0398736 JOHNSON HANDLE, Steering

Table 1
Diagnostic Trouble Codes for the Data Link Configuration Status
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
639-14 247-14 J1939 Network #1 : Special Instruction The data received from the CAN A data bus is not in the correct format.
The code is logged.
1235-14 5856-14 J1939 Network #3 : Special Instruction The data received from the CAN C data bus is not in the correct format.
The code is logged.
3360–14 3820–14 Aftertreatment #1 DEF Controller : Special Instruction The data received from the DCU is not in the correct format.
The warning lamp is illuminated.
5576-14 3468-14 Aftertreatment #1 Identification : Special Instruction The data received from the aftertreatment ID module is not in the correct format.
The code is logged.
5588-14 E1132 (2) Proprietary Network #2 : Special Instruction The data received from the DCU is incompatible.
The warning lamp will come on.
The code is logged. Complete the procedure in the order in which the steps are listed.
Table 2
Troubleshooting Test Steps Values Results
1. Check for an Associated -9 Code
A. Establish communication between the electronic service tool and the Electronic Control Module (ECM) for the engine.
B. Download a "Warranty Report" from the engine ECM before troubleshooting or clearing diagnostic trouble codes.
C. Check for active diagnostic codes.
Associated Trouble code
Result: An associated -9 code is logged.
Repair: Repair all associated -9 codes before continuing with this procedure. Refer to Troubleshooting, "CAN Data Link - Test".
If a -14 code is still present after resolving the -9 code, proceed to Test Step 2.
Result: An associated -9 code is not logged.
Proceed to Test Step 2.
2. Check the Personality Module Code for Compatibility with the Application
A. Connect to the electronic service tool.
B. Select the ECM connection that is related to the logged code.
C. Check if the personality module code is valid for the application.
Compatible personality module
Result: The code is valid for the application.
Proceed to Test Step 3.
Result: The code is not valid for the application.
Repair: Obtain the correct flash file and update the ECM. Reset all active codes and clear all logged codes. Return the unit to service.
3. Check that the latest available software is installed and there are no applicable Technical Information Bulletins or Special Instruction documentation released
A. Ensure that the latest software is installed on the engine ECM.
B. Ensure that the latest software is installed on the Dosing Control Unit (DCU)
If necessary, refer to Troubleshooting, "ECM Software - Install" for the correct procedure.
C. Ensure all Technical Information Bulletins and/or Special Instruction documented for the issue and/or product are reviewed and followed.
D. Ensure that the software installed is for the correct system voltage (12 V or 24 V).
If necessary, refer to Troubleshooting, "ECM Software - Install" for the correct procedure.
Software and Publications
Result: The latest software is not installed.
Repair: Install the latest engine ECM software and then install the latest DCU software. If necessary, refer to Troubleshooting, "ECM Software - Install" for the correct procedure.
Start the engine and wait for 2 minutes.
If the fault is cleared, return the engine to service.
If the fault is still present, proceed to Test Step 2.
Result: Applicable Technical Information Bulletin/Special Instruction publication is available.
Repair: Review and follow instructions provided in the available publication.
Result: The latest software is installed.
Proceed to Test Step 4.
4. Check the Configuration Parameters
A. Check the configuration parameters to ensure that the parameters are programmed correctly. Refer to Troubleshooting, "Configuration Parameters".
B. Select the ECM connection that is related to the logged code.
Correct configuration parameters
Result: The configuration parameters are programmed correctly.
Proceed to Test Step 5.
Result: The configuration parameters are not programmed correctly.
Repair: Program the parameters to function with the other modules on the data link. Reset all active codes and clear all logged codes. Return the unit to service.
5. Check for Compatibility with Any Other ECM on the Data Link
A. Use the as shipped information found in SIS web TMI to determine if any other ECM or display on the data link are incompatible.
B. Select the ECM connection that is related to the logged code.
Compatible ECM
Result: The ECMs are not compatible.
Repair:Replace the incompatible ECM with the correct module. Reset all active codes and clear all logged codes. Return the unit to service.
If the procedure did not correct the fault, contact the Dealer Solutions Network (DSN).