0203132 JOHNSON PLATE,Pump


0203132 PLATE,Pump JOHNSON 4R69B, 4R70E, 4R71D, 4R72S, 4R73C, 4R74R, 4R75A, 4R76M, 4R77B, 4R78E, 4R79D, J4RLCSS, J4WCIC, J4WCNR, JH-23A, LD-13B PLATE
0203132 PLATE,Pump JOHNSON
Rating:
53

Buy PLATE,Pump 0203132 JOHNSON genuine, new aftermarket parts with delivery

You can buy parts:

As an associate, we earn commssions on qualifying purchases through the links below
$99.99
 

10-10-2023
12.0[5.40] Pounds
-: -
PantsSaver Custom Fits Car Floor Mats for AUDI A4 ALLROAD 2013, Front & 2nd Seat Heavy Duty Floor Mat (4PC), All Weather Protection for Vehicle, Gray
Custom designed to fit your AUDI A4 ALLROAD 2013 , Install in seconds, no cutting or tools required || Features a patented Pants Saver central pan that holds and traps up to 500ml (16-Ounce) of water and keeps you and your vehicle's interior clean and dry || Lifetime warranty against cracking or breaking || Superior All weather performance, Made from non-toxic, weather-resistant recycled PVC, BPA-free PantsSaver xact fit floor mats are waterproof and odorless even in extreme weather and maintain flexibility and durability down to minus 76°F (-60°C) || Manufacturer-Lifetime Warranty: Box Contains 4Pcs x Car Mats.
Number on catalog scheme: 4
 

BRP JOHNSON entire parts catalog list:

4R69B, 4W69B, 4WF69B 1969
4R70E, 4RL70E, 4W70E, 4WL70E 1970
4R71D, 4RL71D, 4W71D, 4WL71D 1971
4R72S, 4W72S 1972
4R73C, 4W73C 1973
4R74R, 4W74R 1974
4R75A, 4W75A 1975
4R76M, 4W76M 1976
4R77B, 4W77B 1977
4R78E, 4RL78E, 4W78E 1978
4R79D, 4RL79D, 4W79D 1979
J4RLCSS, J4WCSS 1980
J4WCIC 1981
J4WCNR 1982
JH-23A, JH-23M, JHF-23A, JHF-23M, JHFL-23A, JHFL-23M, JHL-23A, JHL-23M, JW-23A, JW-23M, JWF-23A, JWF-23M, JWFL-23A, JWFL-23M, JWL-23A, JWL-23M 1968
LD-13B, LD-13E, LD-13M, LDL-13B, LDL-13E, LDL-13M 1968

Information:

Probable Causes
Diagnostic codes
ECM parameters
Air intake and exhaust system
Fuel supply
Individual malfunctioning cylinders
Electronic unit injectorsRecommended Actions
Diagnostic Codes
Check for active diagnostic codes on the electronic service tool. Troubleshoot any active codes before continuing with this procedure.ECM Parameters
Ensure that the problem is not a programmed parameter.
Ensure that the correct mode was selected by using the electronic service tool.
Use the electronic service tool to verify the correct engine rating for the engine.
Use the electronic service tool to verify the maximum engine speed limit.
Use the electronic service tool to verify the following parameters at maximum speed: the boost pressure, the smoke limit, the torque limit and the amount of fuel that is delivered.
Use the electronic service tool to reset the parameters to the OEM specifications.
Ensure that the repairs have eliminated the performance problems.
If the repairs have not eliminated the faults proceed to "Air Intake and Exhaust System". Air Intake and Exhaust System
Check the air filter restriction indicator, if equipped.
Ensure that the air filter is clean and serviceable.
Check the air intake and the exhaust system for the following defects:
Blockages
Restrictions
Damage to the air intake and exhaust lines and hoses
Make all necessary repairs to the engine.
Ensure that the repairs have eliminated the fault.
If the fault has not been eliminated, proceed to "Fuel Supply". Fuel Supply
Visually check the fuel tank for fuel. The fuel gauge may be faulty.
Ensure that the fuel supply valve is in the full OPEN position.
If the temperature is below 0 °C (32 °F), check for solidified fuel (wax).
Visually inspect the fuel supply lines for restrictions.
Check that the low pressure fuel lines are tight and secured properly.
Remove the fuel filters. Inspect the fuel filters for contamination. Install new fuel filters. Refer to the Operation and Maintenance Manual, "Fuel System Filter- Replace and Fuel System Primary Filter (Water Separator) Element - Replace". Determine the cause of the contamination.
Check the diesel fuel for contamination. Refer to Systems Operation, Testing and Adjusting, "Fuel Quality - Test".
Check for air in the low pressure fuel system. Refer to Systems Operation, Testing and Adjusting, "Air in Fuel - Test".
Ensure that the fuel system has been primed. Refer to Testing and Adjusting, "Fuel System - Prime".
Check the fuel pressure. Refer to Testing and Adjusting, "Fuel System Pressure - Test".
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Contact with high pressure fuel may cause personal injury or death. Wait 60 seconds after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines.
If the high pressure fuel lines have a leak, the high pressure fuel lines must be replaced. Refer to Disassembly and Assembly, "Fuel injection lines - Remove and Fuel injection lines - Install".
If the repairs do not eliminate the fault proceed to "Individual Malfunctioning Cylinders". Individual Malfunctioning Cylinders
With the engine speed at a fast idle, use the electronic service tool to isolate one cylinder at a time. Note if there is any reduction in engine speed. If a reduction in engine speed is not noted, the isolated cylinder is not operating under normal conditions. If the isolation of a particular cylinder results in a reduction of engine speed that is less than normal, this may indicate that the cylinder is operating below normal performance. Investigate the cause of the fault on any cylinder that is not operating. Investigate the cause of the fault on any cylinder that is operating below normal performance.
If all cylinders have been checked and no faults were detected proceed to "Electronic Unit Injectors". Electronic Unit Injectors
With the engine speed at a fast idle, use the electronic service tool to isolate one cylinder at a time. Note if there is any reduction in engine speed. If a reduction in engine speed is not noted, the isolated electronic unit injector is not operating under normal conditions. If the isolation of a particular cylinder results in a reduction of engine speed that is less than normal, this may indicate that the electronic unit injector is operating below normal performance.
Remove the electronic unit injector from the suspect cylinder. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Install a new electronic unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
Repeat the test in 1. If the fault is still apparent, remove the replacement electronic unit injector and install the original electronic unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" and Disassembly and Assembly, "Electronic Unit Injector - Install".


Parts plate JOHNSON:

0307561
 
0307561 PLATE,Swivel
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 1R69C, 1R70R, 20R69B, 20R70C, 20R71S, 20R72R, 20R73A, 25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 25E77S, 25E78C, 25E79R, 25R69B, 25R70C, 25R71S, 2R71A, 2R72
0203172
 
0203172 PLATE,Exhaust cover
4R69B, 4R70E, 4R71D, 4R72S, 4R73C, 4R74R, 4R75A, 4R76M, 4R77B, JH-23A
0203174
0316371
 
0316371 PLATE, Pulley
2R71A, 2R72M, 2R73B, 2R74E, 2R75D, 2R76S, 2R77C, 2R78R, 2R79A, 4R79D, J2RCSM, J4RLCSS
0323485
 
0323485 PLATE, Leaf back-up
4R78E, 4R79D, BJ3REDS, BJ4BREDS, BJ4BREUC, BJ4RDHEDS, J3BRCEC, J3BRESR, J3RCCM, J3RCUA, J3REIA, J3RENM, J3REOD, J3RERE, J3RETB, J3REUC, J4BRCIC, J4BRECRJ, J4BRHCCS, J4BRHCDE, J4BRHCNR, J4BRHCOB, J4BRHCRM, J4BRHCTA, J4BRHCUD, J4RCCS, J4RCEC, J4RCUD, J
0581854
 
0581854 PLATE AND SLEEVE ASSY
10E78M, 15E78B, 25E78C, 35E78R, 4R78E, 55E78S, 6R78B
0582052
Back to top