0319053 PIN,Link to locking lever JOHNSON
10E74G, 10E75C, 10E76G, 10E77A, 15E74G, 15E75C, 15E76A, 15E77M, 35E76G
PIN
Price: query
Rating:
Number on catalog scheme: 26
BRP JOHNSON entire parts catalog list:
- EXHAUST HOUSING » 0319053
10E76G, 10E76H, 10E76R, 10EL76G, 10EL76H, 10EL76R, 10R76G, 10R76H, 10R76R, 10RL76G, 10RL76H, 10RL76R 1976
10E77A, 10EL77A, 10R77A, 10RL77A 1977
15E74G, 15E74S, 15EL74G, 15EL74S, 15R74G, 15R74S, 15RL74G, 15RL74S 1974
15E75C, 15EL75C, 15R75C, 15RL75C 1975
15E76A, 15E76R, 15EL76A, 15EL76R, 15R76A, 15R76R, 15RL76A, 15RL76R 1976
15E77M, 15EL77M, 15R77M, 15RL77M 1977
35E76G, 35E76S, 35EL76G, 35EL76S, 35R76G, 35R76S, 35RL76G, 35RL76S 1976
Information:
Oil Pressure Test at Solenoid Valve
Work carefully around an engine that is running. Engine parts that are hot, or parts that are moving, can cause personal injury.
Table 1
Tools Needed
Part Number Part Name Quantity
149-6111 Oil Pressure Test Kit 1
Illustration 1 g00514378
149-6111 Oil Pressure Test Kit
(1) Pressure gauge
(2) Seals
(3) Control valve removal tool
(4) Control valve test body
(5) Control valve adapter
(6) Solenoid valve adapter
Attach pressure gauge (1) to solenoid valve adapter (6).
Remove the solenoid valve and the three seals from the compression brake housing. Refer to Disassembly and Assembly, "Compression Brake - Disassemble".
Install three seals (2), which are included in the 149-6111 Oil Pressure Test Kit. Place the smallest seal in the bottom of the bore for the solenoid. Install the other two seals on solenoid valve adapter (6).
Illustration 2 g00514470
Lubricate the seals with clean engine oil and install the adapter assembly in bore (7) for the solenoid valve. Hand tighten the adapter assembly and then tighten the adapter assembly for an additional 1/4 turn.
Start the engine. Ensure that the switch for the compression brake is in the OFF position.
Record the oil pressure reading.
Increase the engine speed by 400 rpm.
Repeat Steps 6 and 7 up to the rated engine rpm.
Stop the engine. Install the solenoid valve. Refer to Disassembly and Assembly, "Compression Brake - Assemble". Compare the oil pressure readings from the solenoid valve to the oil pressure readings from the Testing and Adjusting, "Control Valve (Compression Brake) - Test".
If the oil pressure at the solenoid valve is higher than the oil pressure at the control valve, continue with Steps 10 through 15.
If the oil pressure at the solenoid valve is the same pressure as the oil pressure at the control valve, the oil pressure to the compression brake is too low. Refer to Testing and Adjusting, "Engine Oil Pressure - Test".
Start the engine.
Disconnect the wires from each solenoid valve except for the solenoid valve that is being tested in order to check each solenoid valve individually.
Illustration 3 g00514472
Turn the switch for the compression brake to the ON position. Observe the movement of solenoid armature (8). The solenoid armature should snap down fully. Push down on the solenoid armature in order to verify that the solenoid is fully actuated. If the solenoid valve fully actuates, proceed to Step 14. Otherwise, continue to Step 13.
Check the voltage at the terminals on the solenoid valve. There should be at least ten volts at the terminals. Insufficient voltage at the terminals indicates that there are either poor connections in the circuit or that battery voltage is low. Verify proper battery voltage. Check the condition of the connections and clean the connections.Replace the solenoid valve if both of the following conditions exist:
The solenoid valve is receiving the correct voltage.
The solenoid valve does not actuate fully.
Look for excessive oil leakage from the bottom of the compression brake housing opposite the solenoid valve. While the solenoid valve is electrically actuated, leakage should be no more than two drops per second. Replace the solenoid valve if there is excessive leakage. Note: When the solenoid valve is deactivated, oil will dump from the solenoid valve. This is a normal condition that should not be confused with oil leakage while the solenoid valve is electrically actuated.
Repeat Steps 11 through 14 for each solenoid valve.
Work carefully around an engine that is running. Engine parts that are hot, or parts that are moving, can cause personal injury.
Table 1
Tools Needed
Part Number Part Name Quantity
149-6111 Oil Pressure Test Kit 1
Illustration 1 g00514378
149-6111 Oil Pressure Test Kit
(1) Pressure gauge
(2) Seals
(3) Control valve removal tool
(4) Control valve test body
(5) Control valve adapter
(6) Solenoid valve adapter
Attach pressure gauge (1) to solenoid valve adapter (6).
Remove the solenoid valve and the three seals from the compression brake housing. Refer to Disassembly and Assembly, "Compression Brake - Disassemble".
Install three seals (2), which are included in the 149-6111 Oil Pressure Test Kit. Place the smallest seal in the bottom of the bore for the solenoid. Install the other two seals on solenoid valve adapter (6).
Illustration 2 g00514470
Lubricate the seals with clean engine oil and install the adapter assembly in bore (7) for the solenoid valve. Hand tighten the adapter assembly and then tighten the adapter assembly for an additional 1/4 turn.
Start the engine. Ensure that the switch for the compression brake is in the OFF position.
Record the oil pressure reading.
Increase the engine speed by 400 rpm.
Repeat Steps 6 and 7 up to the rated engine rpm.
Stop the engine. Install the solenoid valve. Refer to Disassembly and Assembly, "Compression Brake - Assemble". Compare the oil pressure readings from the solenoid valve to the oil pressure readings from the Testing and Adjusting, "Control Valve (Compression Brake) - Test".
If the oil pressure at the solenoid valve is higher than the oil pressure at the control valve, continue with Steps 10 through 15.
If the oil pressure at the solenoid valve is the same pressure as the oil pressure at the control valve, the oil pressure to the compression brake is too low. Refer to Testing and Adjusting, "Engine Oil Pressure - Test".
Start the engine.
Disconnect the wires from each solenoid valve except for the solenoid valve that is being tested in order to check each solenoid valve individually.
Illustration 3 g00514472
Turn the switch for the compression brake to the ON position. Observe the movement of solenoid armature (8). The solenoid armature should snap down fully. Push down on the solenoid armature in order to verify that the solenoid is fully actuated. If the solenoid valve fully actuates, proceed to Step 14. Otherwise, continue to Step 13.
Check the voltage at the terminals on the solenoid valve. There should be at least ten volts at the terminals. Insufficient voltage at the terminals indicates that there are either poor connections in the circuit or that battery voltage is low. Verify proper battery voltage. Check the condition of the connections and clean the connections.Replace the solenoid valve if both of the following conditions exist:
The solenoid valve is receiving the correct voltage.
The solenoid valve does not actuate fully.
Look for excessive oil leakage from the bottom of the compression brake housing opposite the solenoid valve. While the solenoid valve is electrically actuated, leakage should be no more than two drops per second. Replace the solenoid valve if there is excessive leakage. Note: When the solenoid valve is deactivated, oil will dump from the solenoid valve. This is a normal condition that should not be confused with oil leakage while the solenoid valve is electrically actuated.
Repeat Steps 11 through 14 for each solenoid valve.
Parts pin JOHNSON:
0302504
0302504 PIN, Shift rod
20R69B, 20R70C, 20R71S, 20R72R, 20R73A, 25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 25E77S, 25E78C, 25E79R, 25R69B, 25R70C, 25R71S, 33E69A, 33E69A, 33E70M, 33E70M, 35E76G, 35E77C, 35E78R, 35E79A, 40E69R, 40E70A, 40E71B, 40E72E, 40E73D, 40E74S, 40E75C, 40
0303696
0303696 PIN, Swivel bracket to upper liner
10E74G, 10E75C, 10E76G, 10E77A, 15E74G, 15E75C, 15E76A, 15E77M, 20R69B, 20R70C, 20R71S, 20R72R, 20R73A, 25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 25E77S, 25E78C, 25R69B, 25R70C, 25R71S, 33E69A, 33E69A, 33E70M, 33E70M, 35E76G, 35E77C, 35E78R, 40E71B, 40
0302877
0302877 PIN, Gear and shaft groove
20R69B, 20R70C, 20R71S, 20R72R, 20R73A, 25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 25E77S, 25E78C, 25E79R, 25R69B, 25R70C, 25R71S, 35E76G, 35E77C, 35E78R, 35E79A, 6R69M, 6R70B, 6R71E, 6R72D, 6R73S, 6R74C, 6R75R, 6R76A, 6R77M, 6R78B, 6R79E, CD-25A, FD-22
0319127
0319127 PIN, Clevis to lock lever
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, J10ECCD, J10ECDB, J10ECES, J10ECOM, J10ECSE, J10ECUE, J10EEIR, J10EENA, J10EESC, J10ELCID, J10ELCNS, J10ELCRA, J10ELCTC, J15ECCS, J15ECDE, J15ECEC, J15EC
0319541
0319541 PIN,Bellcrank to shift rod
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 25E77S, 25E78C, 25E79R, 35E76G, 35E77C, 35E78R, 35E79A, J10ECDB, J10ECOM, J10ECSE, J10ECUE, J10ELCID, J10ELCNS, J10ELCRA, J10ELCTC, J15ECDE, J15ECIS, J15
0319055
0319055 PIN,Link to swivel brkt
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 25E77S, 35E76G, 35E77C, BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10FDLECM, BJ10FDLEDR, BJ10FDLEUA, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, B
0319692
0319692 PIN,Tilt lock
25E77S, 25E78C, 25E79R, 35E76G, 35E77C, 35E78R, 35E79A, BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC,
0320481