0325267 JOHNSON LEAF VALVE

This engine uses high voltage to control the fuel injectors.Disconnect electronic fuel injector enable circuit connector to prevent personal injury.Do not come in contact with the fuel injector terminals while the engine is running.
Specifications
Table 1
Inlet and Exhaust Valve Lash Specifications
Setting Type Specification
C13 Inlet Valve Lash 0.38 0.08 mm (0.015 0.003 inch)
C13 Exhaust Valve Lash 0.76 0.08 mm (0.030 0.003 inch)
C15/C18 Inlet Valve Lash 0.38 0.08 mm (0.015 0.003 inch)
C15/C18 Exhaust Valve Lash 0.81 0.08 mm (0.032 0.003 inch)
Table 2
Compression Brake Lash Specifications
Setting Type Specification
C13 Compression Brake Valve Lash 0.711 0.05 mm (0.028 0.002 inch)
C15/C18 Compression Brake Valve Lash 0.686 0.05 mm (0.0270 0.002 inch)
Table 3
Variable Valve Actuator Lash Specifications
Setting Type Specification
C15/C18 Variable Valve Actuator Valve Lash 0.50 0.08 mm (0.020 0.003 inch)
Table 4
Fuel Injector Specifications
Setting Type Specification
Fuel Injector Settings Turn to touch and extra 180 degree turn Introduction
Use the procedure below to inspect and adjust the valve mechanism lash settings.Note: Valve lash is measured between the rocker arm and the valve bridge. All measurements and adjustments must be made with the engine stopped and the valves fully closed.References
Reference: Testing and Adjusting, Finding Top Center Position No. 1 PistonReference: Disassembly and AssemblyMechanical Electronic Injector Unit (MEIU) and Valve Lash Adjustment Procedure
Put the number 1 piston at Top Dead Center (TDC) on the compression stroke. Refer to the Testing and Adjusting, Finding Top Center Position No. 1 Piston.Note: To check that the number 1 piston is on TDC, both the inlet and exhaust valves on cylinder number 1 will move freely. If the valves do not move freely, cylinder number 1 is on TDC of the exhaust stroke. Install the timing pin in the flywheel.
Table 5
TDC No. 1 Compression Stroke Inlet Valves Exhaust Valves
Valve Lash C13
0.38 0.08 mm (0.015 0.003 inch)
C15 and C18
0.38 0.08 mm (0.015 0.003 inch) C13
0.76 0.08 mm (0.030 0.003 inch)
C15 and C18
0.81 0.08 mm (0.032 0.003 inch)
Cylinders 1–2–4 1–3–5
Adjust the valve lash using the specifications from Table 5.
Lightly tap the rocker arm with a soft mallet.Note: This ensures that the roller lifter seats against the base circle of the camshaft.
Loosen the adjustment locknut for the appropriate valves.
Place the feeler gauge between the rocker arm and the valve bridge.
Turn the adjustment screw in a clockwise direction while sliding the feeler gauge back and forth between the rocker arm and valve bridge. Continue turning the adjustment screw in a clockwise direction until a slight drag is felt on the feeler gauge.
Tighten the adjustment locknut to 30 7 N m (22 5 lb ft).Note: Do not allow the adjustment screw to turn while torquing the locknut.
Recheck the valve lash after tightening the adjustment locknut. Remove the feeler gauge.
Follow the steps below to set the mechanical unit injectors on TDC of number 1 piston compression stroke.Note: Injectors for cylinders 3, 5, and 6 can be adjusted at TDC of number 1 piston compression stroke.
Loosen the adjustment locknut for the injector.
Turn the adjustment screw clockwise until the screw contacts the mechanical electronic unit injector.
Turn the adjustment screw an extra two turns clockwise to push all the fuel out of the injector plunger.Note: The additional turns will ensure the injector pre-load is set accurately.
Turn the adjustment screw counter-clockwise for 2.5 turns.
Turn the adjustment screw clockwise until the screw contacts the injector.
Turn the screw clockwise an extra 180 degrees or half turn.
Tighten the locknut to 55 10 N m (41 7 lb ft) while not allowing the adjustment screw to turn for C13 engines. Tighten the locknut to 100 10 N m (74 7 lb ft) while not allowing the adjustment screw to turn for C15 and C18 engines
Remove the timing pin and rotate the engine 360 degrees in the direction of engine rotation. This will put the engine at TDC of number 6 piston. Pin the flywheel with the timing pin.Note: To check that the number 1 piston is on TDC, both the inlet and exhaust valves on cylinder number 6 will move freely. If the valves do not move freely, cylinder number 6 is on TDC of the exhaust stroke. Install the timing pin in the flywheel.