0332208 LOOP JOHNSON
J35AELCDE, J35AELCUD, J40AELCCS, J40ECDE, J40ECUD, J45RCE, J50BECCS, J50BECDE, J50BECUD, J55RWLE
LOOP
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$143.99
28-08-2024
6.9[3.11] pounds
Amazon.com
O'Neal mens Element Boot, White, 8
O'Neal Metal shank insert reinforces the shape of the boot and adds support || Easy to operate, Snap-Lock adjustable four buckle closure system || Metal toe guard to protect the sole against delaminating || Synthetic leather heat shield to prevent heat damage || Air mesh interior, generous heel support and cushioned insole for extra comfort
O'Neal Metal shank insert reinforces the shape of the boot and adds support || Easy to operate, Snap-Lock adjustable four buckle closure system || Metal toe guard to protect the sole against delaminating || Synthetic leather heat shield to prevent heat damage || Air mesh interior, generous heel support and cushioned insole for extra comfort
Compatible models:
BRP JOHNSON entire parts catalog list:
- POWER TRIM AND TILT » 0332208
- POWER TRIM AND TILT
J40AELCCS, J40ARLCCS, J40ATLCCS, J40ECCS, J40ELCCS, J40RCCS, J40RLCCS, J40TECCS, J40TELCCS, J40TLCCS, J40TTLCCS 1988
J40ECDE, J40ELCDE, J40RCDE, J40RLCDE, J40TECDE, J40TELCDE, J40TLCDE 1986
J40ECUD, J40ELCUD, J40RCUD, J40RLCUD, J40TECUD, J40TLCUD 1987
J45RCE, J45RCLE, J45WMLE 1989
J50BECCS, J50BELCCS, J50TELCCS, J50TLCCS 1988
J50BECDE, J50BELCDE, J50TELCDE, J50TLCDE 1986
J50BECUD, J50BELCUD, J50TELCUD, J50TLCUD 1987
J55RWLE 1989
Information:
Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Code Description Comments
168-2 168-2 Battery Potential / Power Input #1 : Erratic, Intermittent, or Incorrect This code indicates that the battery circuit to the ECM is intermittent.
168-3 168-3 Battery Potential / Power Input #1 : Voltage Above Normal The ECM detects voltage that is above the acceptable value.
168-4 168-4 Battery Potential / Power Input 1 : Voltage Below Normal The ECM detects voltage that is below the acceptable value.
Follow the troubleshooting procedure to identify the root cause of the fault.
Illustration 1 g03366300
Typical example of the schematic for the electrical power supply circuit
Illustration 2 g03366309
View of the pin locations on the P1 connector for the ignition keyswitch and battery supply circuit
(1) Battery ground
(2) Battery ground
(3) Battery ground
(7) Battery+
(8) Battery+
(9) Battery ground
(10) Battery ground
(15) Battery+
(16) Battery+
(40) Ignition keyswitch
Table 2
Troubleshooting Test Steps Value Results
1. Determine the Diagnostic Code
A. Establish communication between the electronic service tool and the ECM . Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Start the engine. Run the engine until the engine is at normal operating temperature.
C. Observe the "Active Diagnostic" screen on the electronic service tool. Wait at least 30 seconds so that any codes may become active.
Diagnostic code
Result: One of the diagnostic codes listed in Table 1 is active.
Proceed to Test Step 2.
Result: The electronic service tool will not communicate with the ECM.
Repair: Refer to Troubleshooting, "Electronic Service Tool Does Not Communicate".
2. Check the Charging Circuit
A. Check the charging circuit. Refer to Systems Operation, Testing and Adjusting, "Charging System - Test".
Charging circuit
Result: The charging system is OK.
Proceed to Test Step 3.
Result: The charging system is not OK.
Repair: There is a fault in the charging system. Make the necessary repairs.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
3. Load Test the Batteries
A. Use a suitable battery load tester to test the batteries. Refer to Systems Operation, Testing and Adjusting, "Battery - Test" for the correct procedure.
Load test
Result: The batteries pass the load test.
Proceed to Test Step 4.
Result: The batteries do not pass the load test.
Repair: Recharge or replace the faulty batteries.
Use the electronic service tool to clear all logged diagnostic codes and verify that the repair eliminates the fault.
4. Inspect Electrical Connectors and Wiring
A. Ensure that the battery disconnect switch is in the CLOSED position.
B. Thoroughly inspect all connectors associated with the electrical power supplies.
C. Check all fuses.
D. Perform a 45 N (10 lb) pull test on each of the wires in the connectors associated with the electrical power supplies.
E. Check all the wiring associated with the electrical power supplies for abrasions and pinch points.
F. Verify that the "System Operating Voltage Configuration" is correctly configured in the Engine ECM configuration parameters.
Damaged wire or connector. Blown fuse.
Result: A damaged wire or damaged connector was found. A blown fuse was found.
Repair: Repair the damaged wire or the damaged connector. Replace all blown fuses.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
Result: The "System Operating Voltage Configuration" is configured incorrectly.
Repair: Program the parameter with the correct system voltage.
Result: A damaged wire or damaged connector was not found. The fuses are OK.
Contact the Dealer Solutions Network (DSN).
Parts loop JOHNSON:
0122498
0122498 LOOP
115EL77S, 115ESL74B, 115ESL75E, 135ESL74B, 135ESL75E, 85EL76D, 85EL77S, J35AELCDE, J35AELCUD, J40AELCCS, J40ECDE, J40ECUD, J45RCE, J50BECCS, J50BECDE, J50BECIC, J50BECNR, J50BECOB, J50BECRM, J50BECTA, J50BECUD, J55RCIM, J55RWLE, J60ECIA, J60ECNM, J60