5005096 **KIT, Clutch Shaft Retainer JOHNSON
J150CXSDE, J150CXSNF, J150CXSOB, J150CXSRM, J150CXSTA, J150GLSTA, J175CXSDE, J175CXSNF, J175CXSOB, J175CXSRM, J175CXSTA, J175GLSTA
KIT

Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- GEARCASE - CX, MODELS » 5005096
J150CXSOB 2004,2005
J150CXSRM 2004
J150CXSTA 2003
J150GLSTA, J150PLSTM, J150PXSTM 2003
J175CXSDE 2006
J175CXSNF, J175PLSNF, J175PXSNF, J175VLSNF 2002
J175CXSOB 2004,2005
J175CXSRM 2004
J175CXSTA 2003
J175GLSTA, J175PLSTM, J175PXSTM 2003
Information:
Introduction
Do not perform any procedure in this Special Instruction until you read this information and you understand this information.In a crankcase ventilation system, the fumes from the crankcase are filtered before the fumes are sent to the air intake system. Steps must be taken in order to prevent oil from collecting on the components of the air intake system. Otherwise, the following problems can result:
Decreased service life of air cleaner filters
Premature plugging of the aftercooler coreRecommendations
Route the fumes from the crankcase through a commercially available aftermarket fumes disposal system. Direct the filtered fumes to the dirty side of the air cleaner filter elements.Install soot filters on the air cleaner filter elements.Monitor the differential pressure of the air intake system in order to determine when the system requires servicing.Soot Filters
Soot filters fit firmly around 490 mm (19.3 inch) filter elements. Table 1 lists the part number and the height of the soot filters.
Table 1
Soot Filters
Part Number of the Soot Filter Height of the Soot Filter
8N-2555
250 mm (10 inch)
115-3634
350 mm (14 inch)
115-3635
450 mm (18 inch) The soot filter can be cleaned in order to remove oil. Wash the filter in a solution of soap and water. Allow the filter to dry completely before installing the filter.Monitoring the Differential Pressure
A differential pressure gauge can be installed across the air side of the aftercooler core. The differential pressure provides an indication of the amount of plugging in the aftercooler core. The 152-2067 Oil Filter Pressure Differential Gauge Gp is suitable for monitoring the differential pressure. Table 2 lists the components and the locations for connecting the differential pressure gauge.
Table 2
Components and Locations for Sensing the Differential Pressure
Type of Air Intake System Hose Fittings Location for the Fittings
Mechanical Unit Injection (MUI)
Rear Turbocharger 5P-1519 Hose and internal 37 degree flare fitting ends 5J-7303 Elbow
8B-2664 Reducer Bushing
001-9440 Connector Refer to Illustration 1 and Illustration 2
MUI
Top Turbocharger 5J-7303 Elbow
8B-2664 Reducer Bushing
001-9440 Connector Refer to Illustration 3 and Illustration 4
Electronic Unit Injection (EUI)
Rear Turbocharger 001-9440 Connector (1) Refer to Illustration 4
EUI
Top Turbocharger 001-9440 Connector (1) Refer to Illustration 5
( 1 ) Two Connectors are required
Illustration 1 g01446694
Typical configuration (1) Location for the 5J-7303 Elbow for the high pressure port
Illustration 2 g01446714
Port on a cylinder block (2) Location for the 8B-2664 Reducer Bushing and 001-9440 Connector for the low pressure port
Illustration 3 g01446657
Typical configuration (3) Location for the 5J-7303 Elbow for the high pressure port
Illustration 4 g01446721
Typical configuration (4) Location for the 001-9440 Connector for the low pressure port (5) Location for the 001-9440 Connector for the high pressure port
Illustration 5 g01446991
Typical configuration (6) Location for the 001-9440 Connector for the high pressure port (7) Location for the 001-9440 Connector for the low pressure portTable 3 provides the maximum allowable differential pressure across various components. Perform the appropriate service procedure if the differential pressure exceeds the value that is listed.
Table 3
Maximum Differential Pressure and Service Procedures
Component Maximum Differential Pressure Service Procedure
Aftercooler Core
7.5 kPa (30 inches of H2O) Clean the aftercooler core.
Air Cleaner Filter
6.2 kPa (25 inches of H2O) Clean the soot filter.
Replace the air cleaner filter, if necessary.
Crankcase The crankcase pressure must be within
0.5 kPa (
Do not perform any procedure in this Special Instruction until you read this information and you understand this information.In a crankcase ventilation system, the fumes from the crankcase are filtered before the fumes are sent to the air intake system. Steps must be taken in order to prevent oil from collecting on the components of the air intake system. Otherwise, the following problems can result:
Decreased service life of air cleaner filters
Premature plugging of the aftercooler coreRecommendations
Route the fumes from the crankcase through a commercially available aftermarket fumes disposal system. Direct the filtered fumes to the dirty side of the air cleaner filter elements.Install soot filters on the air cleaner filter elements.Monitor the differential pressure of the air intake system in order to determine when the system requires servicing.Soot Filters
Soot filters fit firmly around 490 mm (19.3 inch) filter elements. Table 1 lists the part number and the height of the soot filters.
Table 1
Soot Filters
Part Number of the Soot Filter Height of the Soot Filter
8N-2555
250 mm (10 inch)
115-3634
350 mm (14 inch)
115-3635
450 mm (18 inch) The soot filter can be cleaned in order to remove oil. Wash the filter in a solution of soap and water. Allow the filter to dry completely before installing the filter.Monitoring the Differential Pressure
A differential pressure gauge can be installed across the air side of the aftercooler core. The differential pressure provides an indication of the amount of plugging in the aftercooler core. The 152-2067 Oil Filter Pressure Differential Gauge Gp is suitable for monitoring the differential pressure. Table 2 lists the components and the locations for connecting the differential pressure gauge.
Table 2
Components and Locations for Sensing the Differential Pressure
Type of Air Intake System Hose Fittings Location for the Fittings
Mechanical Unit Injection (MUI)
Rear Turbocharger 5P-1519 Hose and internal 37 degree flare fitting ends 5J-7303 Elbow
8B-2664 Reducer Bushing
001-9440 Connector Refer to Illustration 1 and Illustration 2
MUI
Top Turbocharger 5J-7303 Elbow
8B-2664 Reducer Bushing
001-9440 Connector Refer to Illustration 3 and Illustration 4
Electronic Unit Injection (EUI)
Rear Turbocharger 001-9440 Connector (1) Refer to Illustration 4
EUI
Top Turbocharger 001-9440 Connector (1) Refer to Illustration 5
( 1 ) Two Connectors are required
Illustration 1 g01446694
Typical configuration (1) Location for the 5J-7303 Elbow for the high pressure port
Illustration 2 g01446714
Port on a cylinder block (2) Location for the 8B-2664 Reducer Bushing and 001-9440 Connector for the low pressure port
Illustration 3 g01446657
Typical configuration (3) Location for the 5J-7303 Elbow for the high pressure port
Illustration 4 g01446721
Typical configuration (4) Location for the 001-9440 Connector for the low pressure port (5) Location for the 001-9440 Connector for the high pressure port
Illustration 5 g01446991
Typical configuration (6) Location for the 001-9440 Connector for the high pressure port (7) Location for the 001-9440 Connector for the low pressure portTable 3 provides the maximum allowable differential pressure across various components. Perform the appropriate service procedure if the differential pressure exceeds the value that is listed.
Table 3
Maximum Differential Pressure and Service Procedures
Component Maximum Differential Pressure Service Procedure
Aftercooler Core
7.5 kPa (30 inches of H2O) Clean the aftercooler core.
Air Cleaner Filter
6.2 kPa (25 inches of H2O) Clean the soot filter.
Replace the air cleaner filter, if necessary.
Crankcase The crankcase pressure must be within
0.5 kPa (
Parts kit JOHNSON:
0434153
0434153 KIT, Propeller parts
J115GLSDE, J115PLSDA, J115PXSDA, J115PXSOR, J115WPLSOC, J150CXSDE, J150CXSOB, J150GLSDE, J150GLSOB, J150PLSDD, J150PLSOE, J150PXSDD, J150PXSOE, J150WPLEES, J150WTLEOR, J175CXSDE, J175CXSOB, J175GLSDE, J175GLSOB, J175PLSDD, J175PLSOE, J175PXSDD, J175P