0377963 JOHNSON MOUNT, Rubber, upper front


0377963 MOUNT, Rubber, upper front JOHNSON 40E69R, 40E70A, 40ES69R, 40ES70A, 40R69R, 40R70A, RD-30A, RDS-30A, RK-30A MOUNT
0377963 MOUNT, Rubber, upper front JOHNSON
Rating:
93

Buy MOUNT, Rubber, upper front 0377963 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$6.79
 

20-03-2021

-: -
OMC Rubber Mount P/N 377963 0377963 NOS
Number on catalog scheme: 24
 

BRP JOHNSON entire parts catalog list:

40E69R, 40EL69R 1969
40E70A, 40EL70A 1970
40ES69R, 40ESL69R 1969
40ES70A, 40ESL70A 1970
40R69R, 40RL69R 1969
40R70A, 40RL70A 1970
RD-30A, RD-30D, RD-30S, RDL-30A, RDL-30D, RDL-30S 1968
RDS-30A, RDS-30C, RDS-30D, RDS-30S, RDSL-30A, RDSL-30C, RDSL-30D, RDSL-30S 1968
RK-30A, RK-30C, RK-30D, RKL-30A, RKL-30C, RKL-30D 1968

Information:


Table 1
Diagnostic Codes Table    
Code and Description    Conditions which Generate this Code    System Response    
268-2 Programmed Parameter Fault erratic, intermittent, or incorrect     The engine's Electronic Control Module (ECM) detects that one or more of the programmable parameters have not been programmed.     The ECM will set the unprogrammed parameter(s) to a default value.
The code is logged.    If the 268-02 diagnostic code is active, program the missing parameter.System configuration parameters are parameters that affect emissions, power of the engine, and machine applications. Default values for the parameters are programmed at the factory. Some parameters may be changed by the customer in order to suit the needs of the specific application. You must reprogram the system configuration parameters if the ECM is replaced and/or if you reprogram the engine rating. Values for these parameters are available on Caterpillar Electronic Technician (ET). Certain configuration parameters are also stamped on the engine information plate.Parameter Descriptions
"Equipment ID"
The "Equipment ID" parameter allows the customer to enter a description into the ECM in order to identify the machine. A maximum of 17 characters can be entered in the field."Engine Serial Number"
Program the "Engine Serial Number" to match the engine serial number that is stamped on the engine information plate. The engine serial number is not preprogrammed on a replacement ECM."FLS" (Full Load Setting)
"FLS" is a number that represents the adjustment to the fuel system that was made at the factory in order to fine tune the fuel system. The correct value for this parameter is stamped on the engine information plate. Only change this value if the engine is rerated or if a new ECM is installed. The parameter allows one time of programming without a factory password. In order to change the "FLS" after the initial programming, factory passwords are required."FTS" (Full Torque Setting)
"FTS" is similar to "FLS". Only change this value if the engine is rerated or if a new ECM is installed. Factory passwords are required. A new ECM or a blank ECM allows one time of programming of the "FTS" without the use of factory passwords. In order to change the "FTS" after the initial programming, factory passwords are required.Parameter Table
Table 2
System Configuration Parameters    
Parameter    Available Range or Options    Default    Required Password    
"Equipment ID"     17 characters     N/A     None    
"Engine Serial Number"     8 characters     N/A     None    
ECM Part Number                
ECM Serial Number                
"FLS"     -128 to +127     0     Factory    
"FTS"     -128 to +127     0     Factory    
"Software Group Part Number"                
"Software Group Release Date"                
"Software Group Description"                Parameter Worksheet
Record the following information before you change any programmable parameter.
Table 3
Information from ECM    
"Equipment ID"    
   
"Engine Serial Number"    
   
ECM Part Number        
"ECM Serial Number"    
   
"FLS"    
   
"FTS"    
   
"Software Group Part Number"    
   
"Software Group Release Date"    
   
"Software Group Description"    
   
"Total Tattletale"    
   
Injector Code 1        
Injector Code 2        
Injector Code 3        
Injector Code 4        
Injector Code 5        
Injector Code 6        


Parts mount JOHNSON:

0379022
 
0379022 MOUNT, Rubber, side
40E69R, 40E70A, 40R69R, 40R70A, RD-30A, RDS-30A
0377964
 
0377964 MOUNT, Rubber, lower front
40E69R, 40E70A, 40ES69R, 40ES70A, 40R69R, 40R70A, RD-30A, RDS-30A, RK-30A
0379007
 
0379007 MOUNT, Rubber, side
40ES69R, 40ES70A, RK-30A
Back to top