5034334 JOHNSON GASKET, LOWER COVER PLATE


5034334 GASKET, LOWER COVER PLATE JOHNSON J4R4SDA, J4R4SOR, J4R4SRC, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR GASKET
5034334 GASKET, LOWER COVER PLATE JOHNSON
Rating:
89

Buy GASKET, LOWER COVER PLATE 5034334 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 7
 

BRP JOHNSON entire parts catalog list:

J4R4SDA, J4RL4SDA 2006
J4R4SOR, J4RL4SOR 2005
J4R4SRC, J4RL4SRC 2004
J4R4SUM, J4RL4SUM 2007
J5R4SDA, J5RL4SDA 2006
J5R4SOR, J5RL4SOR 2005
J5R4SRC, J5RL4SRC 2004
J5R4SUM, J5RL4SUM 2007
J6R4SDC, J6RL4SDC 2006
J6R4SOS, J6RL4SOS 2005
J6R4SUR, J6RL4SUR 2007

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 136-4632 Timing Pin 1
C 1P-2320 Combination Puller 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Put identification marks on all hoses, on all hose assemblies and on all tube assemblies for installation purposes. Plug all hose assemblies and tube assemblies. Plugging all hose assemblies and tube assemblies helps to prevent fluid loss and also helps to keep contaminants from entering the system.
Do not disconnect the air lines until the air pressure in the system is at zero. If hose is disconnected under pressure it can cause personal injury.
Release the pressure from the air system. Refer to the Original Equipment Manufactures (OEM) for the correct procedure.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.
If the engine is equipped with a hydraulic pump on the rear of the air compressor, remove the hydraulic pump. Refer to the OEM for the correct procedure.
Use Tooling (A) in order to rotate the crankshaft so that number one piston is at the top center position on the compression stroke. Refer to Systems Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure. Note: The air compressor must be timed with the engine in order to minimize engine vibration.
Illustration 1 g01966313
Typical example
Remove plug (2) from the cylinder block. Remove O-ring seal (1) from the plug.
Install Tooling (B) into Hole (X) in the cylinder block. Use Tooling (B) in order to lock the crankshaft in the correct position. Note: Do not use excessive force to install Tooling (B). Do not use Tooling (B) to hold the crankshaft during repairs.
Illustration 2 g01964836
Typical example
Illustration 3 g01965121
Typical example
Slide hose clamps along coolant hose (3) and coolant hose (4). Disconnect coolant hose (3) and coolant hose (4) from air compressor (6).
Disconnect the air lines from port (5) (not shown) and air lines from port (7). Refer to the OEM for the correct procedure.
Remove banjo bolt (9) and sealing washers from air compressor (6).
Remove bolt (10) and bolt (12) from support bracket (11) and remove the support bracket.
Support air compressor (6) and remove nuts (15). Remove the air compressor from front housing (8).
If necessary, remove studs (14) from front housing (8).
If necessary, remove bolts (17) and remove plate (16). Remove O-ring seal (13) from plate (16).
Illustration 4 g01964860
Typical example
Remove O-ring seal (21) from air compressor (6).
If necessary, follow Step 15.a through Step 15.b in order to remove gear (18) from the crankshaft of the air compressor.
Use a suitable tool in order to prevent the shaft of the compressor from rotating. Remove nut (20) and remove spring washer (19).
Use Tooling (C) in order to remove gear (18) from the crankshaft of the air compressor.
Illustration 5 g02091596


Parts gasket JOHNSON:

5031036
 
5031036 GASKET, Float chamber
J4R4SRC, J4R4STS, J5R4SRC, J5R4STS, J5RECS, J5REEC, J5RLSIM, J5RLSSA
5031037
 
5031037 GASKET, Bolt
J4R4SRC, J4R4STS, J5R4SRC, J5R4STS, J5RECS, J5REEC, J5RLSIM, J5RLSSA
5030071
GASKET, Drain & fill plug
5030071 GASKET, Drain & fill plug
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, BJ60PL4SDM, BJ60PL4SOA,
5033364
GASKET, CARBURETOR
5033364 GASKET, CARBURETOR
J4R4SRC, J4R4STS, J5R4SRC, J5R4STS
5034169
 
5034169 GASKET, CRANKCASE
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR
5033342
 
5033342 GASKET, CYLINDER HEAD
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR
5033345
 
5033345 GASKET, CYLINDER HEAD
J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR
5034446
 
5034446 GASKET, DRIVE SHAFT HSG
J4R4SDA, J4R4SOR, J4R4SRC, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4SUM, J6R4SDC, J6R4SOS, J6R4SUR
Back to top