0304377 PIN,Shift rod to lever JOHNSON
20R69B, 20R70C, 20R71S, 20R72R, 20R73A, 25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 25R69B, 25R70C, 25R71S, FD-22A, V4S-20A, VX-14B
PIN
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- LOWER UNIT GROUP » 0304377
20R71S, 20RL71S 1971
20R72R, 20RL72R 1972
20R73A, 20RL73A 1973
25E72R, 25EL72R, 25R72R, 25RL72R 1972
25E73A, 25EL73A, 25R73A, 25RL73A 1973
25E74M, 25EL74M, 25R74M, 25RL74M 1974
25E75B, 25EL75B, 25R75B, 25RL75B 1975
25E76E, 25EL76E, 25R76E, 25RL76E 1976
25R69B, 25R69D, 25RL69B, 25RL69D 1969
25R70C, 25R70E, 25RL70C, 25RL70E 1970
25R71S, 25RL71S 1971
FD-22A, FD-22E, FD-22M, FDL-22A, FDL-22E, FDL-22M 1968
V4S-20A, V4SL-20A 1968
VX-14B, VXH-14B, VXHL-14B, VXL-14B 1968
Information:
Introduction
Do not perform any procedure in this Special Instruction until you read this information and you understand this information.This Special Instruction describes the procedures for cleaning an engine that is saturated with fresh water. This Special Instruction does not apply to an engine that may have been saturated with salt water.Water Contamination
Note: If the engine is totally submerged, perform all of the Steps. If the water level did not get higher than the bottom of the cylinder heads perform Steps 9 through 26.Note: Perform the following steps as soon as possible once the engine is no longer submerged.
Drain the water from the inlet system and from the exhaust system.
Remove the aftercooler core and evacuate the water from below the aftercooler and from the air lines that are going to the cylinder heads.
Remove the air cleaners and drain water from turbochargers.
Remove the plug from the front or rear of the cylinder block. Evacuate the water that is under the plenum's cover.
Remove the air cleaners and install new air cleaners.
Remove the injectors and evacuate the water from the cylinders.
Use a borescope and check for rust or for contamination on top of the piston and inside the cylinder.
If there is not any rust or not any debris is evident, coat the walls of the cylinder with oil in order to prevent rust. If the engine will not be operated for several weeks, use VCI oil instead of engine oil.
Remove the camshaft covers and inspect the camshaft and the lifters for rust. If no rust is found spray parts with engine oil or a rust preventive. If the engine will not be operated for several weeks use VCI oil instead of engine oil.
Power up the engine but do not start the engine. Check for any diagnostic codes by using the Caterpillar Electronic Technician (ET). Replace the following components that may be damaged:
ECM
Sensors
Wiring harnesses
Drain the oil pan.
Remove the oil filters and install new oil filters.
Prelube the engine until all water is displaced from oil galleries.
Drain the oil pan.
Remove at least one of the side covers and clean the remaining mixture of water and oil from the oil pan. If the engine will not be operated for several weeks use a VCI oil instead of engine oil to coat the internal parts.
Remove the old oil filters and install new oil filters.
Fill the engine with new engine oil.
Start the engine and allow the engine to operate at no load for 15 minutes.
Drain the oil pan.
Remove the old oil filters and install new oil filters.
Clean the remaining mixture of oil and water from the oil pan.
Fill the engine with new engine oil.
Start the engine and allow the engine to operate at no load for 15 minutes.
Shut down the engine. Sample the engine oil for water.
If water is not present in the engine oil, cleaning is complete.
If water is present repeat Steps 19 through 24 until the water is not present in the engine oil sample.Note: Refer to the appropriate Reuse and Salvage Guidelines manual for reusability of parts that may have been damaged due to water entry. Notify the dealer's Technical Communicator (TC) in order to contact the Dealer Solution Network (DSN) if there are questions. Provide the appropriate photos and documentation.
Do not perform any procedure in this Special Instruction until you read this information and you understand this information.This Special Instruction describes the procedures for cleaning an engine that is saturated with fresh water. This Special Instruction does not apply to an engine that may have been saturated with salt water.Water Contamination
Note: If the engine is totally submerged, perform all of the Steps. If the water level did not get higher than the bottom of the cylinder heads perform Steps 9 through 26.Note: Perform the following steps as soon as possible once the engine is no longer submerged.
Drain the water from the inlet system and from the exhaust system.
Remove the aftercooler core and evacuate the water from below the aftercooler and from the air lines that are going to the cylinder heads.
Remove the air cleaners and drain water from turbochargers.
Remove the plug from the front or rear of the cylinder block. Evacuate the water that is under the plenum's cover.
Remove the air cleaners and install new air cleaners.
Remove the injectors and evacuate the water from the cylinders.
Use a borescope and check for rust or for contamination on top of the piston and inside the cylinder.
If there is not any rust or not any debris is evident, coat the walls of the cylinder with oil in order to prevent rust. If the engine will not be operated for several weeks, use VCI oil instead of engine oil.
Remove the camshaft covers and inspect the camshaft and the lifters for rust. If no rust is found spray parts with engine oil or a rust preventive. If the engine will not be operated for several weeks use VCI oil instead of engine oil.
Power up the engine but do not start the engine. Check for any diagnostic codes by using the Caterpillar Electronic Technician (ET). Replace the following components that may be damaged:
ECM
Sensors
Wiring harnesses
Drain the oil pan.
Remove the oil filters and install new oil filters.
Prelube the engine until all water is displaced from oil galleries.
Drain the oil pan.
Remove at least one of the side covers and clean the remaining mixture of water and oil from the oil pan. If the engine will not be operated for several weeks use a VCI oil instead of engine oil to coat the internal parts.
Remove the old oil filters and install new oil filters.
Fill the engine with new engine oil.
Start the engine and allow the engine to operate at no load for 15 minutes.
Drain the oil pan.
Remove the old oil filters and install new oil filters.
Clean the remaining mixture of oil and water from the oil pan.
Fill the engine with new engine oil.
Start the engine and allow the engine to operate at no load for 15 minutes.
Shut down the engine. Sample the engine oil for water.
If water is not present in the engine oil, cleaning is complete.
If water is present repeat Steps 19 through 24 until the water is not present in the engine oil sample.Note: Refer to the appropriate Reuse and Salvage Guidelines manual for reusability of parts that may have been damaged due to water entry. Notify the dealer's Technical Communicator (TC) in order to contact the Dealer Solution Network (DSN) if there are questions. Provide the appropriate photos and documentation.
Parts pin JOHNSON:
0303049
0303049 PIN, Cotter
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 20R70C, 20R73A, 25E73A, 25E74M, 25E75B, 25E76E, 25E77S, 25E78C, 25E79R, 25R69B, 25R70C, 33E69A, 33E69A, 33E70M, 33E70M, 35E76G, 35E77C, 35E78R, 35E79A, 4
0306463
0306463 PIN,Cotter,cam follower to manifold
25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 33E69A, 33E69A, 33E70M, 33E70M, 40E69R, 40E70A, 40E71B, 40E72E, 40E73D, 40E74S, 40E75C, 40E76A, 40ES69R, 40ES70A, 40R69R, 40R70A, FD-22A, RD-30A, RDS-30A, RK-30A, RX-16M, V4S-20A, V4T-14B, VX-14B
0307565
0307565 PIN,Link
25E77S, 25E78C, 25E79R, 33E69A, 33E69A, 33E70M, 33E70M, 35E76G, 35E77C, 35E78R, 35E79A, 40E69R, 40E70A, 40E71B, 40E72E, 40E73D, 40E74S, 40E75C, 40E76A, 40ES69R, 40ES70A, 40R69R, 40R70A, BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM
0309569
0310742
0552906
0552906 PIN,Cotter,trailer lock
100ML79S, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML78C, 140ML79R, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 65ES73R, 70EL76D, 70EL77S, 70EL78C, 70EL79
0316622
0316606