5032440 MODULE, ENGINE CONTROL 50HP JOHNSON
J40PL4SNF, J50PL4SNF
MODULE
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
$41.60
14-08-2020
4.40924524[1.80] Pounds
-: -
Connected Essentials 5032440 Grey with Blue Trim Tailored Heavy Duty Custom Fit Car Mats Vauxhall Zafira B (6 Piece Set) (2006-2011)
Complete set of 6 tailored custom fit car mats - designed and manufactured specifically for Vauxhall Zafira B (6 Piece Set) (2006-2011) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Complete set of 6 tailored custom fit car mats - designed and manufactured specifically for Vauxhall Zafira B (6 Piece Set) (2006-2011) || Supplied with clips (as applicable) for security || Driver's mat with heel pad of the same thickness as the mat itself - to reduce wear and protect footwear || Manufactured from 650gram automotive quality carpet - for strength and durability || Images shown are for example only. Mats supplied will be the specific fit for your make & model - see actual template (in images) for this vehicle model.
Number on catalog scheme: 12
BRP JOHNSON entire parts catalog list:
Information:
Table 1
J1939 Code and Description CDL Code and Description System Response
4214-5
Engine Fan Reverse Actuator : Current Below Normal 485-5
Engine Fan Reversing Solenoid : Current Below Normal This code indicates that there is an open circuit in the engine reversing fan solenoid circuit.
4214-6
Engine Fan Reverse Actuator : Current Above Normal 485-6
Engine Fan Reversing Solenoid : Current Above Normal This code indicates that there is a short circuit in the engine reversing fan solenoid circuit.
Table 2
Troubleshooting Test Steps Values Results
1. Determine the Code
A. Establish communication between Cat® Electronic Technician (ET) and the engine ECM. Refer to Troubleshooting, "Electronic Service Tools", if necessary.
B. Download the "Warranty Report" from the engine ECM before performing any troubleshooting or clearing diagnostic trouble codes.
C. Look for an active or logged -5 code or -6 code.
Codes
Result: An active or logged -5 code is present.
Proceed to Test Step 2.
Result: An active or logged -6 code is present.
Proceed to Test Step 3.
2. Check for an Open Circuit
A. Turn the keyswitch to OFF.
B. Disconnect the engine reversing fan solenoid connector from the wiring harness.
C. Verify that the harness connector is free of debris, free of corrosion, and was securely connected.
D. Connect a jumper wire between the terminals of the harness connector for the engine reversing fan solenoid. The solenoid coil is replaced with a short circuit.
E. Turn the keyswitch to ON.
F. Use the "Engine Reversing Fan Solenoid Override" in Cat ET to turn the solenoid to ON.
G. Check for active codes.
Short Circuit
Result: A -5 code became active. An open circuit has been detected in the wiring harness.
Repair: Repair the wiring or replace the wiring.
Proceed to Test Step 4.
Result: A -6 code became active. The short circuit was detected by the ECM.
Repair: Replace the engine reversing fan solenoid.
Proceed to Test Step 4.
3. Check for a Short Circuit
A. Turn the keyswitch to OFF.
B. Disconnect the engine reversing fan solenoid connector from the wiring harness.
C. Verify that the harness connector is free of debris, free of corrosion, and was securely connected.
D. Turn the keyswitch to ON.
E. Check for active codes.
Open Circuit
Result: A -5 code became active. The open circuit was detected by the ECM.
Repair: Replace the engine reversing fan solenoid.
Proceed to Test Step 4.
Result: A -6 code became active. A short circuit has been detected.
Repair: Repair the wiring or replace the wiring.
Proceed to Test Step 4.
4. Check the Engine Reversing Fan Operation
A. Start the engine.
B. Activate the engine reversing fan using the engine reversing fan switch.
Engine Reversing Switch
Result: The engine reversing fan is not operating properly.
Proceed to Test Step 5.
Result: The engine reversing fan is operating properly.
Return the unit to service.
5. Check the Engine Reversing Fan Switch
A. Disconnect the engine reversing fan solenoid connector from the wiring harness.
B. Use a jumper wire to short circuit the signal and ground wires together on the harness side of the connector for the switch.
C. Turn the keyswitch to ON.
D. Connect to Cat ET. Monitor the engine reversing fan switch parameters in the status screen.
E. Wait at least 30 seconds and check the status of the engine fan reverse switch on Cat ET. The correct status for the switch is ON while the jumper wire is in place.
F. Remove the jumper wire from the connector. Wait at least 30 seconds and check the status of the engine fan reverse switch on Cat ET. The correct status for the switch is OFF with the jumper wire removed.
Status Change
Result: The switch status changed in Cat ET. A failed engine reversing fan switch has been detected.
Repair: Replace the engine reversing fan switch. Verify that the problem has been resolved. Return the unit to service.
Result: The switch did not change status in Cat ET. A wiring problem between the switch and the ECM has been detected.
Repair: Repair or replace the wiring harness between the switch and the engine harness. Verify that the problem has been resolved. Return the unit to service.
If the procedure did not correct the issue, contact your Cat dealer Technical Communicator (TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).
Parts module JOHNSON:
5032439