5032162 JOHNSON PISTON (O.S.:0.25mm)


5032162 PISTON (O.S.:0.25mm) JOHNSON J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA PISTON
5032162 PISTON (O.S.:0.25mm) JOHNSON
Rating:
103

Buy PISTON (O.S.:0.25mm) 5032162 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 12
 

BRP JOHNSON entire parts catalog list:

J25PL4SOC, J25TEL4SOC 2005
J25PL4SRS 2004
J30PL4SDR 2006
J30PL4SOC, J30TEL4SOC 2005
J30PL4SRS 2004
J30PL4SUA 2007
J30TEL4SDR 2006
J30TEL4SUA 2007

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Prior to removal of the flywheel, position the number one piston in the top center position (TC). The engine should be at the top center position in order to properly install the rear gear group. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Illustration 1 g02087895
(X) Marker
(Y) Alignment Mark
With the number one piston in the top center position (TC), attach a Marker to the engine and place an Alignment Mark on the vibration damper.
Remove the flywheel housing.
Illustration 2 g01151801
Remove bolts (10), thrust plate (11), and gear assembly (9).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (9).
Remove bolts (8), gear assembly (6), and shaft assembly (7).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (6).
Remove bolts (2), gear assembly (1), and shaft assembly (3).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (1).
Remove gear assembly (12).
Remove bolts (5) and gear assemblies (4).
Illustration 3 g01151842
Remove bolts (16) and shaft assembly (17).
Remove bolts (13), thrust plates (14), and adapter assemblies (15).
Use bolt (13) in order to remove the sealing plates. Remove the O-ring seals. C32 Removal Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1P-0520 Driver Group 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Prior to removal of the flywheel, position the number one piston in the top center position (TC). The engine should be at the top center position in order to properly install the rear gear group. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Illustration 4 g02087895
(X) Marker
(Y) Alignment Mark
With the number one piston in the top center position (TC), attach a Marker to the engine and place an Alignment Mark on the vibration damper.
Remove the flywheel housing.
Illustration 5 g03427967
Remove bolts (10), retainer assembly (11), the O-ring seal, and gear assembly (9).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (9).
Remove bolts (8), gear assembly (6), and stub shaft assembly (7).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (6).
Remove bolts (2), gear assembly (1), and stub shaft assembly (3).
Use Tooling (A) and a suitable press to remove the bearing from gear assembly (1).
Remove gear assembly (12).
Remove bolts (5) and gear assemblies (4).
Remove gear assembly (13) and the thrust washers.


Parts piston JOHNSON:

5031930
PISTON
5031930 PISTON
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
5032163
 
5032163 PISTON (O.S.:0.50mm)
J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA
Back to top