0313360 JOHNSON NEEDLE VALVE, Slow speed


0313360 NEEDLE VALVE, Slow speed JOHNSON 55ES69A, 60ES70B, 60ES71C, TR-10R NEEDLE
0313360 NEEDLE VALVE, Slow speed JOHNSON
Rating:
93

Buy NEEDLE VALVE, Slow speed 0313360 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 30
 

Compatible models:

BRP JOHNSON entire parts catalog list:

55ES69A, 55ES69C, 55ESL69A, 55ESL69C 1969
60ES70B, 60ES70D, 60ESL70B, 60ESL70D 1970
60ES71C, 60ES71E, 60ESL71C, 60ESL71E 1971
TR-10R, TR-10S, TRL-10R, TRL-10S 1968

Information:

1. Disconnect two fuel lines (1) from the fuel transfer pump. 2. Remove two bolts (3) and fuel transfer pump (2).Install Fuel Transfer Pump
1. Put fuel transfer pump (1) in position and install the two bolts that hold it to the fuel pump housing. 2. Connect two lines (2) to the fuel transfer pump.Disassemble Fuel Transfer Pump
start by:a) remove fuel transfer pump 1. Remove bolts (1) that hold transfer pump cover (2) to transfer pump body (5).2. Remove bolts and clamps (4) from the tachometer drive adapter. Remove tachometer drive adapter (3) from the cover. 3. Remove lip type seal (6) from the cover. Remove plug and O-ring seal (7), seat (8), spring (9) and valve (10) from the cover. 4. Remove nut (14) on end of shaft (11) and remove gear (17) and key (12) from the shaft. Remove O-ring seal (13) and the shaft from the body (5).5. Remove idler gear (15) from shaft (16).6. Remove the bearings and the two lip type seals from the body.7. Remove the check valve and shaft (16) from the body.Assemble Fuel Transfer Pump
1. Clean the openings (ports) for the fuel passage in body (3).2. Install shaft (1) and check valve (2) in the body with tooling (A).3. Install smaller bearing (4) in the body with tooling (B). Install the bearing until it is even with the machined surface of the body. 4. Install seal (5) in the body with tooling (C). Install the seal until it is .969 in. (24.6 mm) from the top surface of the body and with the lip toward bearing (4) as shown.5. Install seal (6) in body (3) with tooling (D). Install the seal until it is .563 in. (14.3 mm) from the top surface of the body and with the lip toward the top surface of body (3) as shown. 6. Install the large bearing in body (3) with tooling (E). Install the bearing even with the outside surface of the body. 7. Install the seal in cover (7) with tooling (C). Install the seal with the lip toward the inside of the cover and until it is .750 in. (19.1 mm) below the outside surface of the cover.8. Install the fuel bypass valve, the valve, spring, seal, O-ring seal and plug (14) in the cover. Tighten the plug to a torque of 27 3 lb.ft. (38 4 N m).9. Install shaft (9) in the body. Install gear (13) on the shaft to make an alignment with the gear on the shaft.10. Put 7M7260 Liquid Gasket Material on surface of cover (8). Install the cover on the body.
Do not let liquid gasket material enter the pump.
11. Install the six bolts that hold the cover (7) to the body. Install the O-ring seal to the body. The shaft must turn freely after the bolts that hold the cover in position are tightened.12. Install key (12) on the shaft. Install gear (8) on shaft and in alignment over the key. Install nut (11) on the shaft. Tighten the nut to a torque of 22 5 lb.ft. (28 7 N m).13. Install tachometer drive adapter (10) on the cover.end by:a) install fuel transfer pump


Parts needle JOHNSON:

0378251
 
0378251 NEEDLE BRG.,Wrist pin
100ESL71A, 100ESL72R, 115ESL69E, 115ESL70D, 125ESL71C, 125ESL72R, 20R69B, 20R70C, 20R71S, 20R72R, 20R73A, 25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 25E77S, 25E78C, 25E79R, 25R69B, 25R70C, 25R71S, 33E69A, 33E69A, 33E70M, 33E70M, 35E76G, 35E77C, 35E78R,
0378515
 
0378515 NEEDLE SET,Rod bearing
100ESL71A, 100ESL72R, 115ESL69E, 115ESL70D, 115ESL73M, 125ESL71C, 125ESL72R, 135ESL73M, 33E69A, 33E69A, 33E70M, 33E70M, 40E69R, 40E70A, 40E71B, 40E72E, 40E73D, 40E74S, 40ES69R, 40ES70A, 40R69R, 40R70A, 50ES71S, 50ES72C, 50ES73R, 50ES74M, 55ES69A, 60E
0382407
NEEDLE BEARING ASSEMBLY
0382407 NEEDLE BEARING ASSEMBLY
100ESL71A, 100ESL72R, 100ML79S, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL7
0377135
 
0377135 NEEDLE BEARING ASSY
115ESL69E, 115ESL70D, 55ES69A, 60ES70B, 60ES71C, 85ESL69E, 85ESL70B, TR-10R, V4A-20A, V4S-20A, V4T-14B, VX-14B
0379504
.NEEDLE BEARING ASSEMBLY
0379504 .NEEDLE BEARING ASSEMBLY
100ESL71A, 100ESL72R, 100ML79S, 115EL77S, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 50ES71S, 50ES72C, 50ES73R, 50ES74M, 50R79C, 55E79C, 60ES71
Back to top