0127055 JOHNSON HANDLE, Remote control


0127055 HANDLE, Remote control JOHNSON HJ55WMLM, HJ55WMLZ, J125WTPLE, J150WPLEES, J150WPLSIF, J150WPLSSC, J150WTLEOR, J150WTLERC, J200WPXEEN, J200WPXSIF, J200WPXSSC, J65WELSIR, J65WELSSC, SJ125WTPLJ, SJ125WTPLN, SJ125WTPLV, SJ150WTPLB, SJ150WTPLT, SJ150WTPLY, SJ200WTPLA, SJ200WTPLG, SJ200 HANDLE
0127055 HANDLE, Remote control JOHNSON
Rating:
38

Buy HANDLE, Remote control 0127055 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$55.95
 

16-04-2019
100 Hundredths Pounds
Johnson Ev: Johnson Evinrude OMC
Johnson Evinrude OMC New OEM Otbd Remote Control Handle, 0327164 0336246 0127055
Color: Black || Sold Each || Please verify your own fitment
$34.27
 

01-03-2018
3120 Hundredths Pounds
NATIONAL N: NATIONAL NAIL
National Nail 1In Eg Rs Round Top Nail 250Ct 0127055
UPC: 042928008447||Weight: 20.800 lbs
Number on catalog scheme: 80
 

BRP JOHNSON entire parts catalog list:

HJ55WMLM 1996
HJ55WMLZ 1997
J125WTPLE 1995
J150WPLEES 1999
J150WPLSIF 2001
J150WPLSSC 2000
J150WTLEOR, J150WTXEOR 1995
J150WTLERC, J150WTLERV, J150WTXERC, J150WTXERV 1994
J200WPXEEN, J200WPXEES 1999
J200WPXSIF 2001
J200WPXSSC 2000
J65WELSIR 2001
J65WELSSC 2000
SJ125WTPLJ, SJ125WTPXJ 1997
SJ125WTPLN, SJ125WTPXN 1998
SJ125WTPLV, SJ125WTPXV 1996
SJ150WTPLB, SJ150WTPXB 1996
SJ150WTPLT, SJ150WTPLT4, SJ150WTPXT, SJ150WTPXT4 1997
SJ150WTPLY, SJ150WTPXY 1998
SJ200WTPLA, SJ200WTPXA 1996
SJ200WTPLG, SJ200WTPXG 1998
SJ200WTPLS, SJ200WTPXS 1997

Information:

(1) Maximum length of pin out of crankshaft face ... 6.4 mm (.25 in.)(2) Thrust plates for center main bearing only.(3) End play for the crankshaft (new) ... 0.13 to 0.50 mm (.005 to .020 in.)Maximum permissible end play with used bearings ... 0.89 mm (.035 in.)(4) Minimum torque for six plugs ... 23 N m (17 lb.ft.) "Stake" (make a mark with a punch) the crankshaft to hold the plug tight.(5) Length of dowel out of the crankshaft ... 4.1 0.5 mm (.16 .02 in.)(6) Maximum permissible temperature of the gear for installation on the crankshaft ... 205° C (400° F) Install gear with timing "V" mark to the outside.(7) 2W1734 Seal Group (rear) installed on rear crankshaft gear.(8) Make reference to CONNECTING ROD BEARINGS.(9) Make reference to MAIN BEARINGS.(10) 2W1733 Seal Group (front). Remove front and rear seal groups as follows: Seals and wear sleeves can not be used again, after the seals and wear sleeves are separated.a. Use the 1P3075 Puller Group to remove the seals.b. Use the 5P7318 Distorter Group to remove the wear sleeves. Install front and rear seal groups as follows:a. Clean the outer surface of the crankshaft with 6V1541 Quick Cure Primer.b. Crankshaft seals must be installed with the lip of the seal toward the inside of the engine as shown. Make sure the correct seal is installed on each end of the crankshaft. Use 2W1733 Seal Group on the front and 2W1734 Seal Group on the rear. No lubrication is needed to install wear sleeves and seals.c. Do not separate seals from sleeves. Install the seal groups as a unit on each end of the engine as shown with the correct tools. See Special Instruction Form Nos. SMHS8508 and SMHS8008 for the necessary tools and complete procedure for installation of front and rear seal groups.Earlier Engine Crankshaft Groups
(1) Maximum length of pin out of crankshaft face ... 6.4 mm (.25 in.)(2) Thrust plates, at center main bearing.(3) End play for the crankshaft (new) ... 0.15 to 0.50 mm (.006 to .020 in.)(4) Minimum torque for six plugs ... 23 N m (17 lb.ft.) "Stake" (make a mark with a punch) the crankshaft to hold the plug tight.(5) Length of dowel out of the crankshaft ... 4.1 0.5 mm (.16 .02 in.)(6) Maximum permissible temperature of the gear for installation on the crankshaft ... 232° C (450° F) Install gear with "V" mark to the outside.(7) Rear gear wear sleeve and seal (on rear crankshaft gear). For removal and installation procedure, see (10).(8) Make reference to CONNECTING ROD BEARING JOURNALS.(9) Make reference to MAIN BEARING JOURNALS.(10) Front wear sleeve and seal: Remove wear sleeves with 5P7318 Distorter Group.Install front and rear wear sleeves and seals as follows:a. Clean the inner surface of the sleeve and the outer surface of the crankshaft (front) or crankshaft gear (rear) with 6V1541 Quick Cure Primer.b. Put 9S3265 Retaining Compound on the cleaned surfaces.c. Install the sleeve and seal at the same time on the crankshaft or crankshaft gear as shown. See Special Instruction Form SMHS7100 for the necessary tools and complete procedure for installation of wear sleeves and seals.


Back to top