0390314 JOHNSON MOTOR COVER ASSY.


0390314 MOTOR COVER ASSY. JOHNSON J55RLCSA, J60ECSR MOTOR
0390314 MOTOR COVER ASSY. JOHNSON
Rating:
98

Buy MOTOR COVER ASSY. 0390314 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 1
 

Compatible models:

J55RLCSA   J60ECSR   JOHNSON

BRP JOHNSON entire parts catalog list:

J55RLCSA 1980
J60ECSR, J60ELCSR 1980

Information:


Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     150-3992     Timing Pin (1)     1    
150-3993 Timing Pin (2)     1    
( 1 ) The timing pin is required in order to install Bosch fuel injection pumps.
( 2 ) The timing pin is required in order to install Lucas and Stanadyne fuel injection pumps.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00567719
Typical example
Check the condition of O-ring seal (1) from fuel injection pump (2). If the seal is worn or damaged, use a new part for replacement.
Lightly lubricate O-ring seal (1) with clean engine oil. Install O-ring seal (1) on fuel injection pump (2) .
The number 1 cylinder must be at the top center position on the compression stroke before the fuel injection pump is installed. If the crankshaft needs to be rotated, the fuel injection pump must be mounted temporarily or the loose gear could cause damage to the front housing.
Illustration 2 g00567718
Typical example
Put fuel injection pump (2) in position on the engine. Ensure that the timing gear is aligned with the hub of fuel injection pump (2). Install three nuts (3) and tighten the nuts to a torque of 28 N m (21 lb ft).
Illustration 3 g00567717
Typical example
Illustration 4 g00567737
Typical example
Position gear (5) on the shaft of the fuel injection pump.
Put the timing gear plate in position and install four bolts (4). Tighten the four bolts finger tight.Note: The fuel injection pump gear will only fit in one position. Install the gear with the letters "C" and "M" facing away from the engine.Note: The location of Tool (A) for Bosch fuel injection pumps will be located toward the top of the fuel injection pump. The location of Tool (A) for Lucas and Stanadyne fuel injection pumps will be located toward the bottom of the fuel injection pump.
Install Tool (A) through hole (6) in the timing gear and hole (7) in the hub. Push Tool (A) into position in hole (8) in the fuel injection pump body. If Tool (A) can be fully seated, the fuel injection pump timing is correct. No resistance should be felt when the timing pin is inserted into hole (8) of the fuel injection pump body.
The fuel injection pump may be supplied with the fuel injection pump shaft in the locked position. The drive shaft of the fuel injection pump must not be rotated without the spacer in position under the locking screw. Damage to the drive shaft of the fuel injection pump will result.
When the timing plate is installed, rotate gear (5) by hand in a counterclockwise direction in order to remove the backlash between gear (5) and the idler gear. Do not rotate the crankshaft or the fuel injection pump shaft. Tighten bolts (4) to a torque of 28 N m (21 lb ft).
Remove Tool (A) from the fuel injection pump gear.End By:
Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines - Remove and Install".
Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".


Parts motor JOHNSON:

0582061
 
0582061 MOTOR CABLE ASSY
50R79C, 55E79C, J40ECRM, J50BECIC, J50BECNR, J50BECRM, J50BECTA, J50ECSR, J55RCIM, J55RLCSA, J60ECIA, J60ECNM, J60ECSR, J60ECTB, J60ELCRE
0324963
 
0324963 MOTOR COVER,Lower
50R79C, 55E79C, J50ECSR, J55RLCSA, J60ECSR
0390313
 
0390313 MOTOR COVER ASSY.
J55RLCSA, J60ECSR
0391599
 
0391599 MOTOR COVER,Lower
J55RLCSA, J60ECSR
Back to top