0315193 JOHNSON LOCATING BRACKET, Front


0315193 LOCATING BRACKET, Front JOHNSON 100ESL71A, 100ESL72R, 115ESL69E, 115ESL70D, 115ESL73M, 125ESL71C, 125ESL72R, 135ESL73M, 85ESL69E, 85ESL70B, 85ESL71A, 85ESL72R, 85ESL73M LOCATING
0315193 LOCATING BRACKET, Front JOHNSON
Rating:
18

Buy LOCATING BRACKET, Front 0315193 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

BRP JOHNSON entire parts catalog list:

100ESL71A, 100ESL71C 1971
100ESL72R 1972
115ESL69E, 115ESL69S 1969
115ESL70D 1970
115ESL73M 1973
125ESL71C 1971
125ESL72R 1972
135ESL73M 1973
85ESL69E, 85ESL69M, 85ESL69S 1969
85ESL70B, 85ESL70D 1970
85ESL71A, 85ESL71H 1971
85ESL72R 1972
85ESL73M 1973

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) - 1/2 Inch Drive T50 Torx Bit 1
- 10 mm Triple Square Spline 1
B - Guide Studs
M10 by 80 mm 2
C - Guide Studs
M10 by 130 mm 2
(1) Either tool may be necessary in order to install the alternator pulley.
If necessary, follow Step 1.a through Step 1.k in order to install the alternator bracket to the cylinder block of the hydraulic excavator.
Ensure that all of the components of the alternator bracket are clean and free from wear and damage. Replace all components that are worn or damaged.
Illustration 1 g02095234
Position bracket (22) onto the cylinder block. Ensure that the bracket is correctly oriented.
Install bolts (23) and tighten the bolts to a torque of 44 N m (32 lb ft).
Illustration 2 g02165614
Illustration 3 g02352949
Install Tooling (B) to the cylinder block.
Position alternator bracket (17) onto Tooling (B). Install bolts (18) to the alternator bracket and hand tighten the bolts. Note: Support the alternator bracket as the bolts are installed. The weight of the bracket is approximately 19 kg (42 lb).
Remove Tooling (B) and install the remaining bolts (18) to the alternator bracket and hand tighten the bolts.
Ensure that spacers (20) are correctly installed to alternator bracket (17).
Install bolts (19) to alternator bracket (17) and hand tighten the bolts.
Illustration 4 g02165494
Tighten bolts (18) to a torque of 44 N m (32 lb ft).
Tighten bolts (19) to a torque of 44 N m (32 lb ft). Note: Ensure that Position (X) on alternator bracket (17) does not move in either direction.
Install the refrigerant compressor. Refer to Disassembly and Assembly, "Refrigerant Compressor - Remove and Install" for the correct procedure. Installation Procedure
Illustration 5 g02022404
Illustration 6 g02165615
Illustration 7 g02352950
If necessary, follow Step 1.a through Step 1.h in order to install alternator bracket (11) onto the cylinder block.
Ensure that alternator bracket (11) is clean and free from wear and damage. If necessary, replace the alternator bracket.
Ensure that dowels (16) are free from wear and damage. If necessary, replace the dowels.
Install Tooling (B) to the cylinder block.
Position alternator bracket (11) onto Tooling (B). Install bolts (12) hand tight.
Remove Tooling (B) and install remaining bolts (12) hand tight.
Tighten bolts (12) to a torque of 44 N m (32 lb ft).
If necessary, install belt tensioner (14) onto alternator bracket (11) and tighten bolt (15). Refer to Disassembly and Assembly, "Belt Tensioner - Install" for the correct procedure.
If necessary, install flat idler pulley (13) onto alternator bracket (11). Refer to Disassembly and Assembly, "Idler Pulley (Flat Idler Pulley) - Remove and Install" for the correct procedure.
Illustration 8 g02019754
Typical example
If necessary, follow Step 2.a through Step 2.d in order to install pulley (8) to alternator (2). Note: Either of Tooling (A) may be required in order to carry out the installation of the alternator pulley.
Place alternator (2) in a suitable support.
Ensure that pulley (8) is correctly oriented.
Install pulley (8) and a new nut (9) to alternator shaft (10).
Position a cranked ring spanner onto nut (9) and use a suitable tool in order to prevent the cranked ring spanner from turning. Use Tooling (A) in order to turn the shaft of the alternator in a counterclockwise direction. Tighten the nut to the correct torque. Refer to Specifications, "Alternator" for the correct torque.


Parts locating JOHNSON:

0315190
 
0315190 LOCATING BRACKET, Rear
100ESL71A, 100ESL72R, 115ESL69E, 115ESL70D, 115ESL73M, 125ESL71C, 125ESL72R, 135ESL73M, 85ESL69E, 85ESL70B, 85ESL71A, 85ESL72R, 85ESL73M
Back to top