5030288 JOHNSON NUT, Propeller


5030288 NUT, Propeller JOHNSON J4R4SDA, J4R4SOR, J4R4SRC, J4R4STS, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4STS, J5R4SUM, J5RECS, J5REEC, J5RLSIM, J5RLSSA, J6R4SDC, J6R4SOS, J6R4SUR NUT
5030288 NUT, Propeller JOHNSON
Rating:
13

Buy NUT, Propeller 5030288 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 5
 

BRP JOHNSON entire parts catalog list:

J4R4SDA, J4RL4SDA 2006
J4R4SOR, J4RL4SOR 2005
J4R4SRC, J4RL4SRC 2004
J4R4STS, J4RL4STS 2003
J4R4SUM, J4RL4SUM 2007
J5R4SDA, J5RL4SDA 2006
J5R4SOR, J5RL4SOR 2005
J5R4SRC, J5RL4SRC 2004
J5R4STS, J5RL4STS 2003
J5R4SUM, J5RL4SUM 2007
J5RECS, J5RLECS 1998
J5REEC, J5RLEEC 1999
J5RLSIM, J5RSIM, J5RVLSIM, J5RVSIM 2001
J5RLSSA, J5RSSA 2000
J6R4SDC, J6RL4SDC 2006
J6R4SOS, J6RL4SOS 2005
J6R4SUR, J6RL4SUR 2007

Information:


Illustration 1 g01181798
Schematic for the engine speed/timing sensors
Test Step 1. Check for Diagnostic Codes
Connect Cat ET to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools".
Restore electrical power to the engine ECM.
Start the engine and run the engine until the engine is at the normal operating temperature. Note: If the engine will not start, monitor the engine rpm on Cat ET while the engine is being cranked. Cat ET may need to be powered from another battery while the engine is being cranked.
Wait at least 30 seconds for activation of the diagnostic codes. Look for these codes on Cat ET:
190-02
190-11
342-02
342-11Expected Result:One or both of the diagnostic codes that are listed above are logged or active.Note: If the engine will not start and Cat ET displayed 0 rpm during cranking, select "No Engine rpm".Results:
No Engine rpm - Engine rpm is not indicated on Cat ET. Proceed to Test Step 2.
Active or logged code - There is an active diagnostic code or a logged diagnostic code for an engine speed/timing sensor. Proceed to Test Step 4.
No codes - Neither code is active or logged.Repair: Refer to the appropriate symptoms in Troubleshooting, "Troubleshooting Without a Diagnostic Code".STOPTest Step 2. Check the Installation of the Sensor Assembly
Remove electrical power from the engine ECM.
Illustration 2 g01180490
Left side view
(1) Engine
(2) Mounting flange
(3) Bracket
Visually inspect the sensor assembly without removing the sensor assembly from the engine. Flanges (2) must be flush against engine (1) in order to ensure proper operation. Inspect bracket (3). Verify that the bracket securely holds the flanges of the sensors flush against the engine.Verify that the bracket is not bent. If the bracket is bent or if an obstruction is preventing the sensor assembly from being installed correctly, the engine will not start.Note: The bracket cannot be replaced separately.
Remove the sensor assembly from the engine.
Illustration 3 g01180501
Exploded view of the engine speed/timing sensors
(4) O-ring seals
Ensure that one O-ring (4) is installed on each sensor. Check the O-rings for damage. Replace the O-rings, if necessary. Results:
OK - The sensor assembly's components are OK.Repair: Perform the following procedure in order to properly install the sensor assembly:
Lubricate each O-ring with engine oil.
Fully seat the sensor assembly in the engine. Note: If the sensor assembly will not fully seat into the engine, replace the sensor assembly.
Tighten the bracket bolt.
Connect the sensor's electrical connectors. Verify that the connectors are latched on both sides.
Ensure that the harness is properly secured, and that the tie-wraps are placed in the correct location. Proceed to Test Step 3.
Not OK - At least one of the sensor assembly's components is not OK.Repair: Obtain a new sensor assembly. Perform the following procedure in order to properly install the sensor assembly:
Lubricate each O-ring with engine oil.
Fully seat the sensor assembly in the engine. Note: If the sensor assembly will not fully seat into the engine, replace the sensor assembly.
Tighten the bracket bolt.
Connect the sensor's electrical connectors. Verify that the connectors are latched on both sides.
Ensure that the harness is properly secured, and that the tie-wraps are placed in the correct location. Verify that the problem is resolved.STOPTest Step 3. Inspect the Electrical Connectors and the Wiring
Illustration 4 g01181799
Left side engine view (typical example)
(5) J401/P401 connector for the primary engine speed/timing sensor
(6) J402/P402 connector for the secondary engine speed/timing sensor
(7) J2/P2 ECM connector
Thoroughly inspect connectors (5), (6), and (7). Refer to Troubleshooting, "Electrical Connectors - Inspect".
Illustration 5 g01181800
Left side view
(P2-48) Primary engine speed/timing sensor +
(P2-49) Primary engine speed/timing sensor -
(P2-58) Secondary engine speed/timing sensor +
(P2-59) Secondary engine speed/timing sensor -
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the engine speed/timing sensors.
Check the allen hea


Parts nut JOHNSON:

5030018
NUT, Bolt, fuel tank
5030018 NUT, Bolt, fuel tank
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS, J25PL4SOC, J25PL4SRS, J30PL4SDR, J
5030051
 
5030051 NUT, Stud, water pump housing
BJ115L4STS, BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, BJ
5030019
 
5030019 NUT, Flywheel
J2R4SDS, J5RECS, J5REEC, J5RLSIM, J5RLSSA
5030224
NUT
5030224 NUT
BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, J10BL4SUM, J10EL4SDA, J10EL4SOR, J10EL4SRC, J10R4SDM, J10R4SNF, J10R4SR, J10R4STC,
5030017
 
5030017 NUT, Screw, lever
J5RECS, J5REEC, J5RLSSA
5030052
 
5030052 NUT, Shaft to handle
BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, J10R4SNF, J140CX4STS, J140PL4STS, J15R4SNF, J4R4STS, J5R4STS, J5RECS, J5REEC, J5RLSSA, J60PL4SNF, J70FLTLECS, J70PL4SNF
5030053
 
5030053 NUT, Throttle adjustment knob
J10EL4SOR, J10R4SDM, J10R4SUB, J10RL4SDM, J10TBL4SDE, J10TBL4SUD, J10TE4SDM, J15EL4SOS, J15R4SDM, J15R4SUB, J15RL4SDM, J15TE4SDM, J15TE4SUB, J4R4SDA, J4R4SOR, J4R4SRC, J4R4SUM, J5R4SDA, J5R4SOR, J5R4SRC, J5R4SUM, J5RECS, J5REEC, J5RLSIM, J5RLSSA, J6R
5030054
NUT, Bolt, stern brackets
5030054 NUT, Bolt, stern brackets
BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, J10EL4SRC, J10R4SNF, J10R4SR, J10R4STC, J15R4SNF, J15R4SR, J15R4STC, J15RL4SR, J25PL4SOC, J25PL4SRS, J30PL4SDR
Back to top