0327414 HOSE, Pump to tee JOHNSON
J35AELCDE, J40ECDE, J40ECOB, J40ECRM, J45RCCDS, J45RCCUC, J50BECDE, J50BECIC, J50BECNR, J50BECOB, J50BECRM, J50BECTA, J55RCIM, J55RSLN, J55RWLCDC, J55RWLCOS, J55RWLCRD, J55RWLCUC, J60ECIA, J60ECNM, J60ECTB, J60ELCOD, J60ELCRE, R55RWLR, S45RCLR
HOSE
Price: query
Compatible models:
BRP JOHNSON entire parts catalog list:
- FUEL PUMP AND FILTER » 0327414
J40ECOB, J40ELCOB, J40RCOB, J40RLCOB, J40TECOB, J40TELCOB 1985
J40ECRM, J40ELCRM, J40RCRM, J40RLCRM, J40TECRM, J40TELCRM 1984
J45RCCDS, J45RCLCDS 1986
J45RCCUC, J45RCLCUC 1987
J50BECDE, J50BELCDE, J50TELCDE, J50TLCDE 1986
J50BECIC, J50BELCIC 1981
J50BECNR, J50BELCNR 1982
J50BECOB, J50BELCOB, J50TELCOB, J50TLCOB 1985
J50BECRM, J50BELCRM, J50TELCRM, J50TLCRM 1984
J50BECTA, J50BELCTA, J50TELCTA 1983
J55RCIM, J55RLCIM 1981
J55RSLN, J55RSLN-2, J55RSN, J55RSN-2, J55RSYN, J55RSYN-2 1983
J55RWLCDC 1986
J55RWLCOS 1985
J55RWLCRD 1984
J55RWLCUC 1987
J60ECIA, J60ECIH, J60ELCIA, J60ELCIH, J60TLCIA, J60TLCIH 1981
J60ECNM, J60ELCNM, J60TLCNM 1982
J60ECTB, J60ELCTB, J60TLCTB 1983
J60ELCOD, J60TLCOD 1985
J60ELCRE, J60TLCRE 1984
R55RWLR 1988
S45RCLR, S45RCR 1988
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6640 Sealant 1
B - Guide Studs
M8 by 80 mm 2
C 319-6486 Alignment Tool 1
- Bolts
M10 by 50 mm 3
D 1U-6396 O-Ring Assembly Compound 1
E 7M-7456 Bearing Mount Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the wiring harness assembly is correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness and the convoluting.
Ensure that the front housing is clean and free from damage. If necessary, replace the front housing. If necessary, install blanking plugs to a new front housing. Use Tooling (A) in order to seal all D-plugs.
Clean all the gasket surfaces of the cylinder block.
Illustration 1 g02490396
Illustration 2 g02490397
Inspect dowel (17) and dowel (18) for damage. If necessary, replace the dowels in the cylinder block.
Install thrust washer (15) into the recess in cylinder block (16). Refer to Disassembly and Assembly, "Camshaft - Install" for more information.
Install Tooling (B) to cylinder block (16). Refer to Illustration 2.
Align a new gasket (10) with Tooling (B). Install the gasket to (16) cylinder block. Note: Ensure that two circular Tabs (X) on the gasket are engaged in two Holes (Y) in cylinder block (16). Ensure that dowel (18) in cylinder block (16) is engaged on the gasket.
Install Tooling (C) to cylinder block (16).
Illustration 3 g02490399
If necessary, follow Step 8.a through Step 8.c in order to install bearing (10) to housing (7).
Apply a small continuous bead of Tooling (E) to outer Surface (Z) of bearing (10).
Place housing (7) onto a suitable support.
Use a suitable tool in order to press bearing (10) into housing (7) until the bearing is in the correct position within the housing. Remove any excess bearing mount compound.
Install the front housing over Tooling (B) and Tooling (C) onto cylinder block (16).
Illustration 4 g02490400
(11) M8 by 35 mm
(12) M8 by 20 mm
(13) M8 by 25 mm
Illustration 5 g02058297
Install bolts (13) to front housing (7) finger tight.
Remove Tooling (B).
Loosely install bolts (11) and bolts (12). Refer to Illustration 4 for the correct position of the bolts.
Tighten bolts (11), bolts (12) and bolts (13) in the sequence that is shown in Illustration 5 to a torque of 28 N m (248 lb in).
Remove Tooling (C) from the cylinder block.
Illustration 6 g02490356
Install a new O-ring seal (8) and a new O-ring seal (9) to bypass tube (5). Use Tooling (D) in order to lubricate the O-ring seals.
Install bypass tube (5) to the cylinder head. Install bolts (6). Tighten the bolts to a torque of 9 N m (80 lb in).
Connect harness assembly (2) to coolant temperature sensor (3).
Slide locking tab (1) (not shown) into the locked position.
Position harness assembly (2) onto bypass tube (5). Install a new cable strap (4). Note: Ensure that the cable strap meets Original Equipment Manufactures (OEM) specification.End By:
Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump - Install" for the correct procedure.
Install the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) - Install" for the correct procedure.
If the engine has an accessory drive, install the accessory drive. Refer to Disassembly and Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
Install the engine oil pan . Refer to Disassembly and Assembly, "Engine Oil Pan - Install" for the correct procedure.
Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Install" for the correct procedure.
Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install" for the correct procedure.
Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the correct procedure.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Fill" for the correct procedure.
Parts hose JOHNSON:
0305871
0305871 HOSE,Fuel tank to primer bulb
100ESL71A, 100ESL72R, 100ML79S, 10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78
0320417
0320417 HOSE, Large
100ML79S, 10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 25E74M, 25E75B, 25E76E, 25E
0386940
0386940 HOSE & PRIMER BULB ASSY.
100ML79S, 10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 25E74M, 25E75B, 25E76E, 25E
0322172
0322172 HOSE,Overboard pump indicator
25E77S, 25E78C, 25E79R, 35E76G, 35E77C, 35E78R, 35E79A, 50R79C, 55E78S, 55E79C, 70EL78C, 70EL79R, 75ELR78C, 75ELR79R, J25ECIB, J25RCSA, J25RSA, J35ECIG, J35ECSM, J50BECIC, J50ECSR, J55RCIM, J55RLCSA, J5RCIC, J5RCSS, J60ECIA, J60ECSR, J70ELCIH, J70ELC
0320947
0320947 HOSE,Fuel pump lower to tee
100ML79S, 115EL77S, 115ETZ78C, 115ML79R, 115TXL77S, 140ML77S, 140ML78C, 140ML79R, 150TL79C, 175TL79R, 200TL76S, 200TL79A, 235TL70A, 85EL77S, 85ETLR78C, 85ML79R, 85TXLR77S, J35AELCDE, J40ECDE, J50BECDE, J65WMLCOC, J70ELCOS, J75ECOS
0327417
0327417 HOSE, Pump to tee
J40ECOB, J50BECOB, J60ELCOD, J65RWLCDR, J65RWLCOC, J65RWLCRS, J65WMLCOC, J70ELCIH, J70ELCNB, J70ELCRD, J70ELCTE, J75ECNB, J75ECRD, J75ECTE, J75ERCIH
0396940
0396940 HOSE & PRIMER BULB ASSY.
J115MLCRD, J140TLCRD, J35AELCDE, J35AELCUD, J40AELCCS, J40ECDE, J40ECUD, J48ESLCCC, J48ESLCCC, J48ESLCUS, J48ESLCUS, J50BECCS, J50BECDE, J50BECUD, J90MLCRD
0329604
0329604 HOSE, Connector to elbow 2-3/4" long
J150STLCOH, J150STLCRD, J150TLCOS, J150TLCRD, J155WTLCOC, J175TLCOC, J185TLCOC, J185TLCRS, J235STLCOR, J235STLCRC, J235TLCOR, J235TLCRC, J35AELCDE, J40ECDE, J50BECDE