0390313 JOHNSON MOTOR COVER ASSY.


0390313 MOTOR COVER ASSY. JOHNSON J55RLCSA, J60ECSR MOTOR
0390313 MOTOR COVER ASSY. JOHNSON
Rating:
93

Buy MOTOR COVER ASSY. 0390313 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

J55RLCSA   J60ECSR   JOHNSON

BRP JOHNSON entire parts catalog list:

J55RLCSA 1980
J60ECSR, J60ELCSR 1980

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     150-3992     Timing Pin (1)     1    
150-3993 Timing Pin (2)     1    
B     173-9774     Bolt Remover     1    
( 1 ) The timing pin is required in order to install Bosch fuel injection pumps.
( 2 ) The timing pin is required in order to install Lucas and Stanadyne fuel injection pumps.Start By:
Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove".
Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install".Note: Access to the fuel injection pump gear can also be gained by the removal of an access cover on the front housing. The cover may have bolts that are tamperproof. The bolts can be removed with Tool (B).
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Ensure that the number 1 cylinder is at the top center position on the compression stroke. Refer to the Testing and Adjusting, "Fuel System" topic for additional information.
Illustration 1 g00567390
Typical example
Illustration 2 g00567399
Typical exampleNote: Do not remove hub nut (4) from the shaft of the fuel injection pump. The hub of the fuel injection pump is installed in the correct position from the factory in order to ensure proper timing. If hub nut (4) is removed and the hub is removed, the hub will need to be accurately installed on the shaft of the fuel injection pump. Special equipment is available at your Caterpillar Dealer for this procedure.Note: Do not release torx screws (5). If the torx screws are released and the timing plate is moved, the timing position that is set at the factory will be lost. If the torx screws are released, the number 1 cylinder must be set to the top center position on the compression stroke before the torx screws are tightened.
Slowly rotate the crankshaft until hole (6) in the timing gear and hole (7) in the hub are in alignment with hole (8) in the fuel injection pump body .Note: The location of Tool (A) for Bosch fuel injection pumps will be located toward the top of the fuel injection pump. The location of Tool (A) for Lucas and Stanadyne fuel injection pumps will be located toward the bottom of the fuel injection pump.
Install Tool (A) through hole (6) in the timing gear and hole (7) in the hub. Push Tool (A) into position in hole (8) in the fuel injection pump body. If Tool (A) can be fully seated, the fuel injection pump timing is correct. No resistance should be felt when the timing pin is inserted into hole (8) of the fuel injection pump body.
Remove four bolts (1). Timing gear (2) should be free from the fuel injection pump shaft.
Illustration 3 g00567603
Typical example
Remove three nuts (9) and fuel injection pump (10) from the engine.
Illustration 4 g00567617
Typical example
Remove O-ring seal (11) from fuel injection pump (10) .


Parts motor JOHNSON:

0582061
 
0582061 MOTOR CABLE ASSY
50R79C, 55E79C, J40ECRM, J50BECIC, J50BECNR, J50BECRM, J50BECTA, J50ECSR, J55RCIM, J55RLCSA, J60ECIA, J60ECNM, J60ECSR, J60ECTB, J60ELCRE
0324963
 
0324963 MOTOR COVER,Lower
50R79C, 55E79C, J50ECSR, J55RLCSA, J60ECSR
0390314
 
0390314 MOTOR COVER ASSY.
J55RLCSA, J60ECSR
0391599
 
0391599 MOTOR COVER,Lower
J55RLCSA, J60ECSR
Back to top