0115726 JOHNSON FRICTION PLATE


0115726 FRICTION PLATE JOHNSON BJ2REDE, BJ2REUD, BJ3ROEDE, BJ3ROEUD, HJ2DRETC, HJ3RETC, J2RECS, J2REEC, J2ROEOB, J2RTSIA, J2RTSSR, J2WREES, J2WRSIR, J2WRSSC, J3REEC, J3ROECS, J3ROEOB, J3RTLSIA, J3RTLSSR, J3WREES, J3WRSIR, J3WRSSC FRICTION
0115726 FRICTION PLATE JOHNSON
Rating:
18

Buy FRICTION PLATE 0115726 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 8
 

BRP JOHNSON entire parts catalog list:

BJ2REDE, HJ2REDE, HJ2RSA, J2ROEDE, SJ2REDE 1996
BJ2REUD, HJ2REUD, HJ2RSK, J2ROEUD 1997
BJ3ROEDE, HJ3ROEDE, HJ3RSA, J3ROEDE, SJ3ROEDE 1996
BJ3ROEUD, HJ3ROEUD, HJ3RSK, J3ROEUD, SJ3ROEUD 1997
HJ2DRERM, HJ2DRETC 1993,1994
HJ3RERM, HJ3RETC 1993,1994
J2RECS, J2RSS 1998
J2REEC 1999
J2ROEOB 1995
J2RTSIA, J2RTVSIA 2001
J2RTSSR 2000
J2WREES 1999
J2WRSIR 2001
J2WRSSC 2000
J3REEC, J3RLEEC 1999
J3ROECS, J3ROLECS, J3RSS 1998
J3ROEOB 1995
J3RTLSIA, J3RTSIA, J3RTVSIA 2001
J3RTLSSR, J3RTSSR 2000
J3WREES 1999
J3WRSIR 2001
J3WRSSC 2000

Information:

4. Remove water pump, and remove elbow (6) from pump. The following steps are for installation of the water pump.5. Install the gasket and elbow on the water pump.6. Be sure the O-ring seal is in position on the water pump. Put clean oil on the O-ring seal. Put water pump (4) in position on the timing gear cover and install the two bolts that hold it in place. Do not tighten the bolts at this time.7. Put the gasket in place between the elbow and the cylinder head. Install the two bolts that hold the elbow to the cylinder head.8. Tighten all four bolts that hold the elbow and water pump in place.9. Position hoses (2) and (3) and tighten the clamps.10. Connect wires (1) to the temperature switch.11. Fill the cooling system with coolant to the correct level. See Maintenance Guide.Disassemble Water Pump
Start By: a. remove water pump 1. Remove cover (1) from water pump (2). 2. Loosen bolt (3) on impeller (4) 6.35 mm (.25 in.). Hit the bolt with a soft hammer to remove the impeller from the shaft. 3. Remove spring and seal assembly (5) from the shaft (6). 4. Turn the housing over and remove bolt and washer (7). Remove bearing (8) and gear (9) as a unit. 5. Use tool (A), tooling (C) and a press to remove bearing (8) from gear (9). 6. Remove snap ring (10) with tool (B). 7. Remove bearing (11) and shaft (6) as a unit. 8. Use tool (A) and a press to remove bearing (11) from the shaft. 9. Remove the ceramic ring and seal (12) from the housing. 10. Remove the lip seal (13) from the housing with tool (C). Assemble Water Pump
1. Install the lip-type seal in the water pump housing with tool (A). The lip of the seal must be toward the bearings. Put clean engine oil on the lip of the seal. 2. Install shaft (1) in bearing (2) with a press. 3. Install shaft (1) and bearing (2) in the housing as shown. 4. Install snap ring (3) with tool (B).
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Put ceramic ring (4) in position in the rubber seal. Use hand pressure and the tool (which is with the replacement ring) to install the ceramic ring. 6. Remove the spring from seal assembly (5). Use hand pressure and the tool (which is with the replacement ring) to install the seal assembly. Push seal assembly (5) on the shaft until it makes light contact with ceramic ring (4). 7. Install spring (6) as shown. Put impeller (7) in position on the shaft, and install the washer and bolt that hold it. Tighten the bolt to a torque of 39 1 N m (28 1 lb. ft.). 8. Put the gasket and cover (8) in position on the water pump housing, and install the washers and bolts (9) that hold them. 9. Install bearing (10) on gear (11) with a press. 10. Align pins (12) on gear (11) and the holes in shaft (1). Put the gear and bearing in position on the shaft, and install the washer and bolt that hold them together.End By: a. install water pump


Parts friction JOHNSON:

0115527
 
0115527 FRICTION SPRING
BJ2REDE, BJ2REUD, BJ3ROEDE, BJ3ROEUD, HJ2DRETC, HJ3REIC, HJ3RENR, HJ3RETC, J2RECS, J2REEC, J2ROEOB, J2RTSIA, J2RTSSR, J2WREES, J2WRSIR, J2WRSSC, J3REEC, J3ROECS, J3ROEOB, J3RSDE, J3RSNF, J3RSOD, J3RSRE, J3RSTB, J3RTLSIA, J3RTLSSR, J3WREES, J3WRSIR, J
0115530
 
0115530 FRICTION PLATE
BJ2REDE, BJ3ROEDE, HJ2DRETC, HJ3REIC, HJ3RENR, HJ3RETC, J2ROEOB, J3ROEOB, J3RSNF, J3RSOD, J3RSRE, J3RSTB
Back to top