0321641 JOHNSON LOCKNUT, Input stud


0321641 LOCKNUT, Input stud JOHNSON 25E77S, 25E78C, 25E79R, 35E76G, 35E77C, 35E78R, 35E79A, J20CRCCA, J20CRCDC, J20CRCOS, J20CRCUR, J20ECEM, J20EEIE, J20EEND, J20EESB, J20EETS, J25ECCM, J25ECDR, J25ECEB, J25ECIB, J25ECNE, J25ECOC, J25ECRS, J25ECTD, J25ECUA, J25EEID, J25EENS, J25EESE, J LOCKNUT
0321641 LOCKNUT, Input stud JOHNSON
Rating:
88

Buy LOCKNUT, Input stud 0321641 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 19
 

BRP JOHNSON entire parts catalog list:

25E77S, 25EL77H, 25EL77S, 25R77H, 25R77S, 25RL77H, 25RL77S 1977
25E78C, 25EL78C, 25R78C, 25RL78C 1978
25E79R, 25EL79R, 25R79R, 25RL79R 1979
35E76G, 35E76S, 35EL76G, 35EL76S, 35R76G, 35R76S, 35RL76G, 35RL76S 1976
35E77C, 35E77H, 35EL77C, 35EL77H, 35R77C, 35R77H, 35RL77C, 35RL77H 1977
35E78R, 35EL78R, 35R78R, 35RL78R 1978
35E79A, 35EL79A, 35R79A, 35RL79A 1979
J20CRCCA, J20CRLCCA, J20ECCA, J20ELCCA 1988
J20CRCDC, J20CRLCDC, J20ECDC, J20ELCDC, J20TECDC 1986
J20CRCOS, J20CRLCOS, J20ECOS, J20ELCOS 1985
J20CRCUR, J20CRLCUR, J20ECUR, J20ELCUR 1987
J20ECEM, J20ELCEM 1989
J20EEIE, J20ELEIE 1991
J20EEND, J20ELEND 1992
J20EESB, J20ELESB 1990
J20EETS, J20ELETS 1993
J25ECCM, J25ELCCM, J25RCCA, J25RLCCA, J25TECCA, J25TELCCA 1988
J25ECDR, J25ELCDR, J25RCDC, J25RDC, J25RLCDC, J25TECDC, J25TELCDC 1986
J25ECEB, J25ELCEB, TJ25ELCEB, TJ25ELESF 1989
J25ECIB, J25ECIM, J25ELCIB, J25ELCIM, J25RCIM, J25RLCIM, J25TECIM, J25TELCIM 1981
J25ECNE, J25ELCNE, J25RCNB, J25RELCNB, J25RLCNB, J25TECNB 1982
J25ECOC, J25ELCOC, J25RCOS, J25RLCOS, J25TECOS, J25TELCOS 1985
J25ECRS, J25ELCRS, J25RCRD, J25RLCRD, J25TECRD, J25TELCRD 1984
J25ECTD, J25ELCTD, J25RCTE, J25RLCTE, J25TECTE, J25TELCTE 1983
J25ECUA, J25ELCUA, J25RCUR, J25RLCUR, J25TECUR, J25TELCUR 1987
J25EEID, J25ELEID, TJ25ELEID, VJ25ELEID 1991
J25EENS, J25ELENS, TJ25ELENS, VJ25ELENS 1992
J25EESE, J25ELESE, TJ25ELESE, VJ25ELESE 1990
J25EETC, J25ELETC, TJ25ELETC, VJ25ELETC 1993
J25RCSA, J25RLCSA, J25TECSA, J25TELCSA 1980
J25TECEM, J25TELCEM 1989
J25TEEIE, J25TELEIE 1991
J25TEEND, J25TELEND 1992
J25TEESB, J25TELESB 1990
J25TEETS, J25TELETS 1993
J28ELCDS 1986
J28ELCDS 1986
J28ESLCCR, VJ28ESLCCR 1988
J28ESLCCR, VJ28ESLCCR 1988
J28ESLCEA, VJ28ESLCEA 1989
J28ESLCEA, VJ28ESLCEA 1989
J28ESLCUC 1987
J28ESLCUC 1987
J28ESLEIB 1991
J28ESLEIB 1991
J28ESLENE 1992
J28ESLENE 1992
J28ESLESM, VJ28ESLESM 1990
J28ESLESM, VJ28ESLESM 1990
J28ESLETD 1993
J28ESLETD 1993
J30ECCE, J30ELCCE, J30RCCE, J30RLCCE, J30TECCE, J30TELCCE 1988
J30ECDM, J30ELCDM, J30RCDM, J30RLCDM, J30TECDM, J30TELCDM 1986
J30ECED, J30ELCED, TJ30ELCED, TJ30ELESF 1989
J30ECOA, J30ELCOA, J30RCOA, J30RLCOA, J30TECOA, J30TELCOA 1985
J30ECRR, J30ELCRR 1984
J30ECUB, J30ELCUB, J30RCUB, J30RLCUB, J30TECUB, J30TELCUB 1987
J30EEIC, J30ELEIC, VJ30EEIC, VJ30ELEIC 1991
J30EENR, J30ELENR, VJ30EENR, VJ30ELENR 1992
J30EESS, J30ELESS 1990
J30EETA, J30ELETA, VJ30EETA, VJ30ELETA 1993
J30TECED, J30TELCED 1989
J30TEEIC, J30TELEIC 1991
J30TEENR, J30TELENR 1992
J30TEESS, J30TELESS 1990
J30TEETA, J30TELETA 1993
J35ECIG, J35ELCIG, J35RCIG, J35RLCIG 1981
J35ECND, J35ELCND, J35RCND, J35RLCND, J35TELCNB 1982
J35ECRR, J35ELCRR, J35RCRR, J35RLCRR, J35TELCRR 1984
J35ECSM, J35ELCSM, J35RCSM, J35RLCSM 1980
J35ECTS, J35ELCTS, J35RCTS, J35RLCTS, J35TELCTS 1983
J35RCCE, J35RLCCE 1988
J35RCDM, J35RLCDM 1986
J35RCUB, J35RLCUB 1987
TJ30ELESS, VJ30EESS, VJ30ELESS 1990

Information:

Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 1
Troubleshooting Test Steps Values Results
1. Diagnostic Codes
A. Establish communication between the electronic service tool and the Electronic Control Module (ECM) . If necessary, refer to Troubleshooting, "Electronic Service Tools".
B. Check if any codes are active or logged.
Diagnostic code
Result: A code is active or logged.
Repair: Troubleshoot any codes before continuing with this procedure.
Result: A code is not active or logged.
Proceed to Test Step 2.
2. Accessory Equipment
A. Check all accessory equipment for faults that may create excessive load on the engine.
Accessories
Result: An engine accessory is creating an excessive load.
Repair: Repair or replace the engine accessory.
Result: An engine accessory is not creating an excessive load.
Proceed to Test Step 3.
3. Power Mode Control (If Equipped)
A. Check whether the power mode control is using the Cat data link or the CAN data link and then use the appropriate test. Refer to Troubleshooting, "Data Link - Test" or Troubleshooting, "CAN Data Link - Test".
B. Check the engine wiring harness for defects. Refer to Troubleshooting, "Electrical Connectors - Inspect".
Power mode control
Result: There is a fault in the data link.
Repair: Repair the data link, as necessary.
Result: There is a wiring fault.
Repair: Repair or replace the wiring, as necessary.
Result: The data link and the wiring are OK.
Proceed to Test Step 4.
4. Fuel Supply
A. Ensure that the vent in the fuel cap is not filled with debris.
B. Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
C. If the temperature is below 0 °C (32 °F), check for solidified fuel (wax).
D. Check the primary filter/water separator for water in the fuel.
E. Check for fuel supply lines that are restricted.
F. Replace the in-line fuel filter that is installed upstream of the Electric Fuel Lift Pump (EFLP).
G. Check that the EFLP is operating correctly.
H. Replace the primary and secondary fuel filters.
I. Check the diesel fuel for contamination. Refer to Systems Operation, Testing, and Adjusting, "Fuel Quality - Test".
J. Check for air in the fuel system. Refer to Systems Operation, Testing, and Adjusting, "Air in Fuel - Test".
Fuel system
Result: The vent in the fuel cap is blocked.
Repair: Install a replacement fuel cap.
Result: The fuel contains solidified wax.
Repair: Replace the fuel with fuel of the correct specification for the ambient conditions.
Result: There are fuel supply lines that are restricted.
Repair: Replace any damaged or restricted fuel lines.
The EFLP is suspect. Refer to Troubleshooting, "Fuel Transfer Pump - Test".
Replace the primary fuel filter and the secondary fuel filters. Refer to the Operation and Maintenance Manual for further information.
Result: There is air in the fuel system.
Repair: Prime the fuel system. Refer to Systems Operation, Testing, and Adjusting, "Fuel System - Prime".
Result: The diesel fuel is contaminated.
Repair: Drain the fuel tank and the fuel system.
Replace the primary fuel filter and the secondary fuel filters. Refer to the Operation and Maintenance Manual for further information.
Fill and prime the fuel system with fuel of the correct specification. Refer to Systems Operation, Testing, and Adjusting, "Fuel System - Prime".
Result: The fuel supply is OK.
Proceed to Test Step 5.
5. Low Compression (Cylinder Pressure)
A. Perform a compression test. Refer to Systems Operation, Testing, and Adjusting, "Compression - Test ".
Cylinder compression
Result: The results of the compression test are outside the specifications.
Investigate the cause and rectify any faults.
Note: Possible causes of low compression are shown in the following list:
Loose glow plugs
Faulty piston
Faulty piston rings
Worn cylinder bores
Worn valves
Faulty cylinder head gasket
Damaged cylinder head
Result: The results of the compression test are OK.
Proceed to Test Step 6.
6. Electronic Unit Injectors
A. Use the electronic service tool to perform the automatic "Cylinder Cut Out Test".
Note: If the compression test that was performed in Test Step 5 was satisfactory, the "Cylinder Cut Out Test" will identify any faulty injectors.
Electronic Unit Injectors
Result: A faulty injector is indicated.
Repair: Remove any faulty electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Install new electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Repeat the automatic "Cylinder Cut Out Test". If the fault is still apparent, remove the replacement electronic unit injector and install the original electronic unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" and Disassembly and Assembly, "Electronic Unit Injector - Install".
Result: All injectors are OK.
Contact the Dealer Solutions Network (DSN).


Parts locknut JOHNSON:

0315077
 
0315077 LOCKNUT
100ESL71A, 100ESL72R, 100ML79S, 115EL77S, 115ESL69E, 115ESL70D, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL76S
0325451
 
0325451 LOCKNUT, Steering handle screw
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, BJ15RELEUC, BJ8FRBECA, BJ8FRBEDC, BJ8FRBEUR, D25RWA, HJ10FELECA, HJ15KCF, HJ15
0124640
 
0124640 LOCKNUT
J28ESLCCR, J28ESLCCR, J48ESLCUS, J48ESLCUS, J88MSLCUS, J88MSLCUS
Back to top