5032783 JOHNSON GUIDE, OIL LEVEL GAUGE


5032783 GUIDE, OIL LEVEL GAUGE JOHNSON BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC GUIDE
5032783 GUIDE, OIL LEVEL GAUGE JOHNSON
Rating:
64

Buy GUIDE, OIL LEVEL GAUGE 5032783 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$44.24
 

05-12-2020
4.40924524[1.80] Pounds
-: -
Connected Essentials 5032783 Tailored Heavy Duty Custom Fit Car Mats, for Civic (2012-), Grey with Black Trim, Premium
Complete set of 4 tailored custom fit car mats - designed and manufactured specifically for Honda Civic (2012-) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Number on catalog scheme: 8
 

BRP JOHNSON entire parts catalog list:

BJ40PL4SDR, J40PL4SDE 2006
BJ40PL4SOC, J40PL4SOB 2005
BJ40PL4SRS, J40PL4SRM 2004
BJ50PL4SDR, J50PL4SDE 2006
BJ50PL4SOC, J50PL4SOB 2005
BJ50PL4SRS, J50PL4SRM 2004
J40PL4SNF 2002
J40PL4STC 2003
J50PL4SNF 2002
J50PL4STC 2003

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 370-8376 Capping Kit 1 Start By:
Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove" for the correct procedure.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Illustration 1 g02484242
Illustration 2 g02484286
Thoroughly clean the area around fuel manifold (1).
Disconnect harness assembly (4) from fuel pressure sensor (5).
Remove banjo bolt (3) from plastic tube assembly (2). Use Tooling (A) to plug the plastic tube assembly Remove sealing washers (7) (not shown). Use Tooling (A) to plug fuel manifold (1).
Remove bolts (6).
Remove fuel manifold (1) from the cylinder block.
If necessary, remove fuel pressure relief valve (8) from fuel manifold (1). Ref to Disassembly and Assembly, "Relief Valve (Fuel) - Remove and Install" for the correct procedure. Installation Procedure
Ensure that all adjustments and repairs that are carried out to the fuel system are performed by authorized personnel that have the correct training.Before beginning ANY work on the fuel system, refer to Operation and Maintenance Manual, "General Hazard Information and High Pressure Fuel Lines" for safety information. Refer to System Operation, Testing and Adjusting, "Cleanliness of Fuel System Components" for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
Ensure that all ports on the fuel manifold are capped. Ensure that the fuel manifold is externally clean and free from damage. Note: Do not install a fuel manifold that has not been capped. All caps must be left in place until the fuel injection lines are installed.
Illustration 3 g02484242
Illustration 4 g02484286
If necessary, install fuel pressure relief valve (8) to fuel manifold (1). Ref to Disassembly and Assembly, "Relief Valve (Fuel) - Remove and Install" for the correct procedure.
Position fuel manifold (1) onto the cylinder block. Install bolts (6) to fuel manifold (1) finger tight.
Install a new set of seals to the electronic unit injectors and a new set of fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Install" for the correct procedure.
Tighten bolts (6) to a torque of 22 N m (195 lb in).
Install a new sealing washer (7) (not shown) to banjo bolt (3).
Remove plug from plastic tube assembly (2). Install assembly of banjo bolt (3) to plastic tube assembly (2). Install remaining new sealing washer (7) (not shown) to banjo bolt (3).
Install banjo bolt (3) and plastic tube assembly (2) to pressure relief valve (8) finger tight.
Tighten banjo bolts (3) to a torque of 15 N m (133 lb in).
Connect harness assembly (4) to fuel pressure sensor (5).
Remove the air from the fuel system. Refer to Operation and Maintenance Manual, "Fuel System - Prime" for the correct procedure.


Parts guide JOHNSON:

5031598
 
5031598 *GUIDE, VALVE
BJ40PL4SRS, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031452
 
5031452 GUIDE, SHIFT ROD
BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031453
 
5031453 GUIDE, SHIFT ROD LOWER
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5031332
 
5031332 GUIDE, TIMING CHAIN
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC
5034434
 
5034434 *GUIDE, VALVE
BJ40PL4SDR, BJ40PL4SOC, BJ50PL4SDR, BJ50PL4SOC
5036053
 
5036053 GUIDE, SHIFT ROD
BJ40PL4SDR, BJ50PL4SDR
Back to top