0312184 JOHNSON HANDLE,Latch


0312184 HANDLE,Latch JOHNSON 6R69M, 6R70B, 6R71E, 6R72D, 6R73S, 6R74C, 6R75R, 9R69S, 9R70A, 9R71R, 9R72M, 9R73B, CD-25A, LD-13B, MQ-14D HANDLE
0312184 HANDLE,Latch JOHNSON
Rating:
43

Buy HANDLE,Latch 0312184 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

BRP JOHNSON entire parts catalog list:

6R69M, 6RL69M 1969
6R70B, 6RL70B 1970
6R71E, 6R71G, 6RL71E, 6RL71G 1971
6R72D, 6RL72 1972
6R73S, 6RL73S 1973
6R74C, 6RL74C 1974
6R75R, 6RL75R 1975
9R69S, 9RL69S 1969
9R70A, 9R70C, 9RL70A, 9RL70C 1970
9R71R, 9RL71R 1971
9R72M, 9RL72M 1972
9R73B, 9RL73B 1973
CD-25A, CD-25C, CD-25R, CDL-25A, CDL-25C, CDL-25R 1968
LD-13B, LD-13E, LD-13M, LDL-13B, LDL-13E, LDL-13M 1968
MQ-14D, MQ-14E, MQL-14D, MQL-14E 1968

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     268-1968     Pry Bar     1    Start By:
Remove the valve mechanism cover.
Remove the fuel injection line.
Illustration 1 g01264292
Illustration 2 g01264293
Note: Do not remove the quill tube. This action will reduce the risk of contamination to the system.
Fully loosen quill tube nut (1). Pull quill tube (1) out of the bore until you see O-ring seal (2). This action will ensure that the injector does not contact the quill tube during removal. At this time, inspect O-ring seal (2) for wear or for damage. Replace the O-ring seal if necessary.
Illustration 3 g02161166
Typical Example
Disconnect harness assembly (3) from the unit injector.
Illustration 4 g02161316
Typical Example
Remove bolt (5) from clamp (6) .Note: When possible, remove the unit injector by hand by twisting the unit injector and pulling upward. Be sure not to strike the unit injector during the removal procedure.
If unit injector (4) cannot be removed by hand, go to Step 5.
Illustration 5 g02161361
Typical ExampleNote: Do not damage the unit injector during removal. Side loading may damage to the unit injector.
Position Tooling (A) under unit injector clamp (6). Carefully remove unit injector (4) from the cylinder head.Installation Procedure
Table 2
Required Tools    
Tool     Part Number     Part Description     Qty    
B     -     Scotch Brite     1    
C     1U-5718     Vacuum Pump     1    
169-7372 Bottle Assembly     1    
4C-4057 Clear Plastic Tubing
7.92 mm (0.312 inch) OD     1    
4C-4055 Clear Plastic Tubing
6.35 mm (0.250 inch) OD        
D     9U-5470     Reamer     1    
E     4C-6161     Tube Brush     1    
F     9U-6862     Tapered Brush     1    
G     4C-6774     Vacuum Gun Kit     1    
H     4C-5027     Tap Wrench     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Evacuate as much fuel and oil as possible from the cylinder head before installing the unit injector. Several evacuations may be necessary. Use Tooling (C) to remove the fuel and oil from the cylinder.Note: Tooling (F) is available to clean loose material from the sleeve bore and the cylinder.
Clean the carbon from the sleeve, the sleeve bore, and the end of the unit injector. Clean the carbon from the seat area that is inside of the cylinder head. A fine grade of Tooling (B) is preferred. Clean the carbon from the cylinder head. If the sleeve of the unit injector has been removed, use Tooling (D) to remove only carbon from the surface of the sleeve. If the sleeve of the unit injector is installed, use Tooling (E) to clean the carbon deposit from the inside of the sleeve.The following procedure is the preferred method of cleaning the sleeve bore.Place a 38 mm (1.5 inch) square piece of Scotch Brite material on the end of Tooling (F). Twist Tooling (F) with Tooling (H) against the lower surface of the sleeve bore.The surface should be cleaned until the surface is smooth and shiny. The entire sleeve bore should be cleaned in order to remove any loose carbon particles.Note: Tooling (G) is available to clean loose material from the sleeve bore and the cylinder.


Parts handle JOHNSON:

0313154
 
0313154 HANDLE
10E74G, 15E74G, 50ES72C, 50ES73R, 50R79C, 55E79C, 6R69M, 6R70B, 6R71E, 6R72D, 6R73S, 6R74C, 9R69S, 9R70A, 9R71R, 9R72M, 9R73B, CD-25A, LD-13B, MQ-14D
0312858
 
0312858 HANDLE, Steering, inner half
20R69B, 20R70C, 20R71S, 20R72R, 20R73A, 25E72R, 25E73A, 25E74M, 25R69B, 25R70C, 25R71S, 6R69M, 6R70B, 6R71E, 6R72D, CD-25A, FD-22A
0312859
 
0312859 HANDLE, Steering, outer half
20R69B, 20R70C, 25R69B, 25R70C, 6R69M, 6R70B, CD-25A, FD-22A
0309732
 
0309732 HANDLE,Carrying
9R69S, 9R70A, 9R71R, 9R72M, 9R73B, MQ-14D
0315939
 
0315939 HANDLE, Strg., outer half
20R71S, 20R72R, 25E72R, 25R71S, 6R71E, 6R72D
0385837
 
0385837 HANDLE, Gearshift
6R73S, 6R74C, 6R75R, 6R76A, 6R77M, 6R78B
0318213
 
0318213 HANDLE, Strg. inner half
25E75B, 25E76E, 25E77S, 35E76G, 35E77C, 6R73S, 6R74C, 6R75R, 6R76A, 6R77M, 6R78B, 6R79E
Back to top