0122492 PISTON ROD JOHNSON
115EL77S, 115ESL74B, 115ESL75E, 135ESL74B, 135ESL75E, 85EL76D, 85EL77S, J35AELCDE, J35AELCUD, J40AELCCS, J40ECDE, J40ECUD, J45RCE, J50BECCS, J50BECDE, J50BECIC, J50BECNR, J50BECOB, J50BECRM, J50BECTA, J50BECUD, J55RCIM, J55RWLE, J60ECIA, J60ECNM, J60
PISTON
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- POWER TILT AND TRIM » 0122492
115ESL75E, 115ETL75E 1975
135ESL74B, 135ETL74B 1974
135ESL75E, 135ETL75E 1975
85EL76D, 85EL76G, 85ETLR76D, 85ETLR76G 1976
85EL77S, 85ETLR77S 1977
J35AELCDE, J35ARLCDE 1986
J35AELCUD, J35ARLCUD 1987
J40AELCCS, J40ARLCCS, J40ATLCCS, J40ECCS, J40ELCCS, J40RCCS, J40RLCCS, J40TECCS, J40TELCCS, J40TLCCS, J40TTLCCS 1988
J40ECDE, J40ELCDE, J40RCDE, J40RLCDE, J40TECDE, J40TELCDE, J40TLCDE 1986
J40ECUD, J40ELCUD, J40RCUD, J40RLCUD, J40TECUD, J40TLCUD 1987
J45RCE, J45RCLE, J45WMLE 1989
J50BECCS, J50BELCCS, J50TELCCS, J50TLCCS 1988
J50BECDE, J50BELCDE, J50TELCDE, J50TLCDE 1986
J50BECIC, J50BELCIC 1981
J50BECNR, J50BELCNR 1982
J50BECOB, J50BELCOB, J50TELCOB, J50TLCOB 1985
J50BECRM, J50BELCRM, J50TELCRM, J50TLCRM 1984
J50BECTA, J50BELCTA, J50TELCTA 1983
J50BECUD, J50BELCUD, J50TELCUD, J50TLCUD 1987
J55RCIM, J55RLCIM 1981
J55RWLE 1989
J60ECIA, J60ECIH, J60ELCIA, J60ELCIH, J60TLCIA, J60TLCIH 1981
J60ECNM, J60ELCNM, J60TLCNM 1982
J60ECTB, J60ELCTB, J60TLCTB 1983
J60ELCOD, J60TLCOD 1985
J60ELCRE, J60TLCRE 1984
Information:
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6080 Torque Multiplier Gp 1
5P-1748 Socket 1
4C-9451 Rear Idler Gear Wrench 1
4C-9452 Rear Idler Gear Wrench 1
B 9U-5932(1) Torque Wrench Extension 1
1P-2382(2) Wrench Adapter 1
C 4C-5593 Anti-Seize Compound -
(1) This tool is used on later models.
(2) This tool is used on earlier models.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00636750
Earlier
Illustration 2 g00610687
Later
Illustration 3 g01303614
Earlier
Illustration 4 g00610685
Later
Note: The rear housing was removed for illustrative purposes only.
If the bearing was removed from gear (26), install the bearing in the gear. The bearing must be 3.0 0.5 mm (0.12 0.02 inch) below the surface of the side of the gear that has the smaller shoulder.
Place gear (17) in position on other gear (26). Install the bolts.
Attach a suitable lifting device to gear (17). The weight of gear (17) and other gear (26) is approximately 55 kg (121 lb).
Place the following components in position on shaft (24): gear (17), other gear (26) and retainer (21). Install bolts (18). Do not tighten the bolts at this time.
Attach a suitable lifting device to gear (17). The weight of the gear assembly is approximately 85 kg (187 lb). Place gear (17) and shaft (24) in position in the rear housing through the camshaft drive gear opening.
Attach a suitable lifting device to gear (17) through the opening for the accessory drive in the rear housing. Disconnect the suitable lifting device from gear (17) through the camshaft drive gear opening.
Align the teeth on gear (17) with the teeth on the crankshaft gear. Place shaft (24) in position on the cylinder block. Install bolts (25). Refer to Specifications, "Gear Group (Rear)" for the correct torque.
Tighten bolts (18).
If the bearings were removed from gears (22), install the bearings in the gears. The bearings must be 3.0 0.5 mm (0.12 0.02 inch) below the flat surface of the gear. The inside diameter of the bearings should be 150.002 0.020 mm (5.9056 0.0008 inch) after installation.
Place gear (22) and retainer (23) in position on shaft (19). Install the bolts that hold these components in place.
Attach a suitable lifting device to gear (22). The weight of the shaft and gear (22) is approximately 41 kg (90 lb). Place the shaft and gear (22) in position on the cylinder block through the camshaft drive gear opening in the rear housing. Install bolts (20). Refer to Specifications, "Gear Group (Rear)" for the correct torque.
Repeat Step 10 and Step 11 for the other idler gear.
Illustration 5 g00610680
Attach a suitable lifting device to drive shaft (1). The weight of drive shaft (1) is approximately 40 kg (88 lb). Place spacer (16) in position on the end of drive shaft (1). This is done on earlier engines only.
Install drive shaft (1) and spacer (16). Align the dowel in drive shaft (1) with the dowel hole in camshaft segment (3). Install bolts (2). Tighten all of bolts (2) by hand.
Illustration 6 g00610676
Place plate (15) in position and install bolts (14).
Place plate (12) in position on drive shaft (1) and install bolts (13).
Illustration 7 g00610662
Be sure that camshaft timing pins (6) are installed in both camshafts.
Parts piston JOHNSON:
0317859
0317859 PISTON,Shift assy.
115ESL73M, 115ESL74B, 135ESL73M, 135ESL74B, 50ES73R, 50ES74M, 65ES73R, 70ES74M, 70ES75B, 85ESL73M, 85ESL74B
0386330
0386300
0386329
0388315
0388315 PISTON, .030 O.S., 85 HP
115EL77S, 115ETZ78C, 115TXL77S, 140ML77S, 140ML78C, 85EL77S, 85ETLR78C, 85TXLR77S
0388673
0388673 PISTON,.030,115 HP
100ML79S, 115EL77S, 115ETZ78C, 115ML79R, 115TXL77S, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 175TL77S, 175TL78C, 200TL77C, 200TL78R, 235TL78R, 85EL77S, 85ETLR78C, 85ML79R, 85TXLR77S
0388312
0388312 PISTON,Std.,85 HP
115EL77S, 115ETZ78C, 115TXL77S, 140ML77S, 140ML78C, 85EL77S, 85ETLR78C, 85TXLR77S
0391798
0391798 PISTON ASSY.,Std.
J35AELCDE, J35AELCUD, J40AELCCS, J40ECDE, J40ECEC, J40ECOB, J40ECRM, J40ECUD, J40EEIA, J40EENJ, J40EERE, J40EESR, J40EETB, J45RCCDS, J45RCCUC, J45RCE, J45RCEIA, J45RCENM, J45RCESR, J45RCETB, J48ESLCCC, J48ESLCCC, J48ESLCER, J48ESLCER, J48ESLCUS, J48E