5035041 PANEL, PUMP CASE UNDER JOHNSON
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS
PANEL
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
RUIJADE 17400-93J02 Water Pump Repair Kit Compatible with Suzuki Outboard 200/225/250HP Sierra 18-3264
RUIJADE 😀【 17400-93J02】 This is Top Quality Aftermarket Outboard Impeller Water Pump Repair Kit. Fits Suzuki 17400-93J02, Sierra 18-3264. || 😀【Kit Includes】 Water Pump Impeller 18-3035 17461-93J00, 5035040. Wear Plate 17471-93J02, 17474-93J01, 5035041. Seal 17416-93J00, 5035039. Key 09420-05009. Gasket 17472-93J00 18-0778, 5035042 as pictures showed. || 😀【Applications】 This water pump rebuild kit fits suzuki outboard 4 stroke 200hp 225hp 250HP V6 boat motors engine parts model DF200 DF225 DF300 boat accessories cooling system. || 😀【High Quality】 Made to meet or exceed OEM specifications. Extremely high quality metal alloys and modern neoprene which keep a spare in the toughest marine environment.
RUIJADE 😀【 17400-93J02】 This is Top Quality Aftermarket Outboard Impeller Water Pump Repair Kit. Fits Suzuki 17400-93J02, Sierra 18-3264. || 😀【Kit Includes】 Water Pump Impeller 18-3035 17461-93J00, 5035040. Wear Plate 17471-93J02, 17474-93J01, 5035041. Seal 17416-93J00, 5035039. Key 09420-05009. Gasket 17472-93J00 18-0778, 5035042 as pictures showed. || 😀【Applications】 This water pump rebuild kit fits suzuki outboard 4 stroke 200hp 225hp 250HP V6 boat motors engine parts model DF200 DF225 DF300 boat accessories cooling system. || 😀【High Quality】 Made to meet or exceed OEM specifications. Extremely high quality metal alloys and modern neoprene which keep a spare in the toughest marine environment.
MARKGOO 17400-93J04 Water Pump Impeller Repair Kit for Suzuki Outboard 4 Stroke 200/225/250 HP DF200 DF225 DF250 V6 Boat Motor Engine Rebuild Service Parts Replacement Sierra Marine 18-3264
MARKGOO This water pump rebuild kit fits suzuki outboard 4 stroke 200hp 225hp 250HP V6 boat motors engine parts model DF200 DF225 DF300 boat accessories cooling system. It is very important to check your boat motor part number before purchase. please message us engine year, s/n and horsepower if you are not sure. || The water pump impeller repair or service kit for Suzuki outboard OEM p/n 17400-93J00, 17400-93J01, 17400-93J02, 17400-93J03, 17400-93J04. More detailed information please see description below. || Also fits Johnson Evinrude OMC outboard 4 storke EFI 200/225 HP (2004-2005) 5035036 5035037 5035040 0769611. Designed for durability to provide higher flow rates and cooling flow to protect your engine, it makes repair and maintenance of water pumps easy. || Package included: Water Pump Impeller 18-3035 17461-93J00, 5035040. Wear Plate 17471-93J02, 17474-93J01, 5035041. Seal 17416-93J00, 5035039. Key 09420-05009. Gasket 17472-93J00 18-0778, 5035042 as pictures showed. || To find the correct water pump repair kit replacement for your suzuki outboard, it is VERY IMPORTANT to check your outboard model or s/n before purchase. you can leave us messages such as your boat engine model, horsepower or year if you're not sure. we 're pleasure to help you.
MARKGOO This water pump rebuild kit fits suzuki outboard 4 stroke 200hp 225hp 250HP V6 boat motors engine parts model DF200 DF225 DF300 boat accessories cooling system. It is very important to check your boat motor part number before purchase. please message us engine year, s/n and horsepower if you are not sure. || The water pump impeller repair or service kit for Suzuki outboard OEM p/n 17400-93J00, 17400-93J01, 17400-93J02, 17400-93J03, 17400-93J04. More detailed information please see description below. || Also fits Johnson Evinrude OMC outboard 4 storke EFI 200/225 HP (2004-2005) 5035036 5035037 5035040 0769611. Designed for durability to provide higher flow rates and cooling flow to protect your engine, it makes repair and maintenance of water pumps easy. || Package included: Water Pump Impeller 18-3035 17461-93J00, 5035040. Wear Plate 17471-93J02, 17474-93J01, 5035041. Seal 17416-93J00, 5035039. Key 09420-05009. Gasket 17472-93J00 18-0778, 5035042 as pictures showed. || To find the correct water pump repair kit replacement for your suzuki outboard, it is VERY IMPORTANT to check your outboard model or s/n before purchase. you can leave us messages such as your boat engine model, horsepower or year if you're not sure. we 're pleasure to help you.
Number on catalog scheme: 5
Compatible models:
BRP JOHNSON entire parts catalog list:
- WATER PUMP » 5035041
BJ225CX4DC 2006
BJ225X4SDC 2006
BJ200CX4O, J200CX4SOC 2004,2005
J200CX4SRS 2004
BJ200X4SO, J200PX4SOC 2004,2005
J200PX4SRS 2004
BJ225CX4O, J225CX4SOC, J225CZ4SOS 2004,2005
J225CX4SRS 2004
BJ225X4SO, J225PX4SOC, J225PZ4SOS 2004,2005
J225PX4SRS 2004
Information:
Illustration 1 g01173985
Schematic diagram of the output for the shutdown lampThe engine is equipped with a 70 pin connector.
Illustration 2 g01165014
Schematic diagram of the output for the shutdown lampThe engine is equipped with a remote control panel.
Illustration 3 g01165016
Schematic diagram of the output for the shutdown lampThe engine is not equipped with a remote control panel.Test Step 1. Inspect the Electrical Connectors and the Wiring
Set the engine control to the OFF/RESET mode. Remove the electrical power from the engine.Note: For the following steps, refer to Troubleshooting, "Inspecting Electrical Connectors".
Thoroughly inspect each of the following connectors:
EIS connectors on the control module
Connections for the equipment that is connected to the output for the shutdown lamp
Illustration 4 g01047029
Harness side of the EIS connector (EISC-D) Output for the shutdown lamp
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the output for the shutdown lamp.
Check the terminal strips for corrosion and for mechanical failure.
If the engine is equipped for CSA, check the harnesses and the wiring for abrasion and for pinch points between the device that is connected to the output and the control module.Expected Result:The connectors, pins, and sockets are connected properly. The terminal strips do not have corrosion or mechanical failure. The connectors and the wiring do not have corrosion, abrasion, or pinch points.Results:
OK - The components are in good condition with proper connections.
Not OK - The components are not in good condition and/or at least one connection is improper.Repair: Perform the necessary repairs and/or replace parts, if necessary.STOPTest Step 2. Check for an Open Circuit
Disconnect the EIS connector.
At the output device, identify the wire that runs to the EIS control module. Disconnect the end of the wire from the device. This will isolate the wire.
Check the continuity of the wiring between terminal EISC-D and the end of the wire that was removed from the output device.Expected Result:The wiring has continuity.Results:
OK - The wiring has continuity.Repair: Perform the following procedure:
Check the continuity of the output device. If the output device does not have continuity, replace the output device. STOP.
Check the continuity of the wiring between the output device and +Battery. If the wiring does not have continuity, repair the wiring or replace the wiring. STOP.
Reconnect the end of the wire to the output device. Restore electrical power to the engine and check the operation of the output for the shutdown lamp. If the output operates correctly, the problem is resolved. STOP. If the output does not operate correctly, proceed to Test Step 3.
Not OK - The wiring does not have continuity.Repair: Repair the connection and/or the wire, when possible. Replace parts, if necessary. Verify that the problem is resolved.STOPTest Step 3. Check for a Short Circuit
Verify that electrical power is removed from the engine.
Verify that the EIS connector is disconnected.
At the output device, identify the wire that runs to the EIS control module. Disconnect the end of the wire from the device. This will isolate the wire.
Measure the resistance between terminal EISC-D and all of the other terminals on the EIS connector.Expected Result:All of the measurements indicate an open circuit.Results:
OK - All of the measurements indicate an open circuit.Repair: Perform the following procedure:
Check the output device for a short circuit. If the output device has a short circuit, replace the output device. STOP.
If the output device does not have a short circuit, reconnect all of the wiring and the connectors.
Restore the electrical power to the engine. Determine if the problem is resolved. If the problem is resolved, STOP. If the problem is not resolved, proceed to Test Step 4.Test Step 4. Perform a Self Test of the EIS Control Module
Perform the self test for the EIS control module. Refer to Troubleshooting, "Control Module Self Test".Expected Result:The self test was successful.Results:
OK - The self test was successful.Repair: If the problem persists, refer to Troubleshooting, "Inspecting Electrical Connectors".STOP
Not OK - The self test was not successful.Repair: Perform the corrective action that is appropriate for the fault. Refer to Troubleshooting, "Control Module Self Test". Verify that the original problem is resolved.STOP
Parts panel JOHNSON:
5035202
5035202 PANEL, FRONT
BJ200CX4DC, BJ200X4SDC, BJ225CX4DC, BJ225X4SDC, J200CX4SOC, J200CX4SRS, J200PX4SOC, J200PX4SRS, J225CX4SOC, J225CX4SRS, J225PX4SOC, J225PX4SRS