0326644 JOHNSON LEVER,Shift rod

Table 1
Diagnostic Codes Table
Description Conditions which Generate this Code System Response
446-5 Air Shutdown Relay current below normal The Electronic Control Module (ECM) detects an open circuit and/or a short to the +Battery in the solenoid circuit. The configurable parameter for the air shutoff is set to "Enabled". The code is logged.
446-6 Air Shutoff Relay short The ECM detects a short circuit to ground in the solenoid circuit. The configurable parameter for the air shutoff is set to "Enabled".
E2087(3) Air Intake Shutoff Closed The ECM detects an "Active" condition in the detection circuit that monitors the state of the air shutoff valves. The configurable parameter for the detection circuit is set to "Installed". The code is latched until power is cycled to the ECM. The process for starting the engine will be stopped and the process for starting the engine will be disabled. If engine rpm is present, the air shutoff relay will be activated.
The code is logged.
E2088(1) Air Intake Shutoff Detection Circuit Detected but Not Installed The ECM detects an "Active" condition in the detection circuit that monitors the state of the air shutoff valves. The configurable parameter for the detection circuit is set to "Not Installed". The code is logged. The engine's ECM has the ability to stop the engine by cutting off the inlet air supply in an emergency situation. The ECM activates the air shutoff solenoid in order to close the air shutoff valve. The air shutoff is optional. A programmable parameter needs to be set to "Installed" with Caterpillar Electronic Technician (ET) in order to enable the air shutoff system.There is a switch at each of the air shutoff valves that is included in a detection circuit that inputs a signal to the engine ECM. The ECM monitors the input from the detection circuit in order to determine if the air shutoff valves are in the closed position. If the circuit indicates that the air shutoff valves are closed, the ECM will generate the E2087 event code.There are three conditions which cause the engine control to activate the air shutoff solenoid. The first condition occurs when the operator initiates an emergency shutdown. When the emergency shutdown is recognized, fuel is shut off and the air shutoff solenoid is activated. The second condition is for an engine overspeed. The third condition occurs when engine rpm is present and the detection circuit indicates an "ACTIVE" input to the ECM.The input for the air shutoff switch is "NOT ACTIVE" when the switch circuit indicates an open circuit between terminal P1-55 and terminal P1-56. The input for the air shutoff switch is "ACTIVE" when the switch circuit indicates a closed circuit between terminal P1-55 and terminal P1-56.Ensure that BOTH of the air shutoff valves are manually reset after activating the air shutoff system in order to start the engine again. Regardless of the reason for activation, the main power to the ECM must be turned OFF for 30 seconds in order to reset the engine control.
Illustration 1 g01256335
Typical schematic
Illustration 2 g01256336
P1 ECM connector
(P1-5) Digital return
(P1-23) Emergency stop signal 2
(P1-28) Emergency stop signal 1
(P1-52) +Battery
(P1-55) Battery
(P1-56) Air shutoff switch
(P1-63) −Battery
Illustration 3 g01256338
P2 ECM connector
(P2-13) Air shutoff
Illustration 4 g01234146
Location of ECM connectors
Illustration 5 g01256339
Connector "A"
(Terminal 7) +Battery
(Terminal 11) −Battery
(Terminal 21) Emergency stop signal 2
(Terminal 23) Emergency stop signal 1
(Terminal 25) Digital return
Illustration 6 g01256343
Connector "G"
(Terminal 3) Emergency stop signal 1
(Terminal 7) Emergency stop signal 2
(Terminal 37) Digital return Test Step 1. INSPECT ELECTRICAL CONNECTORS AND WIRING
Remove electrical power from the ECM.
Thoroughly inspect the J1/P1 ECM connector and the J2/P2 ECM connector. Inspect all of the connectors that are associated with the circuit. Refer to Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connectors that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque. Refer to Troubleshooting, "Inspecting Electrical Connectors" for details.
Check the harness and wiring for abrasion and for pinch points. Expected Result:All connectors, pins and sockets are completely coupled and/or inserted and the harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The connectors and wiring are free of any problems. Proceed to Test Step 2.
Not OK - The wiring and/or connectors are in need of repair.Repair: Repair the wiring and/or connectors or replace the wiring and/or connectors. Refer to Troubleshooting, "Inspecting Electrical Connectors".STOPTest Step 2. CHECK FOR "ACTIVE" DIAGNOSTIC CODES OR FOR "ACTIVE" EVENT CODES
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
Restore electrical power to the ECM.
Monitor the diagnostic codes on Cat ET. Check and record any diagnostic codes. Note: Wait at least 30 seconds in order for the diagnostic codes to become active.
Determine if a diagnostic code has occurred several times. Note: A diagnostic code that is logged several times is an indication of an intermittent problem. Most intermittent problems are the result of a bad connection between a socket and a pin in a connector or a bad connection between a wire and a terminal. The problem may be caused by moisture, corrosion, or wear.
Determine if the problem is active and related to one of the following diagnostic codes:
446-5
446-6
E2087
E2088Expected Result:A diagnostic code or an event code is not active.Results:
OK -