5031986 JOHNSON O RING, OIL PUMP


5031986 O RING, OIL PUMP JOHNSON J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA O
5031986 O RING, OIL PUMP JOHNSON
Rating:
58

Buy O RING, OIL PUMP 5031986 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 3
 

BRP JOHNSON entire parts catalog list:

J25PL4SOC, J25TEL4SOC 2005
J25PL4SRS 2004
J30PL4SDR 2006
J30PL4SOC, J30TEL4SOC 2005
J30PL4SRS 2004
J30PL4SUA 2007
J30TEL4SDR 2006
J30TEL4SUA 2007

Information:

Parameter Descriptions
Rating Number
The rating number corresponds to the selected set of performance maps that has been selected for this application. There may be more than one set of performance maps that are available for this engine. All of the maps are resident in the flash file for the engine.Rated Frequency
The line frequency of the generator setRated Engine Speed
The optimum speed of the engineRated Real Genset Power
The output power of the generator set in kilowattsRated Apparent Genset Power
The kVA rating of the generator setRating Configuration
The performance maps in the softwareTest Spec
This is the engine's "Test Specifiction Number". Use this number to retrieve data that is related to the engine's specifications from the Technical Marketing Information System (TMI). The following information can be retrieved from TMI:
"As shipped consists"
"Engine test specifications"
"Systems data"
"Physical data"
"Gasket kit data"
"Reman parts"
"Performance data"A link to TMI Web can be found on the web site for the Service Information System (SIS).Equipment ID
This parameter allows the customer to enter a description into the ECM in order to identify the engine's application. A maximum of 17 characters can be entered in the field.Engine Serial Number
The engine serial number must be programmed to match the engine serial number that is stamped on the engine information plate. The engine serial number is not preprogrammed into a replacement ECM.ECM Serial Number
The serial number of the ECM that is stored in the ECM memorySoftware Group Part Number
The part number of the flash file that is currently installed in the ECMSoftware Group Release Date
The release date of the flash file that is currently installed in the ECMSoftware Group Description
The description of the application for the flash file that is currently installed in the ECMTotal Tattletale
The total tattletale counts the number of changes to system parameters.Engine Accel. Rate
This parameter defines the maximum rate of engine acceleration.Low Idle Speed
This parameter defines the low idle rpm of the engine.Engine Speed Droop
This parameter enables the engine to be operated in a load sharing system.Droop/Isochronous Switch Enable
This parameter defines the installation status of a switch that is used to select droop or isochronous mode.Droop Mode Selection
This parameter allows the customer to select droop or isochronous mode.Ether Control
This parameter defines the installation status of an ether starting aid for the engine.Engine Oil Temperature Sensor Installation Status
This parameter defines the installation status of an engine oil temperature sensor.Desired Speed Input Configuration
This parameter defines the type of signal that is used for throttle control. This parameter will be used while a valid signal is present at the expected input.The following input types are available:"PWM" - A Pulse Width Modulated signal (PWM) is received via terminal P1-66 at the ECM connector."CAN Input" - A J1939 signal is received via the CAN data link."0 - 5 VDC" - An analog signal is received via terminal P1-17 at the ECM connector.Secondary Desired Speed Input Configuration
This parameter defines the type of signal that is used as a secondary throttle control. If the signal that is defined for Desired Speed Input Configuration becomes unavailable, the ECM will revert to this type of signal for the throttle control. Refer to "Desired Speed Input Configuration" for the input types that are available.Fuel Enable Input Configuration
This parameter allows the selection for the type of input that is used to enable the fuel for the engine.Secondary Fuel Enable Input Configuration
This parameter sets the installation status of a secondary switch that can be used to enable the fuel for the engine.Fuel Filter Differential Pressure Switch Configuration
This parameter sets the installation status of a fuel filter differential pressure switch for the engine.Emergency Shutdown Override Switch Installation Status
This parameter sets the installation status of an engine shutdown override switch.Emergency Shutdown Override Switch Configuration
This parameter sets the configuration of an engine shutdown override switch.FLS
"FLS" is a parameter that represents the fuel system adjustment that was made at the factory in order to fine tune the fuel system to the engine. The correct value for this parameter is stamped on the engine information plate. Only change this value if the engine is rerated or if a new ECM has been installed. Factory passwords are required to change this parameter.FTS
"FTS" is another parameter that represents a fuel system adjustment that was performed at the factory in order to fine tune the fuel system to this engine. Only change this value if the engine is rerated or if a new ECM has been installed. Factory passwords are required to change this parameter.Governor Gain Factor
This parameter is used in determining the engine's rate of response to an engine load.Governor Minimum Stability Factor
This parameter is used by the ECM to offset the steady state speed error when the steady state speed error is less than 20 rpm.


Parts o JOHNSON:

0334913
O-RING, Fuel connector
0334913 O-RING, Fuel connector
AM55RSLD, BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ130PLSSS, BJ135PLSIF, BJ15EEDS, BJ15FAEDR, BJ15FAEUA, BJ15FDLECM, BJ15RELEUC, BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25ARECA, BJ2
5030541
 
5030541 O-RING, Cap
BJ115L4SDA, BJ115L4SRC, BJ115L4STS, BJ140CX4DR, BJ140CX4SRS, BJ140L4SDR, BJ140PL4SRS, BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, BJ40PL4SDR, BJ40PL4SOC, BJ40PL4SRS, BJ50PL4SDR, BJ50PL4SOC, BJ50PL4SRS, BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4S
5030539
O-RING, Water pipe
5030539 O-RING, Water pipe
BJ60PL4SDM, BJ60PL4SOA, BJ60PL4SRR, BJ60PL4STC, BJ70PL4SDM, BJ70PL4SOA, BJ70PL4SRR, BJ70PL4STC, J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA, J60PL4SNF, J70FLTLECS, J70PL4SNF
5032379
*O RING
5032379 *O RING
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5032389
*O RING
5032389 *O RING
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5031507
 
5031507 *O RING SET
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA
5032367
 
5032367 *O RING
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA
5032369
O RING
5032369 O RING
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA
Back to top