0212769 JOHNSON PLATE, Applique


0212769 PLATE, Applique JOHNSON BJ40EEDS, BJ40EEUC, BJ50BEEDS, BJ50RLEUC, J40EEOD, J50BEEOD PLATE
0212769 PLATE, Applique JOHNSON
Rating:
78

Buy PLATE, Applique 0212769 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

BRP JOHNSON entire parts catalog list:

BJ40EEDS, BJ40ELEDS, BJ40TLEDS, HJ40REDS, HJ40RLEDS, J40ELEDS, J40REDS, J40RLEDS, J40TEEDS, J40TELEDS, J40TLEDS, J40TTLEDS, SJ40EEDS, SJ40REDS, SJ40RLEDS 1996
BJ40EEUC, BJ40ELEUC, BJ40TLEUC, HJ40REUC, HJ40RLEUC, J40ELEUC, J40REUC, J40RLEUC, J40TEEUC, J40TELEUC, J40TLEUC, J40TTLEUC 1997
BJ50BEEDS, BJ50BELEDS, BJ50TLEDS, J50JEDS, J50TLEDS 1996
BJ50RLEUC, BJ50TLEUC, BJ50TSLEUS, J50ESLEUR, J50JEUC, J50TLEUC, J50TSLEUS 1997
J40EEOD, J40ELEOD, J40REOD, J40RLEOD, J40TEEOD, J40TELEOD, J40TLEOD, J40TTLEOD 1995
J50BEEOD, J50BELEOD, J50JEOD, J50TELEOD, J50TLEOD 1995

Information:


Illustration 1 g00671263
SchematicTest Step 1. Check for Connector Damage.
Turn the circuit breaker for the battery to the OFF position.
Turn the keyswitch to the OFF/RESET position.
Thoroughly inspect ECM connector J1/P1, ECM connector J2/P2, machine connector J3/P3, and power shift solenoid connector J113/P113. Refer to Troubleshooting, "Inspecting Electrical Connectors" for details.
Perform a 45 N (10 lb) pull test on each of the wires in the ECM connector that are associated with the circuit.
Check the ECM connector (allen head screw) for the proper torque of 6.0 N m (55 lb in).
Check the customer connector (allen head screw) for the proper torque of 2.25 0.25 N m (20 2 lb in).
Check the harness and the wiring for abrasion and pinch points.Expected Result:All connectors, pins, and sockets should be completely inserted and coupled. The harness and wiring should be free of corrosion, abrasion, and pinch points. All connections and grounds should be tight and free of corrosion.Results:
OK - All connectors, pins, and sockets are completely inserted and coupled. The harness and wiring are free of corrosion, abrasion, and pinch points. All connections and grounds are tight and free of corrosion. Proceed to Test Step 2.
Not OK - Repair: Repair the connectors or wiring and/or replace the connectors or wiring. Ensure that all of the seals are properly in place and that the connectors are completely coupled.Verify that the repair eliminates the problem. Stop.Test Step 2. Check the Solenoid for an Internal Short or Open.
Disconnect power shift solenoid connector J113/P113.
Measure the resistance between P113-1 and P113-2.Expected Result:The resistance should be between 7 Ohms and 17 Ohms.Results:
OK - The resistance is between 7 Ohms and 17 Ohms. Proceed to Test Step 3.
Not OK - The resistance is not between 7 Ohms and 17 Ohms. The solenoid is faulty.Repair: Replace the solenoid.Verify that the repair eliminates the problem. Stop.Test Step 3. Check the Resistance through the Harness.
Disconnect ECM connector J2/P2.
Use a suitable piece of wire to short P2-13 (Power Shift Solenoid) to P2-7 (Solenoid Return).
Measure the resistance between J113-1 and J113-2.
Remove the wire short.Expected Result:The resistance should be less than 10 Ohms.Results:
OK - The resistance is less than 10 Ohms. Proceed to Test Step 4.
Not OK - The resistance is greater than 10 Ohms. There is an open circuit or there is excessive resistance in the harness.Repair: Repair the circuit.Verify that the repair eliminates the problem. Stop.Test Step 4. Check for Shorts in the Harness.
Turn the keyswitch to the OFF/RESET position.
Disconnect ECM connector J2/P2 and power shift solenoid connector J113/P113.
Measure the resistance between engine ground and each terminal of power shift solenoid connector J113.
Measure the resistance between both terminals of power shift solenoid connector J113.Expected Result:The resistance should be greater than 20,000 Ohms for each reading.Results:
OK - The resistance is greater than 20,000 Ohms for each reading. Proceed to Test Step 5.
Not OK - The resistance is less than 20,000 Ohms for each reading. There is a short in the harness between the ECM and the power shift solenoid.Repair: Repair the circuit.Verify that the repair eliminates the problem. Stop.Test Step 5. Check the Voltage for the Solenoid at the ECM.
Reconnect all connectors.
Connect ET to the service tool connector.
Start the engine.
Ensure that the keyswitch is in the ON position.
Check for any Active Diagnostic Codes.Expected Result:The following diagnostics should not be active:
581-05 "Power Shift Solenoid open circuit"
581-06 "Power Shift Solenoid short to ground"Results:
OK - The solenoid and the harness are OK.Repair: If the system does not function properly refer to Troubleshooting, "Unstable Hydraulic Function". Stop.
Not OK - The ECM is faulty.Repair: Replace the ECM. Refer to Troubleshooting, "Replacing the ECM".Verify that the repair eliminates the problem. Stop.


Parts plate JOHNSON:

0327944
PLATE,Throttle control
0327944 PLATE,Throttle control
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15RELEUC, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25ARECA, BJ25AREDC, BJ25AREUR, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25PL3EEM, BJ25PL3SIE, BJ25PL3SSB, B
0340268
 
0340268 PLATE, Rear
BJ40EEDS, BJ50BEEDS, J40EEOD, J40EERE, J50BEEOD, J50BEERE
0340269
 
0340269 PLATE, Applique
BJ40EEDS, BJ50BEEDS, J40EEOD, J40EERE, J50BEEOD, J50BEERE
0211943
 
0211943 PLATE, Rear
J40EEOD, J50BEEOD
0212770
 
0212770 PLATE, Rear
BJ40EEDS, BJ50BEEDS, J40EEOD, J50BEEOD
0341140
 
0341140 PLATE, Front
BJ40EEDS, BJ50BEEDS, J40EEOD, J50BEEOD
0212895
 
0212895 PLATE, Front
BJ40EEUC, BJ50RLEUC
0343206
 
0343206 PLATE, Rear
BJ40EECR, BJ40EEUC, BJ50ESECC, BJ50RLEUC
Back to top