0331152
EXTENSION, Gearcase
0331152 EXTENSION, Gearcase
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, BJ15RELEUC, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA, HJ15KCF, HJ15KCLN, HJ
0395894
 
0395894 EXTENSION, Gearcase
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ15EEDS, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, BJ15RELEUC, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, HJ10FELECA, J10ECCD, J10ECDB, J10ECES, J10ECOM, J10ECUE, J10EECC, J10EEIR, J10EEN
Back to top