0305220 JOHNSON LEVER,Choke


0305220 LEVER,Choke JOHNSON VX-14B LEVER
0305220 LEVER,Choke JOHNSON
Rating:
18

Buy LEVER,Choke 0305220 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 33
 

Compatible models:

VX-14B   JOHNSON

BRP JOHNSON entire parts catalog list:

VX-14B, VXH-14B, VXHL-14B, VXL-14B 1968

Information:

Start By:a. remove fuel injection lines
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
1. Remove bolts (1) and fan guard (2). 2. Loosen bolts (7), (9) and (10). Remove belts (8).3. Remove bolt (4) to clip. Remove grease line (3).4. Remove nuts (6). Remove cover (5) and the gasket. 5. Loosen bolt (12) enough to leave a gap of 3.18 mm (.125 in) between washers (11) and the fuel pump drive gear.6. Install tool (A) as shown. Tighten the stud to pull the fuel pump drive gear loose from the taper on the fuel injection pump camshaft.7. Remove tool (A), bolt (12), and washer (11). 8. Identify and disconnect wires (13).9. Remove tube assemblies (15) and (18).10. Remove two bolts (14), fuel transfer pump (17), and the O-ring seal.11. Remove bolts (16), the filter base, the gasket, and filter (19). 12. Fasten the fuel injection pump housing and governor to a hoist.13. Remove two bolts (22), three nuts (21), and the fuel injection pump housing and governor. The weight of the fuel injection pump housing and governor is 29 kg (64 lb.).14. Remove the two O-ring seals from the bottom of the fuel injection pump housing and governor. 15. Loosen screw (25). Remove two screws (26), control assembly (23) and spacers (24).Install Fuel Injection Pump Housing And Governor
Start By:a. remove fuel injection linesb. remove valve cover Number 1 piston must be set at top dead center (TDC) to perform all timing procedures. The engine is seen from the flywheel end when direction of crankshaft rotation is given. 1. Remove the starter.2. Install tool (B) on flywheel housing as shown.3. To find TDC for No. 1 piston;a. Turn the flywheel clockwise (opposite the direction of engine rotation) approximately 30 degrees. This removes all play from the timing gears. If you go past the bolt hole, you must repeat Step (a).b. Turn the flywheel counterclockwise until a 3/8" - 16 x 2 1/4" NC bolt (27) can be installed in the flywheel through the hole in the flywheel housing. The No. 1 and No. 6 pistons are now at top center position. The No. 1 piston is on the compression stroke when the valves of the No. 1 cylinder are closed. The rocker must be free to move up and down.4. If No. 1 piston is not on the compression stroke, remove the 3/8" - 16 x 2 1/4" NC bolt (27) and turn the flywheel 360° counterclockwise. Install the 3/8" bolt as before. The No. 1 piston is now at TDC.
Typical Example5. Install tooling (C) in the fuel injection pump housing as shown. Push on tooling (C) and turn injection pump camshaft (32). When tooling (C) engages the groove (slot) in the camshaft, the fuel injection pump is in the No. 1 piston TDC position.6. Be sure O-ring seals (28), (29), (30) and (31) are in position on the fuel injection pump housing and governor. Put clean engine oil on the seals.7. Place control assembly (23) and spacers (24) in position on the fuel injection pump housing and governor. Install screws (26) and tighten screw (25). 8. Attach a hoist and put the fuel injection pump housing and governor in position on the timing gear plate and oil manifold. Install three nuts (21) and two bolts (22). 9. Put the drive gear in position on the fuel injection pump and install washers (11) and bolt (12) finger tight. Be sure that tool (C) is in the notch in the camshaft of the fuel injection pump.10. Install a 3/8" - 24 × 1/2" NC bolt in one of the holes in the drive gear. 11. Use a torque wrench to place a force of 68 N m (50 lb ft) on the 3/8" bolt while tightening the drive gear bolt to a torque of 270 25 N m (200 18 lb ft). Remove tool (C) from the fuel pump and the 3/8" - 16 × 2 1/4" bolt (27) from the flywheel.12. With tooling (B), turn the engine flywheel two complete revolutions. When the 3/8" - 16 × 2 1/4" bolt goes in the hole in the flywheel when the timing pin is installed in the notch in the camshaft, the timing is correct.13. Remove tool (B). 14. Put cover (31) and the gasket in position. Install four bolts (32).15. Put the filter base, the gasket, and filter (19) in position. Install bolts (16).16. Put fuel transfer pump (17) and the O-ring seal in position. Install two bolts (14).17. Install tube assemblies (18) and (15). Connect wires (13).18. Put the gasket and cover (5) in position. Install the washers and nuts (6). Install grease line (3) and bolt (4) to the clip.19. Install belts (8). Use belt tension gauge and adjust the fan belts. Measure the bell farthest from the engine. Tighten new belts until gauge indication is 534 22 N (120 5 lb.). Tighten bolt (7), bolt (9), and bolt (10). Operate the engine at high idle for a minimum of 30 minutes after Step 18. Make another adjustment of the belt tension. The correct gauge indication for a used belt is 400 44 N (90 10 lb.). Tighten bolt (7), bolt (9), and (10).20. Put fan guard (2) in position and install bolts (1).End By:a. install valve coverb. install fuel injection lines
Perform Scheduled Oil Sampling after performing service work to check for fuel leakage and contaminants left in the system following repair. Contaminants put into the system may cause rapid wear and shortened component life.


Parts lever JOHNSON:

0313671
 
0313671 LEVER,Reverse locking
V4A-20A, V4S-20A, V4T-14B, VX-14B
0312463
 
0312463 LEVER,Manual,rev.lock
V4A-20A, V4S-20A, V4T-14B, VX-14B
0305342
 
0305342 LEVER,Shift rod
V4S-20A, VX-14B
0305719
0377728
0307440
 
0307440 LEVER,Throttle control
V4A-20A, V4S-20A, VX-14B
0313894
 
0313894 LEVER,Shift lock
V4S-20A, VX-14B
0314183
Back to top