0125198 KNOB, Binnacle, center JOHNSON
J120TLAEM, J120TLASB, J120TLCCA, J140CXCCS, J140CXCEC, J140CXESR, J150CXCCA, J150CXCEM, J150CXESB, J175STLACM, J175STLCEB, J175STLESE, J185ESXESS, J185ESXW, J200CXCCR, J200CXCEA, J200CXESM, J225CXCCE, J225CXCED, J225CXESS, J275CXCCA, J300CXCCA, J300C
KNOB
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
J120TLASB, J120TLESB, J120TXESB, VJ120TLASB, VJ120TLESB, VJ120TXESB 1990
J120TLCCA, J120TXCCA 1988
J140CXCCS, J140TLCCM, J140TXCCM 1988
J140CXCEC, J140TLAEB, J140TLCEB, J140TXCEB 1989
J140CXESR, J140TLASE, J140TLESE, J140TXESE, VJ140TLASE, VJ140TLESE, VJ140TXESE 1990
J150CXCCA, J150TLCCA, J150TXCCA 1988
J150CXCEM, J150TLAEM, J150TLCEM, J150TXCEM, TJ150TXCEM 1989
J150CXESB, J150TLASB, J150TLESB, J150TXESB, VJ150TLESB, VJ150TXESB 1990
J175STLACM, J175STLCCM, J175TLCCM, J175TXCCM 1988
J175STLCEB, J175TXCEB 1989
J175STLESE, J175TXESE, VJ175SLESE, VJ175TXESE 1990
J185ESXESS 1990
J185ESXW 1989
J200CXCCR, J200STLACM, J200STLCCM, J200TXCCR 1988
J200CXCEA, J200STLCEB, J200TXCEA, TJ200TXCEA 1989
J200CXESM, J200STLESE, J200TXESM, VJ200SLESE, VJ200TXESM 1990
J225CXCCE, J225PLCCE, J225PXCCE, J225TLCCE, J225TXCCE 1988
J225CXCED, J225PLAED, J225PLCED, J225PXCED, J225TLAED, J225TLCED, J225TXCED 1989
J225CXESS, J225PLASS, J225PLESS, J225PXESS, J225TLASS, J225TLESS, J225TXESS, VJ225PLESS, VJ225PXESS, VJ225TLASS, VJ225TLESS, VJ225TXESS 1990
J275CXCCA, J275PLCCA, J275PXCCA 1988
J300CXCCA, J300PLCCA, J300PXCCA 1988
J300CXCEM, J300PLCEM, J300PXCEM 1989
J300CXESB, J300PLESB, J300PXESB 1990
Information:
Note: The following clamps and bellows are one-time use components. Discard the components after removal and install new components.
Illustration 1 g02790637
Engine was not illustrated for photographic purposes.
Note: Note the orientation of clamps (2). If installed incorrectly, the clamps will damage the heat shields.
Loosen clamps (2). Remove bolts (4) and any spacers.
Remove exhaust manifold (3) and remove bellows (1) and the gaskets. Remove gasket (5) from exhaust manifold (3).
Repeat Step 1 and Step 2 for the next four exhaust manifolds. Repeat for the other side.
Illustration 2 g02790688
Engine was not illustrated for photographic purposes.
Note: Note the orientation of clamps (8) and (11). If installed incorrectly, the clamps will damage the heat shields.
Loosen clamps (11) and (8). Remove bolts (13) and any spacers.
Remove exhaust manifold (12). Remove bellows (9) and (10) and the gaskets. Remove gasket (14) from exhaust manifold (12).Note: The only gasket for bellows (10) will be located on the exhaust manifold side of the bellows. Note the orientation of bellows (10) for installation. The air flow direction is from the exhaust manifold to the turbocharger.
Repeat Step 4 and Step 5 for the other side.Note: Some engine arrangements are equipped with a cap in place of adapter (7) for the exhaust bypass valve. If so, the following step can be ignored.
Remove bolts (6) and adapter (7). Remove the gasket from adapter (7).Installation Procedure
Note: The following clamps and bellows are one-time use components. Discard the components after removal and install new components.
Illustration 3 g02790688
Engine was not illustrated for photographic purposes.
Note: Some engine arrangements are equipped with a cap in place of adapter (7) for the exhaust bypass valve. If so, the following step can be ignored.
Position adapter (7) and install bolts (6). Tighten bolts (6) to a torque of 55 5 N m (41 4 lb ft).Note: Clamps (11) and (8) are to be orientated horizontally with the threaded rods pointing outward from the engine. Note the orientation noted when removed.Note: Ensure that the gaskets for bellows (9) and (10) are seated correctly with the tabs properly positioned. If the gaskets slide out of position, check that section of the exhaust manifold for damage and replace if there is damage.
Install the gaskets for bellows (9) and (10) and install bellows (9) and (10). Position clamps (11) and (8) horizontally.Note: Note the orientation of bellows (10) with the direction of air flow.
Seat gasket (14) onto exhaust manifold (12). Install exhaust manifold (12).
Install the spacers and bolts (13). Tighten to a torque of 55 5 N m (41 4 lb ft). Retighten to a torque of 55 5 N m (41 4 lb ft).
Check the final position of clamps (8) and (11). Tighten clamps (11) to a torque of 7.5 1 N m (66.38 8.85 lb in). Tighten clamps (8) to a torque of 17 2 N m (150.5 17.7 lb in).
Repeat Step 2 through Step 5 for the other side.
Illustration 4 g02790637
Engine was not illustrated for photographic purposes.
Note: Clamps (2) are to be orientated horizontally with the threaded rods pointing outward from the engine. Note the orientation noted when removed.Note: Ensure that the gaskets for bellows (1) are seated correctly with the tabs properly positioned. If the gaskets slide out of position, check that section of the exhaust manifold for damage and replace if there is damage.
Seat gasket (5) onto exhaust manifold (4).
Position exhaust manifold (4). Install the spacers and bolts (4). Tighten to a torque of 55 5 N m (41 4 lb ft). Retighten to a torque of 55 5 N m (41 4 lb ft).
Check the final position of clamps (2). Tighten clamps (2) to a torque of 12 N m (106 lb in).
Repeats Step 7 through Step 9 for the remaining exhaust manifolds. Repeat for the other side.
Refer to the following checks after installation:
Confirm that all the clamps are orientated horizontally and the rods pointing outwards from the engine.
Confirm that each clamp has a uniform gap. If not, ensure that the gasket for each joint is seated correctly.
Check that the bellows are aligned correctly.
Use the above procedures to correct any issues that are found in the above checks.End By:
Install the air inlet manifold. Refer to Disassembly and Assembly, "Air Inlet Manifold - Remove and Install".
Illustration 1 g02790637
Engine was not illustrated for photographic purposes.
Note: Note the orientation of clamps (2). If installed incorrectly, the clamps will damage the heat shields.
Loosen clamps (2). Remove bolts (4) and any spacers.
Remove exhaust manifold (3) and remove bellows (1) and the gaskets. Remove gasket (5) from exhaust manifold (3).
Repeat Step 1 and Step 2 for the next four exhaust manifolds. Repeat for the other side.
Illustration 2 g02790688
Engine was not illustrated for photographic purposes.
Note: Note the orientation of clamps (8) and (11). If installed incorrectly, the clamps will damage the heat shields.
Loosen clamps (11) and (8). Remove bolts (13) and any spacers.
Remove exhaust manifold (12). Remove bellows (9) and (10) and the gaskets. Remove gasket (14) from exhaust manifold (12).Note: The only gasket for bellows (10) will be located on the exhaust manifold side of the bellows. Note the orientation of bellows (10) for installation. The air flow direction is from the exhaust manifold to the turbocharger.
Repeat Step 4 and Step 5 for the other side.Note: Some engine arrangements are equipped with a cap in place of adapter (7) for the exhaust bypass valve. If so, the following step can be ignored.
Remove bolts (6) and adapter (7). Remove the gasket from adapter (7).Installation Procedure
Note: The following clamps and bellows are one-time use components. Discard the components after removal and install new components.
Illustration 3 g02790688
Engine was not illustrated for photographic purposes.
Note: Some engine arrangements are equipped with a cap in place of adapter (7) for the exhaust bypass valve. If so, the following step can be ignored.
Position adapter (7) and install bolts (6). Tighten bolts (6) to a torque of 55 5 N m (41 4 lb ft).Note: Clamps (11) and (8) are to be orientated horizontally with the threaded rods pointing outward from the engine. Note the orientation noted when removed.Note: Ensure that the gaskets for bellows (9) and (10) are seated correctly with the tabs properly positioned. If the gaskets slide out of position, check that section of the exhaust manifold for damage and replace if there is damage.
Install the gaskets for bellows (9) and (10) and install bellows (9) and (10). Position clamps (11) and (8) horizontally.Note: Note the orientation of bellows (10) with the direction of air flow.
Seat gasket (14) onto exhaust manifold (12). Install exhaust manifold (12).
Install the spacers and bolts (13). Tighten to a torque of 55 5 N m (41 4 lb ft). Retighten to a torque of 55 5 N m (41 4 lb ft).
Check the final position of clamps (8) and (11). Tighten clamps (11) to a torque of 7.5 1 N m (66.38 8.85 lb in). Tighten clamps (8) to a torque of 17 2 N m (150.5 17.7 lb in).
Repeat Step 2 through Step 5 for the other side.
Illustration 4 g02790637
Engine was not illustrated for photographic purposes.
Note: Clamps (2) are to be orientated horizontally with the threaded rods pointing outward from the engine. Note the orientation noted when removed.Note: Ensure that the gaskets for bellows (1) are seated correctly with the tabs properly positioned. If the gaskets slide out of position, check that section of the exhaust manifold for damage and replace if there is damage.
Seat gasket (5) onto exhaust manifold (4).
Position exhaust manifold (4). Install the spacers and bolts (4). Tighten to a torque of 55 5 N m (41 4 lb ft). Retighten to a torque of 55 5 N m (41 4 lb ft).
Check the final position of clamps (2). Tighten clamps (2) to a torque of 12 N m (106 lb in).
Repeats Step 7 through Step 9 for the remaining exhaust manifolds. Repeat for the other side.
Refer to the following checks after installation:
Confirm that all the clamps are orientated horizontally and the rods pointing outwards from the engine.
Confirm that each clamp has a uniform gap. If not, ensure that the gasket for each joint is seated correctly.
Check that the bellows are aligned correctly.
Use the above procedures to correct any issues that are found in the above checks.End By:
Install the air inlet manifold. Refer to Disassembly and Assembly, "Air Inlet Manifold - Remove and Install".
Parts knob JOHNSON:
0391036
0391036 KNOB & FRICTION ADJ. SCREW ASSY.
CJ275TLCDC, CJ275TLCOS, CJ300TLCDC, CJ300TLCOS, D100WTLM, HJ55WMLM, HJ55WMLZ, J100STLCCA, J100STLCEM, J100STLESB, J100WMLCDR, J100WMLCOC, J100WMLCRS, J100WTLCUA, J100WTLESM, J100WTLZ, J10EESC, J110MLCCA, J110MLCDC, J110MLCEM, J110MLCUR, J115MLCNB, J1
0331049
0331049 KNOB, Handle
CJ275TLCDC, CJ275TLCOS, CJ300TLCDC, CJ300TLCOS, D100WTLM, J100STLCCA, J100STLCEM, J100STLESB, J100WMLCDR, J100WMLCOC, J100WTLCUA, J100WTLESM, J100WTLZ, J10EESC, J110MLCCA, J110MLCDC, J110MLCEM, J110MLCUR, J115MLCOS, J115MLESB, J120TLAEM, J120TLASB, J
0125200
0125200 KNOB, Switch hsg.
J120TLAEM, J120TLASB, J120TLCCA, J140CXCCS, J140CXCEC, J140CXESR, J150CXCCA, J150CXCEM, J150CXESB, J175STLACM, J175STLCEB, J175STLESE, J185ESXESS, J185ESXW, J200CXCCR, J200CXCEA, J200CXESM, J225CXCCE, J225CXCED, J225CXESS, J275CXCCA, J300CXCCA, J300C