0338237 PIN, Throttle cable to lever JOHNSON
BJ10EEDD, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15RELEUC, HJ15KCF, HJ15KCLN, HJ15KCLO, J10EECC, J10EEOE, J10EERB, J10EETM, J10ELEER, J10ELSIM, J10ELSSA, J10RLSUR, J15EECR, J15EEOD, J15EERE, J15EETB, J15ELEEA, J15ELSI
PIN
Price: query
Rating:
Compatible models:
BJ10EEDD
BJ10RELEUS
BJ10RHLSDA
BJ10RHLSOR
BJ10RHLSRC
BJ10RHLSTS
BJ15EEDS
BJ15RELEUC
HJ15KCF
HJ15KCLN
HJ15KCLO
J10EECC
J10EEOE
J10EERB
J10EETM
J10ELEER
J10ELSIM
J10ELSSA
J10RLSUR
J15EECR
J15EEOD
J15EERE
J15EETB
J15ELEEA
J15ELSIB
J15ELSSM
J15RLSDR
J15RLSOC
J15RLSRS
J15RLSTD
J15RLSUA
J15WREES
J15WRLSIR
J15WRLSSC
SJ10REDD
SJ10RPB
SJ10RPLT
SJ10RPLY
JOHNSON
BRP JOHNSON entire parts catalog list:
- CYLINDER & CRANKCASE » 0338237
BJ10RHLSDA, BJ10RHSDA, J10RLSDC, J10RSDC 2006
BJ10RHLSOR, BJ10RHSOR, J10RLSOS, J10RSOS 2005
BJ10RHLSRC, BJ10RHSRC, J10RLSRD, J10RSRD 2004
BJ10RHLSTS, BJ10RHSTS, J10RLSTE, J10RSTE 2003
BJ15EEDS, BJ15ELEDS, BJ15REDS, BJ15RLEDS, J15EEDS, J15ELEDS, J15REDS, J15RELEDS, J15RLEDS, SJ15BAEDC, SJ15REDS, SJ15RLEDS 1996
BJ15RELEUC, J15EEUC, J15ELEUC, J15RELEUC, J15REUC, J15RLEUC, SJ15BAEUR 1997
HJ15KCF, HJ15KCLF, HJ15RPLW, HJ15RPW, SJ15RPLW, SJ15RPW 1997
HJ15KCLN, HJ15KCN, SJ15RPG, SJ15RPLG 1996
HJ15KCLO, HJ15KCO, SJ15RPC, SJ15RPLC 1998
J10EECC, J10ELECC, J10RECC, J10RELECC, J10RLECC, J10SELECC 1998
J10EEOE, J10ELEOE, J10RELEOE, J10REOE, J10RLEOE, J10SELEOE 1995
J10EERB, J10ELERB, J10RELERB, J10RERB, J10RLERB, J10SELERB 1994
J10EETM, J10ELETM, J10RELETM, J10RETM, J10RLETM, J10SELETM, TJ10RELETM 1993
J10ELEER, J10REER, J10RLEER, J10TEEER, J10TELEER 1999
J10ELSIM, J10EVLSIC, J10RGTSIC, J10RLGTSIC, J10RLSIM, J10RSIM, J10RVLSIC, J10RVSIC, J10TEGTSIC, J10TELSIM, J10TESIM, J10TVESIM 2001
J10ELSSA, J10EVLSSS, J10RGTSSS, J10RLGTSSS, J10RLSSA, J10RSSA, J10RVLSSS, J10RVSSS, J10TEGSSS, J10TELSSA, J10TESSA 2000
J10RLSUR, J10RSUR 2007
J15EECR, J15ELECR, J15RECR, J15RELECR, J15RLECR, SJ15BAECA 1998
J15EEOD, J15ELEOD, J15RELEOD, J15REOD, J15RLEOD 1995
J15EERE, J15ELERE, J15RELERE, J15RERE, J15RLERE 1994
J15EETB, J15ELETB, J15RELETB, J15RETB, J15RLETB 1993
J15ELEEA, J15REEA, J15RLEEA, J15TEEEA, J15TELEEA, SJ15BAEEM, SJ15RTEEM 1999
J15ELSIB, J15EVLSIC, J15RLSIB, J15RSIB, J15RVLSIC, J15RVSIC, J15TELSIB, J15TESIB, J15TVESIB, SJ15RTSIR 2001
J15ELSSM, J15EVLSSS, J15RLSSM, J15RSSM, J15RVLSSS, J15RVSSS, J15TELSSM, J15TESSM, SJ15RTSSB 2000
J15RLSDR, J15RSDR, J15RTSDC 2006
J15RLSOC, J15RSOC, J15RTSOS, J15WRLSOB, J15WRSOB 2005
J15RLSRS, J15RSRS, J15WRLSRM, J15WRSRM 2004
J15RLSTD, J15RSTD 2003
J15RLSUA, J15RSUA, J15RTSUR 2007
J15WREES, J15WRLEES 1999
J15WRLSIR, J15WRSIR 2001
J15WRLSSC, J15WRSSC 2000
SJ10REDD, SJ10RLEDD, SJ10SELEDD 1996
SJ10RPB, SJ10RPLB 1996
SJ10RPLT, SJ10RPT 1997
SJ10RPLY, SJ10RPY 1998
Information:
2. Loosen the clamps that hold hose (3) in place. Move hose (3) away from elbow (2). 3. Remove the bolts and retainers that hold tube (1) in place in elbow (2).4. Disconnect hose (4) from the elbow.5. Remove the bolts that hold elbow (2) to the water pump. Remove the elbow from the water pump and tube (1).6. Disconnect hose assembly (7) from the water pump.7. Remove bolts (6) that hold the water pump to the adapter.8. Fasten a hoist to water pump (5). Remove the bolts that hold the water pump to the front drive housing, and remove the water pump. The weight of the water pump is 37 kg (82 lb). The following steps are for installation of the water pump.9. Make sure the gasket for the adapter and the O-ring seal on the water pump are in position. Put clean engine oil on the O-ring seal.10. Fasten a hoist to water pump (5). Put the water pump in position on the engine, and install the bolts that hold it.11. Install bolts (6) to hold the adapter to the water pump.12. Connect hose assembly (7) to the water pump.13. Make sure the O-ring seals are in position on the end of tube (1) and in elbow (2). Put clean engine oil on the O-ring seals.14. Put elbow (2) in position on tube (1) and the water pump. Install the bolts that hold the elbow to the water pump.15. Install the retainers and bolts that hold tube (1) in position in the elbow.16. Put hose (3) in position on elbow (2), and tighten the clamps that hold it in place.17. Connect hose (4) to the water pump.18. Fill the cooling system with coolant to the correct level. See the Maintenance Manual.Disassemble Water Pump
Start By:a. remove water pump 1. Remove O-ring seal (4) from the back of housing assembly (3).2. Remove washer (1) that holds shaft assembly (2) in housing assembly (3).
Typical Example3. Remove cover (5) from housing assembly (3). Remove the O-ring seal from cover (5).
Typical Example4. Loosen nut (7) and the washer that hold impeller (6) to the pump shaft Use tooling (A) to loosen impeller (6) from the end of the pump shaft Remove tooling (A), nut (7), the washer and impeller (6) from the pump shaft and housing assembly (3).
Typical Example5. Remove spring (9) from seal assembly (8) and shaft assembly (2).6. Use a soft hammer, and push shaft assembly (2) out of seal assembly (8) and housing assembly (3). Remove seal assembly (8) from housing assembly (3). 7. Remove ceramic seal (10) from the rubber ring. Remove the rubber ring from housing assembly (3). 8. Remove seal (11) from the back of housing assembly (3).Assemble Water Pump
1. If necessary, make a replacement of the two filters in the pump housing at location (1).2. If necessary, make a replacement of plug (2) and the seal.
The cardboard sleeve is required to slightly stretch the inner diameter of the seal to prevent seal damage when installing the pump shaftRemove the cardboard sleeve only when ready to install the shaft
3. Use tool group (A) to install the seal in the housing assembly. Make sure the lip of the seal is toward the impeller. Put clean engine oil on the lip of the seal. 4. Install shaft assembly (3) in housing assembly (4). Install washer (5) and the bolts to hold shaft assembly (3) in position.
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Put ceramic seal (6) in position in the rubber ring. Use hand pressure and the tool (which is with the replacement seal) to install the ceramic seal.
Typical Example6. Remove the spring from seal assembly (7). Use hand pressure and the tool (which is with the replacement seal) to install the seal assembly. Push the seal assembly on the shaft until the seal faces make light contact.
Typical Example7. Install spring (8) on the carbon seal assembly.8. Put impeller (9) in position on the pump shaft as shown.
Typical Example9. Install washer (11) and nut (10). Tighten nut (10) to a torque of 200 25 N m (150 18 lbft). 10. Make sure the studs for cover (12) are tightened to a torque of 27 4 N m (20 3 lbft) in the pump housing.11. Put clean engine oil on O-ring seal (13), and install it on cover (12). Put cover (12) in position, and install the nuts to hold it to the pump housing.End By:a. install water pump
Start By:a. remove water pump 1. Remove O-ring seal (4) from the back of housing assembly (3).2. Remove washer (1) that holds shaft assembly (2) in housing assembly (3).
Typical Example3. Remove cover (5) from housing assembly (3). Remove the O-ring seal from cover (5).
Typical Example4. Loosen nut (7) and the washer that hold impeller (6) to the pump shaft Use tooling (A) to loosen impeller (6) from the end of the pump shaft Remove tooling (A), nut (7), the washer and impeller (6) from the pump shaft and housing assembly (3).
Typical Example5. Remove spring (9) from seal assembly (8) and shaft assembly (2).6. Use a soft hammer, and push shaft assembly (2) out of seal assembly (8) and housing assembly (3). Remove seal assembly (8) from housing assembly (3). 7. Remove ceramic seal (10) from the rubber ring. Remove the rubber ring from housing assembly (3). 8. Remove seal (11) from the back of housing assembly (3).Assemble Water Pump
1. If necessary, make a replacement of the two filters in the pump housing at location (1).2. If necessary, make a replacement of plug (2) and the seal.
The cardboard sleeve is required to slightly stretch the inner diameter of the seal to prevent seal damage when installing the pump shaftRemove the cardboard sleeve only when ready to install the shaft
3. Use tool group (A) to install the seal in the housing assembly. Make sure the lip of the seal is toward the impeller. Put clean engine oil on the lip of the seal. 4. Install shaft assembly (3) in housing assembly (4). Install washer (5) and the bolts to hold shaft assembly (3) in position.
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
5. Put ceramic seal (6) in position in the rubber ring. Use hand pressure and the tool (which is with the replacement seal) to install the ceramic seal.
Typical Example6. Remove the spring from seal assembly (7). Use hand pressure and the tool (which is with the replacement seal) to install the seal assembly. Push the seal assembly on the shaft until the seal faces make light contact.
Typical Example7. Install spring (8) on the carbon seal assembly.8. Put impeller (9) in position on the pump shaft as shown.
Typical Example9. Install washer (11) and nut (10). Tighten nut (10) to a torque of 200 25 N m (150 18 lbft). 10. Make sure the studs for cover (12) are tightened to a torque of 27 4 N m (20 3 lbft) in the pump housing.11. Put clean engine oil on O-ring seal (13), and install it on cover (12). Put cover (12) in position, and install the nuts to hold it to the pump housing.End By:a. install water pump
Parts pin JOHNSON:
0305821
0305821 PIN, Indicator
100ESL71A, 100ESL72R, 100ML79S, 10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78
0308081
0308081 PIN, Guide
100ESL71A, 100ESL72R, 100ML79S, 10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 115EL77S, 115ESL69E, 115ESL70D, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 125ESL71C, 125ESL72R, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78
0308376
0308376 PIN, Pivot, shift lever
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 20R69B, 20R70C, 20R71S, 20R72R, 20R73A, 25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 25E77S, 25E78C, 25E79R, 25R69B, 25R70C, 25R71S, 33E69A, 33E69A, 33E70M, 3
0302504
0302504 PIN, Shift rod
20R69B, 20R70C, 20R71S, 20R72R, 20R73A, 25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 25E77S, 25E78C, 25E79R, 25R69B, 25R70C, 25R71S, 33E69A, 33E69A, 33E70M, 33E70M, 35E76G, 35E77C, 35E78R, 35E79A, 40E69R, 40E70A, 40E71B, 40E72E, 40E73D, 40E74S, 40E75C, 40
0511469
0511469 PIN
100ML79S, 10E77A, 10E78M, 10EL79B, 115ETZ78C, 115ML79R, 140ML78C, 140ML79R, 150TL79C, 15E77M, 15E78B, 15E79E, 175TL79R, 200TL79A, 235TL70A, 25E77S, 25E78C, 25E79R, 35E77C, 35E78R, 35E79A, 4R77B, 4R78E, 4R79D, 50R79C, 55E78S, 55E79C, 6R77M, 6R78B, 6R7
0336532
0447011
0345942
0345942 PIN, Support bracket
BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, J10ELEER, J10ELSIM, J10ELSSA, J10RLSUR, J15ELEEA, J15ELSIB, J15ELSSM, J15RLSDR, J15RLSOC, J15RLSRS, J15RLSTD, J15RLSUA, J15WREES, J15WRLSIR, J15WRLSSC