5032670 JOHNSON MOTOR Assy, TRIM & TILT


5032670 MOTOR Assy, TRIM & TILT JOHNSON BJ40PL4SRS, BJ50PL4SRS, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC MOTOR
5032670 MOTOR Assy, TRIM & TILT JOHNSON
Rating:
106

Buy MOTOR Assy, TRIM & TILT 5032670 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$109.69

13-01-2025
3.1526[1.42] Pounds
CN: Marine Parts Manufac
Outboard Engine 38100-87J10 38100-87J11 87J12 87J20 87J21 Tilt Trim Motor for Suzuki 40HP 50HP / 8M6007533 for Mercury / 5032670 for Evinrude Johnson OMC / 36120-ZV5-822 for Honda, 18-6793 for Sierra
SouthMarine Fit Engine: 40HP 50HP BF40A2 LHTA BF40A3 XRTA DF40 DF50 DT40 || For Evinrude Johnson BJ40PL4 2004, BJ50PL4 2004, E40PL 2001, E50PL 2001, J40PL4 2002-2004, J50PL4 2002-2004; For Honda BF40 2002-2003, BF50 2002-2003; For Suzuki DF40QHL 2001-2002, DF40TL 2001-2010, DF50QHL 2001-2002, DF50TL 2001-2010 || Fit Part Number: for API Marine: PT656NM, for Arrowhead: TRM0085, for EMP Parts: 4-6793, for Honda: 36120-ZV5-822, for J & N: 430-22078, for Lester: 10861, for OMC: 5032670, for Sierra Marine: 18-6793, for Suzuki: 38100-87J10, 38100-87J11, 38100-87J12, 38100-87J20, 38100-87J21, for WAI: 10861N, for Mercury 8M6007533 || Voltage: 12V || If you are unsure, please provide your engine serial number.
$99.99
 

19-09-2022
1.65 Kilograms
-: -
36120-ZV5-822 Tilt Trim Motor For HONDA Outboard Motor SUZUKI 38100-87J10 OMC 5032670 40 50HP 4 Stroke Lester 10861 Boat Engine
OEM:36120-ZV5-822 38100-87J10 || 36120-ZV5-822 Tilt Trim Motor For HONDA Outboard Motor || High quality
$82.00
 

28-09-2023

-: -
NC 38100-87J11 Tilt Trom Motor for Suzuki OMC 5032670 40 50HP 4 Stroke Lester 10861 Boat Motor
Number on catalog scheme: 1
 

BRP JOHNSON entire parts catalog list:

Information:

Probable Causes
Active codes and logged codes
Electrical connections
Unstable fuel supply
Switches
Circuit protection
Engine speed/timing
Table 1
Associated Diagnostic Trouble Codes
J1939 Code CDL Code
3719-0 E995 (3)
3719-16 E995 (2) Recommended Actions
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Table 2
Troubleshooting Test Steps Values Results
1. Active Codes and Logged Codes
A. Certain diagnostic codes and/or event codes may cause an engine shutdown. Connect the electronic service tool and check for active codes and for logged codes.
B. Use the electronic service tool to check for associated diagnostic trouble codes. Refer to Table 1
Codes
Result: There are associated diagnostic trouble codes active or logged.
Repair: Troubleshoot any active or logged associated diagnostic trouble codes before continuing with this procedure.
Result: There are no associated diagnostic trouble codes active or logged.
Proceed to Test Step 2.
2. Electrical Connections
A. Check for the correct installation of the ECM J1/P1 and the J2/P2 connectors. Check for correct installation of the fuel injector connectors.
Connectors
Result: There are suspect connectors.
Repair: Perform the "Wiggle Test" on the electronic service tool.
Repair or replace connectors that are suspect.
Result: There are no suspect connectors.
Proceed to Test Step 3.
3. Electrical Connections
A. Check the power and ground connections to the ECM. Refer to Troubleshooting, "Electrical Power Supply - Test".
Electrical Connectors
Result: The electrical connections are OK.
Proceed to Test Step 4.
Result: The electrical connections are not OK.
Repair: Repair or replace the damaged connectors. Verify that the repair eliminated the fault.
4. Unstable Fuel Supply
A. Inspect the fuel system. Refer to Systems Operation/Testing and Adjusting, "Fuel System - Inspect" for additional information.
Cold weather adversely affects the characteristics of the fuel. Refer to the engine Operation and Maintenance Manual, "Cold Weather Operation" for further information.
B. Check fuel quality. Check the fuel tank for debris or foreign objects which may block the fuel supply.
Fuel
Result: The fuel quality is OK.
Proceed to Test Step 5.
Result: The fuel quality is not OK.
Repair: Replace the fuel. Verify that the repair eliminated the fault.
5. Switches
A. Check the keyswitch input to the ECM.
B. Check any engine shutdown switches and associated wiring.
Switches
Result: The shutdown switches and wiring are OK.
Proceed to Test Step 6.
Result: The shutdown switches and wiring are not OK.
Repair: Make the necessary repairs, Verify that the repair eliminated the fault.
6. Circuit Protection
A. Inspect the wires and connectors to all circuit protection for the engine.
B. Check the device for circuit protection.
Circuit protection
Result A circuit protection device is tripped.
Repair: Reset the circuit breaker if a circuit breaker is tripped. If necessary, replace blown fuses. Prior to returning the engine to service, determine the condition that caused the circuit breaker to trip or the fuse to blow. Make the necessary repairs.
Result The circuit protection is OK.
Proceed to Test Step 7.
8. Engine Speed/Timing Sensors
A. Inspect the connectors for the engine speed/timing sensors.
B. Crank the engine. If the engine starts and no speed timing codes are logged, the speed timing circuit is operating correctly.
Speed/Timing
Result: The Speed/Timing sensor circuit is not operating correctly.
Repair: Test the speed/timing circuit. Refer to Troubleshooting, "Speed/Timing `- Test". Verify that the repair eliminated the fault.
If the fault is still present, contact the Dealer Solutions Network (DSN).


Parts motor JOHNSON:

5032433
MOTOR Assy, STARTER
5032433 MOTOR Assy, STARTER
BJ40PL4SRS, BJ50PL4SRS, BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, J40PL4SNF, J40PL4STC, J50PL4SNF, J50PL4STC, J60PL4SNF, J70PL4SNF
Back to top