0318583 JOHNSON PIVOT PIN,Shift rod lever

Illustration 1 g00538209
Typical exampleAir inlet and exhaust system components (1) Cylinder head (2) Air inlet (3) Turbocharger compressor wheel (4) Inlet valves (5) Exhaust valves (6) Turbocharger turbine wheel (7) Exhaust outlet (8) Inlet manifold (9) Exhaust manifoldThe components of the air inlet and exhaust system control the quality of air and the amount of air that is available for combustion. The air inlet and exhaust system consists of the following components:
Air cleaner
Turbocharger
Cylinder head
Valves and valve system components
Piston and cylinder
Exhaust manifold Inlet air is pulled through the air cleaner into air inlet (2) by turbocharger compressor wheel (3). The air is compressed and heated to about 150 °C (300 °F).Air is forced into inlet manifold (8). Air flow from the inlet chambers into the cylinders is controlled by inlet valves (4). There are two inlet valves and two exhaust valves (5) for each cylinder. The inlet valves open when the piston moves down on the inlet stroke. When the inlet valves open, cooled compressed air from the inlet port is pulled into the cylinder. The inlet valves close and the piston begins to move up on the compression stroke. The air in the cylinder is compressed. When the piston is near the top of the compression stroke, fuel is injected into the cylinder. The fuel mixes with the air and combustion starts. During the power stroke, the combustion force pushes the piston downward. The exhaust valves open and the exhaust gases are pushed through the exhaust port into exhaust manifold (9) as the piston rises on the exhaust stroke. After the exhaust stroke, the exhaust valves close and the cycle starts again. The complete cycle consists of four strokes:
Inlet
Compression
Power
ExhaustExhaust gases from exhaust manifold (9) enter the turbine side of the turbocharger in order to turn turbocharger turbine wheel (6). The turbine wheel is connected to the shaft that drives the compressor wheel. Exhaust gases from the turbocharger pass through exhaust outlet (7), a muffler and an exhaust stack.Turbocharger
Illustration 2 g00294193
Typical exampleTurbocharger (1) Air inlet (2) Compressor housing (3) Compressor wheel (4) Bearing (5) Oil inlet port (6) Bearing (7) Turbine housing (8) Turbine wheel (9) Exhaust outlet (10) Oil outlet port (11) Exhaust inletThe turbocharger is installed on the center section of the exhaust manifold. All the exhaust gases from the engine go through the turbocharger.The exhaust gases enter turbine housing (7) through exhaust inlet (11). The exhaust gases then push the blades of turbine wheel (8). The turbine wheel is connected by a shaft to compressor wheel (3) .Clean air from the air cleaners is pulled through compressor housing air inlet (1) by the rotation of compressor wheel (3). The action of the compressor wheel blades causes a compression of the inlet air. This compression gives the engine more power by allowing the engine to burn more air and more fuel during combustion.When the load on the engine increases, more fuel is injected into the cylinders. The combustion of this additional fuel produces more exhaust gases. The additional exhaust gases cause the turbine and the compressor wheels of the turbocharger to turn faster. As the compressor wheel turns faster, more air is forced into the cylinders. The increased flow of air gives the engine more power by allowing the engine to burn the additional fuel with greater efficiency.Bearings (4) and (6) for the turbocharger use engine oil under pressure for lubrication. The oil comes in through oil inlet port (5). The oil then goes through passages in the center section in order to lubricate the bearings. Oil from the turbocharger goes out through oil outlet port (10) in the bottom of the center section. The oil then goes back to the engine lubrication system. Valve System Components
Illustration 3 g00411726
Valve system components (1) Valve bridge (2) Valve rotator (3) Rocker arm (4) Pushrod (5) Valve springs (6) Valves (7) Valve guide (8) Camshaft (9) LifterThe valve system components control the flow of inlet air into the cylinders during engine operation. The valve system components also control the flow of exhaust gases out of the cylinders during engine operation.The crankshaft gear drives the camshaft gear through an idler gear. Camshaft (8) must be timed to the crankshaft in order to get the correct relation between the piston movement and the valve movement.The camshaft has three camshaft lobes for each cylinder. Two lobes operate the inlet and exhaust valves, and one operates the unit injector mechanism. As the camshaft turns, the camshaft lobes cause lifter (9) to move pushrod (4) up and down. Upward movement of the pushrod against rocker arm (3) results in downward movement (opening) of valves (6) .Each cylinder has two inlet valves and two exhaust valves. Valve springs (5) close the valves when the lifters move down. Valve rotators (2) cause the valves to rotate while the engine is running. The rotation of the valves keeps the carbon deposits on the valves to a minimum. Also, the rotation gives the valves longer service life.