0552215 JOHNSON HOSE,Conn. to pump


0552215 HOSE,Conn. to pump JOHNSON 4R69B, JH-23A HOSE
0552215 HOSE,Conn. to pump JOHNSON
Rating:
43

Buy HOSE,Conn. to pump 0552215 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 54
 

Compatible models:

4R69B   JH-23A   JOHNSON

BRP JOHNSON entire parts catalog list:

4R69B, 4W69B, 4WF69B 1969
JH-23A, JH-23M, JHF-23A, JHF-23M, JHFL-23A, JHFL-23M, JHL-23A, JHL-23M, JW-23A, JW-23M, JWF-23A, JWF-23M, JWFL-23A, JWFL-23M, JWL-23A, JWL-23M 1968

Information:

Start By:a. remove valve covers 1. Remove bolts (1) that hold the valve cover bases to the cylinder head assembly. Remove valve cover bases (2). 2. Use tool (A) to loosen fuel injection line (3) from fuel injection nozzle (4). 3. Use tool (B) to loosen the nut at the fuel injection line adapter end. Remove inner fuel injection lines (3). Install caps and plugs on all fuel injection line openings to keep dirt out of the fuel system. 4. Remove bolts (5) that hold the rocker shaft assemblies to the cylinder head assembly.5. Remove rocker shaft assemblies (6). 6. Put identification marks on the push rods as to their location in the engine. Remove push rods (7). 7. Put identification marks on the bridges as to their location in the engine. Remove bridges (8) from the dowels on the cylinder head assembly.Install Rocker Shaft Assemblies And Push Rods
1. Put clean engine oil on the bridges and dowels. Install the original bridges in their respective locations. New bridges can be mixed.2. Install bridges (8) on the bridge dowels. While firmly pressing 0.5 to 4.5 kg (1 to 10 lb.) straight down on the top contact surface of the bridge, turn the adjusting screw clockwise until contact is made with the valve stem. Turn the screw an additional 20° to 30° (1/3 to 1/2 of 1 hex on nut). This will straighten the dowel in the guide and compensate for the slack in the threads. Hold the adjusting screw in this position, and tighten the locknut to a torque of 30 4 N m (22 3 lb.ft.). Install original push rods in their respective locations in the engine. New push rods can be mixed.3. Install push rods (7). 4. Put rocker shaft assemblies (6) in position on the cylinder head assembly.5. Put clean engine oil on the threads of bolts (5) that hold the shaft assemblies in place. Tighten the bolts first to a torque of 270 25 N m (200 18 lb.ft.). Start with the bolt in the center of the rocker shaft assembly. Tighten the bolts again to a torque of 450 20 N m (330 15 lb.ft.). Tighten the bolts again by hand to a torque of 450 20 N m (330 15 lb.ft.).
Do not cause damage to the O-ring seals on the inner fuel lines.
6. Install inner fuel injection lines (3). Tighten the fuel injection line adapter nuts (9) to a torque of 40 7 N m (30 5 lb.ft.) with tool (B).7. Tighten fuel injection line nut (10) to a torque of 40 7 N m (30 5 lb.ft.) with tool (A).8. Make adjustments to the valves until the intake valve clearance is 0.38 mm (.015 in.) and the exhaust valve clearance is 0.76 mm (.030 in.). See Valve Clearance Setting in Testing And Adjusting. Tighten the locknut to a torque of 30 4 N m (22 3 lb.ft.) and check the adjustments. 9. Install valve cover bases (2) on the cylinder head assembly. Install bolts that hold the valve cover bases in place. Tighten bolts (1) to a torque of 14 3 N m (10 2 lb.ft.).End By:a. install valve covers


Parts hose JOHNSON:

0305871
 
0305871 HOSE,Fuel tank to primer bulb
100ESL71A, 100ESL72R, 100ML79S, 10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78
0312822
 
0312822 HOSE,Primer bulb to fuel connector
4R69B, 4R70E, 4R71D, 4R72S, 4R73C, 4R74R, JH-23A, LD-13B
0302657
 
0302657 HOSE,Pump to carb.
4R69B, 4R70E, JH-23A
Back to top