0329378 JOHNSON GASKET,Inner cover 235 S model only


0329378 GASKET,Inner cover 235 S model only JOHNSON J150CXCCA, J150TLCDC, J150TLCOS, J150TLCRD, J150TLCTB, J150TLCUR, J175STLACM, J175TLCDR, J175TLCOC, J175TLCTD, J175TLCUA, J185TLCOC, J185TLCRS, J200TLCTD, J235TLCOR, J235TLCRC, J235TLCTD GASKET
0329378 GASKET,Inner cover 235 S model only JOHNSON
Rating:
13

Buy GASKET,Inner cover 235 S model only 0329378 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 39
 

BRP JOHNSON entire parts catalog list:

J150CXCCA, J150TLCCA, J150TXCCA 1988
J150TLCDC, J150TXCDC 1986
J150TLCOS, J150TXCOS 1985
J150TLCRD, J150TXCRD 1984
J150TLCTB, J150TLCTE, J150TXCTB, J150TXCTE 1983
J150TLCUR, J150TXCUR 1987
J175STLACM, J175STLCCM, J175TLCCM, J175TXCCM 1988
J175TLCDR, J175TXCDR 1986
J175TLCOC, J175TXCOC 1985
J175TLCTD, J175TLCTE, J175TXCTD, J175TXCTE 1983
J175TLCUA, J175TXCUA 1987
J185TLCOC, J185TXCOC 1985
J185TLCRS, J185TXCR 1984
J200TLCTD, J200TLCTS, J200TXCTD, J200TXCTS 1983
J235TLCOR, J235TXCOR 1985
J235TLCRC, J235TXCRC 1984
J235TLCTD, J235TLCTS, J235TXCTD, J235TXCTS 1983

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A - Guide Studs
M16 by 140mm 2
B 8T-3052 Degree Wheel 1
C - Delphi Lockheed Rubber Grease 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the wiring harness assembly is correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting.
Thoroughly clean the gasket surfaces of the cylinder head and the cylinder block. Do not damage the gasket surfaces of the cylinder head or the cylinder block. Ensure that no debris enters the cylinder bores, the coolant passages, or the lubricant passages.
Inspect the gasket surface of the cylinder head for distortion. Refer to Specifications, "Cylinder Head" for more information. If the gasket surface of the cylinder head is distorted beyond maximum permitted limits, replace the cylinder head.
Illustration 1 g06358801
Inspect dowels (7) for damage. If necessary, replace the dowels (7) in the cylinder block.
Install Tooling (A) to the cylinder block (9).
Align cylinder head gasket (8) with dowels (7). Install cylinder head gasket (8) onto the cylinder block.
Use a suitable lifting device to lift cylinder head. The weight of the cylinder head is approximately 50 kg (110 lb).Note: A spreader bar must be used to distribute the weight of the cylinder head during the lifting operation.
Use Tooling (A) to align the cylinder head with the cylinder block. Install the cylinder head to the cylinder block.Note: Ensure that the cylinder head is correctly positioned on dowels (7).
Remove Tooling (A).
Illustration 2 g06386875
Clean bolts (5). Use a straight edge to check the threads of the bolts. Refer to Illustration 2. Replace any bolts that show visual reduction in the diameter of the thread over Length (Y).
Lubricate the threads and the shoulders of bolts (5) with clean engine oil.
Illustration 3 g06358393
Illustration 4 g06358708
Install bolts (5) to cylinder head (6).
Tighten the bolts to a torque of 50 N m (37 lb ft) in the numerical sequence. Refer to Illustration 4.
Tighten the bolts to a torque of 100 N m (74 lb ft) in the numerical sequence. Refer to Illustration 4.
Use Tooling (B) to turn the bolts through an additional 250 degrees in the numerical sequence. Refer to Illustration 4.
Illustration 5 g06358700
Remove bolts (3) from lighting eye (2). Remove lifting eye (2) from cylinder head (6).
Illustration 6 g06359884
Install lifting eye (2) into Position (Y) on the CEM bracket (4). Install bolts (3) tighten the bolts to a torque of 44 N m (32 lb ft).
Reconnect the inlet manifold temp and pressure sensor. Refer to Disassembly and Assembly, Inlet Manifold Temperature and Pressure Sensor - Remove and Install for the correct procedure.
Reconnect the EGR temperature sensor to Disassembly and Assembly, Temperature Sensor (Cooled Exhaust Gas) - Remove and Install for the correct procedure.
Reconnect the coolant temperature sensor. Refer to Disassembly and Assembly, Coolant Temperature Sensor - Remove and Install for the correct procedure.
Position the harness assembly onto the cylinder head. Use new cable straps to secure the harness assembly to the cylinder head. Ensure that cable straps meet the OEM specification. Ensure that the harness assembly is not strained.Note: Ensure that the harness assembly is positioned correctly and clear of other engine components.
Illustration 7 g06357254
If necessary, install water temperature regulator housing (1) to the cylinder head. Refer to Disassembly and Assembly, "Water Temperature Regulator Housing - Remove and Install" for the correct procedure.
Connect the upper radiator hose to water temperature regulator housing (1) on the cylinder head.End By:
Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install" for the correct procedure.
Install the glow plugs. Refer to Disassembly and Assembly, "Glow Plugs - Remove and Install" for the correct procedure.
Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install" for the correct procedure.
Install the fuel manifold. Refer to Disassembly and Assembly, "Fuel Manifold (Rail) - Remove and Install" for the correct procedure.
Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Insta


Parts gasket JOHNSON:

0301996
 
0301996 GASKET
100ESL71A, 100ESL72R, 100ML79S, 10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78
0312679
 
0312679 GASKET,Filter screen
100ESL71A, 100ESL72R, 100ML79S, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL7
0320745
GASKET,Cylinder head
0320745 GASKET,Cylinder head
150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL76S, 200TL77C, 200TL78R, 200TL79A, 235TL70A, 235TL78R, J150CXCCA, J150CXCEM, J150GTLCUR, J150STLACA, J150STLCDC, J150STLCEM, J150STLCOH, J150STLCRD, J150STLCTE, J150TLCDC, J150TLCIA, J150TLCNM, J
0321028
GASKET,Cover
0321028 GASKET,Cover
150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL76S, 200TL77C, 200TL78R, 200TL79A, 235TL70A, 235TL78R, J150CXCCA, J150CXCEM, J150CXEIE, J150CXESB, J150GTLCUR, J150STLACA, J150STLCDC, J150STLCEM, J150STLCOH, J150STLCRD, J150STLCTE, J150STLEIE,
0321184
GASKET,Thermostat cover
0321184 GASKET,Thermostat cover
150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL76S, 200TL77C, 200TL78R, 200TL79A, 235TL70A, 235TL78R, J150CXCCA, J150CXCEM, J150CXEIE, J150CXESB, J150GTLCUR, J150STLACA, J150STLCDC, J150STLCEM, J150STLCOH, J150STLCRD, J150STLCTE, J150STLEIE,
0323222
 
0323222 GASKET,Innerexh.hsg.toplate
150TL78S, 150TL79C, 175TL78C, 175TL79R, 200TL78R, 200TL79A, 235TL70A, 235TL78R, J120TLCDC, J120TLCOS, J120TLCUR, J140TLCDC, J140TLCOS, J140TLCUA, J150CXCCA, J150CXCEM, J150CXEIE, J150CXESB, J150GTLCUR, J150STLACA, J150STLCDC, J150STLCEM, J150STLCOH,
0323784
 
0323784 GASKET, Float bowl
100ML79S, 115ML79R, 140ML79R, 150TL79C, 175TL79R, 200TL79A, 235TL70A, 85ML79R, J100MLCSC, J100WMLCDR, J100WMLCOC, J100WMLCRS, J110MLCDC, J115MLCIH, J115MLCNB, J115MLCOS, J115MLCRD, J115MLCSA, J115MLCTE, J140MLCIH, J140MLCNB, J140MLCSA, J140MLCTE, J14
0123906
GASKET
0123906 GASKET
CJ275TLCDC, CJ275TLCOS, CJ300TLCDC, CJ300TLCOS, D100WTLM, J100STLCCA, J100STLCEM, J100STLEIE, J100STLEND, J100STLESB, J100WMLCDR, J100WMLCOC, J100WTLCUA, J100WTLEIB, J100WTLENE, J100WTLESM, J100WTLZ, J110MLCCA, J110MLCDC, J110MLCEM, J110MLCUR, J115JL
Back to top