0584374 JOHNSON FLYWHEEL ASSY.


0584374 FLYWHEEL ASSY. JOHNSON BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, HJ20CREDA, HJ25FPV, HJ25RLEDA, HJ30REDE, J20CREOR, J20CRERC, J20CRETS, J25JREDC, J25JREEM, J25JREOS, J25JRSIE, J25JRSSB, J25REOR, J25RERC, J FLYWHEEL
0584374 FLYWHEEL ASSY. JOHNSON
Rating:
68

Buy FLYWHEEL ASSY. 0584374 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 2
 

BRP JOHNSON entire parts catalog list:

BJ20SRECB, BJ20SRLECB 1998
BJ20SREDA, BJ20SRLEDA 1996
BJ20SREUM, BJ20SRLEUM, J20CREUM, J20CRLEUM 1997
BJ25BAECM, BJ25BALECM, J25JRECA, J25RECB, J25RLECB, SJ25RDECA 1998
BJ25BAEDR, BJ25BALEDR, BJ25BREDC, BJ25BRLEDC, HJ25RAEDA, SJ25RDEDC 1996
BJ25BAEUA, BJ25BALEUA, HJ25RAEUM, J25JREUR, J25REUM, J25RLEUM, SJ25RDEUR 1997
BJ30BAECS, BJ30BALECS 1998
BJ30BAEDE, BJ30BALEDE 1996
BJ30BAEEC, BJ30BAEEN, J30REEC, J30REEN, J30RLEEC, J30RLEEN 1999
BJ30BAEUD, BJ30BALEUD, J30REUD, J30RLEUD 1997
HJ20CREDA, HJ20CRLEDA, J20CREDA, J20CRLEDA 1996
HJ25FPV, HJ25RLSV, J25RWEUR, J25RWLEUR, SJ25RPLV, SJ25RPV 1997
HJ25RLEDA, J25REDA, J25RLEDA, SJ25REDA, SJ25RLEDA 1996
HJ30REDE, HJ30RLEDE, J30REDE, J30RLEDE, SJ30REDE, SJ30RLEDE 1996
J20CREOR, J20CRLEOR 1995
J20CRERC, J20CRLERC 1994
J20CRETS, J20CRLETS, TJ20CRETS, TJ20CRLETS 1993
J25JREDC 1996
J25JREEM, J25JREEN, J25REEB, J25REEN, J25RLEEB, J25RLEEN, SJ25RDEEM, SJ25RDEEMN, SJ25RTEEM 1999
J25JREOS 1995
J25JRSIE, J25RLSID, J25RSID, J25RVLSID, J25RVSID, SJ25RTSIE 2001
J25JRSSB, J25RLSSE, J25RSSE, SJ25RTSSB 2000
J25REOR, J25RLEOR 1995
J25RERC, J25RLERC 1994
J25RETS, J25RLETS 1993
J25RLSNF, J25RSNF 2002
J25RLSOA, J25RSOA 2005
J25RLSRR, J25RSRR 2004
J25RLSTC, J25RSTC 2003
J25RTSOS 2005
J25WREEN, J25WREES, J25WRLEEN, J25WRLEES 1999
J25WRLSIR, J25WRSIR 2001
J25WRLSOB, J25WRSOB 2005
J25WRLSRM, J25WRSRM 2004
J25WRLSSC, J25WRSSC 2000
J30MLSRC 2004
J30MLSTS 2003
J30REOB, J30RLEOB 1995
J30RERM, J30RLERM 1994
J30RETA, J30RLETA 1993
J30RLSIA, J30RSIA, J30RVLSIA, J30RVSIA 2001
J30RLSNF, J30RSNF 2002
J30RLSOD, J30RSOD 2005
J30RLSRE, J30RSRE 2004
J30RLSSR, J30RSSR 2000
J30RLSTB, J30RSTB 2003
J35RERM, J35RLERM 1994
J35RETA, J35RLETA 1993
SJ25RPLP, SJ25RPP 1998
SJ35REDE, SJ35RLEDE 1996

Information:

1. Fasten a hoist to implement pump (1) and remove the pump. The weight of implement pump (1) is 29 kg (75 lb.). 2. Remove plates (2).3. Remove pump drives (3) with tool (A) and a hoist. The weight of each pump drive is 29 kg (65 lb.). 4. Remove plate (4). 5. Remove starting motor (5) and disconnect oil supply line (6) at the flywheel housing. 6. Remove engine rear supports (7). 7. Remove turbocharger oil supply line (8) and bracket (9). 8. Remove top section of turbocharger heat shield (10). 9. Remove turbocharger drain line (11) and elebow (12). 10. Remove plate (13). 11. Remove bolts (14) and the remainder of the bolts which hold bracket (15) to the engine and remove bracket (15). 12. Use tooling (A) and fasten a hoist to flywheel housing (16). Remove the bolts that hold flywheel housing (16) in position and pull flywheel housing off the dowels and remove it. The weight of the flywheel housing is 191 kg (425 lb.).13. Put the flywheel housing in the position shown. 14. Remove bolts (17) from shafts (19).
Bearings (20) can fall out of gears (18) when the gears are removed from the flywheel housing.
15. Remove gears (18) from the flywheel housing. 16. Remove shafts (19), bearing cones (22), spacers (21) and bearing cones (20) from gears (18). 17. If necessary, remove bearing cups (23) and (25), spacers (24) and the snap rings from gears (18). The bearing cups will have damage after removal. Use new parts for replacement.Install Flywheel Housing
1. Install the snap rings in the groove in idler gear (2).2. Install the spacers for bearing cups (1) in gears (2) from the side of gears (2) that have the part number. Make sure the notches in the spacers are toward the snap rings. The snap rings are not in the center of the gear bores. The spacers must be installed in the gear bores that have the longer measurement from the snap ring to the surface of the gear.3. Lower the temperature of bearing cups (1) and install them in gears (2) until they make contact with the spacers. 4. Put the flywheel housing in the position shown and install bearing cones (3). 5. Put idler gears (2) in position on the bearing cones. Make sure the side of gears (2) with the part number is toward the flywheel housing. 6. Put spacer (4) on the inner race of the bearing cone. 7. Install bearing cones (5) in the gears. 8. Install shafts (6) and the bolts to hold them.
Put the No. 1 piston at top dead center to make an alignment of the timing marks on the crankshaft rear gear (9) with the balancer gear (8). Failure to follow this procedure can cause damage to the engine.
9. Clean the front face of the flywheel housing and the rear face of the cylinder block. Make an application of 20 ml (.7 oz.) of 6V6640 Bulk Gasket as a not broken (continuous) line inside the center line of the holes in the flywheel housing. Remove excess gasket material. 10. Use tooling (A) and fasten a hoist to flywheel housing (7). Make an alignment of the timing marks on the crankshaft rear gear (9) and the balancer gear (8). 11. Tighten the flywheel housing bolts as follows: a. Tighten bolts 1 through 8 in number sequence shown to a torque of 135 14 N m (100 10 lb.ft.).b. Tighten bolts 9 through 21 in number sequence shown to a torque of 54 7 N m (40 5 lb.ft.).c. Tighten bolts 1 through 8 again in number sequence shown to a torque of 135 14 N m (100 10 lb.ft.).d. Tighten bolts 9 through 21 again in number sequence shown to a torque of 54 7 (40 5 lb.ft.). 10. Put bracket (10) in position and install the bolts through the lower section of the turbocharger heat shield. 11. Install plate (11). 12. Install drain line (12) and elbow (13). 13. Install the top section of turbocharger heat shield (14). 14. Install bracket (15) and turbocharger oil return line (16). 15. Install engine rear supports (17). 16. Connect oil supply line (18) to the flywheel housing and install starting motor (19). 17. Install cover (21) with a new O-ring seal (20). 18. Install pump drives (23) and plates (22). 19. Install implement pump (24).End By:a. install oil panb. remove crankshaft rear seal and wear sleeve


Back to top