0212771 JOHNSON PLATE, Front


0212771 PLATE, Front JOHNSON BJ40EEDS, BJ40EEUC, BJ50BEEDS, BJ50RLEUC, J40EEOD, J50BEEOD PLATE

Buy PLATE, Front 0212771 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 20
 

BRP JOHNSON entire parts catalog list:

BJ40EEDS, BJ40ELEDS, BJ40TLEDS, HJ40REDS, HJ40RLEDS, J40ELEDS, J40REDS, J40RLEDS, J40TEEDS, J40TELEDS, J40TLEDS, J40TTLEDS, SJ40EEDS, SJ40REDS, SJ40RLEDS 1996
BJ40EEUC, BJ40ELEUC, BJ40TLEUC, HJ40REUC, HJ40RLEUC, J40ELEUC, J40REUC, J40RLEUC, J40TEEUC, J40TELEUC, J40TLEUC, J40TTLEUC 1997
BJ50BEEDS, BJ50BELEDS, BJ50TLEDS, J50JEDS, J50TLEDS 1996
BJ50RLEUC, BJ50TLEUC, BJ50TSLEUS, J50ESLEUR, J50JEUC, J50TLEUC, J50TSLEUS 1997
J40EEOD, J40ELEOD, J40REOD, J40RLEOD, J40TEEOD, J40TELEOD, J40TLEOD, J40TTLEOD 1995
J50BEEOD, J50BELEOD, J50JEOD, J50TELEOD, J50TLEOD 1995

Information:


Typical1. Remove the bolts that hold clips (3) in position.2. Remove bolt (2) and the washer. Pull tube assembly (1) and the O-ring seal out of the oil pump.
Typical3. Remove bolt and nut (5). Remove the bolts that hold tube assemblies (4) and (6) in position and remove the tube assemblies as a unit.
Typical4. Remove three bolts (7) and washers to remove oil pump (8) from the engine. The following steps are for the installation of the oil pump.5. Put oil pump (8) in position on the engine and install the three bolts and washers to hold it. Make sure the O-ring seals are installed on the ends of all tube assemblies before they are installed. Put clean engine oil on the O-ring seals at assembly.6. Install tube assembly (6) in tube assembly (4). Put the tube assemblies in position as a unit and install the bolts to hold them.7. Install bolt and nut (5) to hold the clip to the support.8. Install tube assembly (1) and the bolt and washer to hold it in the oil pump. Install the bolts and washers to hold the clips for tube assembly (1) in position.End By:a. install oil panDisassemble & Assemble Oil Pump
Start By:a. remove oil pump 1. Remove the bolt and pull pipe assembly (1) out of the pump body. 2. Remove O-ring seal (2) from pipe assembly (1).3. Remove clip (4) and screen assembly (3) from the bell assembly. 4. Remove the bolts and washers to remove brackets (5), (6) and bell assembly (7) from pipe assembly (1). 5. Remove bolt (9), thrust plate (8) and idler gear (10) from the shaft assembly. 6. Use Tool group (A) and a press to remove the bearing from idler gear (10). 7. Remove the bolts and shaft assembly (12) from the pump body.8. Remove the bolt and washer (11) that hold the pump drive gear. 9. Use Tooling (A) and (B) to remove drive gear (13) from the pump. Remove the key from the pump shaft. 10. Remove the bolts and body (15) from the spacer and body (14). 11. If necessary, use a press and Tool group (A) to push bearings (16) from body (15). 12. Remove gears (18) from the shaft assemblies.13. Remove spacer (17) from body (14). 14. If necessary, remove bearings (19) from spacer (17). 15. Remove shaft assemblies (20) and (21) from body (14). 16. Remove retainer (22), spacer (25), spring (24) and plunger (23) from body (14). 17. If necessary, use Tool group (A) and a press to push bearings (26) out of body (14). The following steps are for the assembly of the oil pump.18. Make sure all of the parts are clean and free of dirt and foreign material. Put clean engine oil on the parts at assembly. 19. Use Tool group (A) to install bearings (26) until they are even with the outside surface of main pump body (14). Install bearings (26) so the junctions in the bearings are 30 15 degreesfrom the center line of the bearing bores and toward the oil pump outlet passage as shown.20. Install plunger (23), spring (24), spacer (25), retainer (22) and the bolts in body (14) as shown.21. Install shaft assemblies (20) and (21) in body (14).22. Use Tool group (A) to install bearings (19) in spacer (17). Install the bearings in the center of their bores. Make sure the oil holes in the bearings are in alignment with the oil holes in the spacer and the junctions in the bearings in alignment with the cavity in the spacer.23. Install spacer (17) over the shaft assemblies on body (14).24. Install gears (18) on the shaft assemblies. 25. Use Tool group (A) to install bearings (16) in pump body (15) until they are 1.52 0.25 mm (.060 .010 in.)from the inside edge of the bearing bores. Install the bearings so the junctions in the bearing are 30 15 degreesfrom the center line of the bearing bores, and toward the outlet passage. The outlet passage has a cavity between the bearing bores.26. Put body (15) in position over the shaft assemblies on the spacer and body (14). Install the bolts to hold the pump together.27. Install the key and drive gear (13) on the shaft assembly.28. Install washer (11) and the bolt to hold the drive gear. Tighten the bolt to a torque of 55 7 N.m (41 5 lb.ft.).Install shaft assembly (12) on pump body.29. Use Tool group (A) and a press to install the bearing in idler gear (10).30. Put idler gear (10) in position on the shaft assembly. Install thrust plate (8) and the bolt to hold gear (10). Make sure the side of thrust plate (8), with the oil groove, is toward gear (10). The oil pump gears must turn freely by hand after assembly.31. Put the bolts, washers, brackets (5) and bracket (6) in position on pipe assembly (1). Put pipe assembly (1) in position on bell assembly (7) and tighten the bolts.32. Install O-ring seal (2) on pipe assembly (1).33. Install screen assembly (3) in bell assembly (7). Install clip (4) to hold screen assembly (3) in position.34. Put pipe assembly (1) in position in the pump body and install the bolt.End By:a. install oil pump


Parts plate JOHNSON:

0327944
PLATE,Throttle control
0327944 PLATE,Throttle control
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15RELEUC, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25ARECA, BJ25AREDC, BJ25AREUR, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25PL3EEM, BJ25PL3SIE, BJ25PL3SSB, B
0340268
 
0340268 PLATE, Rear
BJ40EEDS, BJ50BEEDS, J40EEOD, J40EERE, J50BEEOD, J50BEERE
0340269
 
0340269 PLATE, Applique
BJ40EEDS, BJ50BEEDS, J40EEOD, J40EERE, J50BEEOD, J50BEERE
0211943
 
0211943 PLATE, Rear
J40EEOD, J50BEEOD
0212770
 
0212770 PLATE, Rear
BJ40EEDS, BJ50BEEDS, J40EEOD, J50BEEOD
0212769
 
0212769 PLATE, Applique
BJ40EEDS, BJ40EEUC, BJ50BEEDS, BJ50RLEUC, J40EEOD, J50BEEOD
0341140
 
0341140 PLATE, Front
BJ40EEDS, BJ50BEEDS, J40EEOD, J50BEEOD
0212895
 
0212895 PLATE, Front
BJ40EEUC, BJ50RLEUC
Back to top