0304655 JOHNSON STOP,Drain leaf valve


0304655 STOP,Drain leaf valve JOHNSON 33E69A, 33E69A, 33E70M, 33E70M, 40E69R, 40E70A, 40E71B, 40ES69R, 40ES70A, 40R69R, 40R70A, 9R69S, 9R70A, 9R71R, MQ-14D, RD-30A, RDS-30A, RK-30A, RX-16M, V4A-20A, V4S-20A, VX-14B STOP
0304655 STOP,Drain leaf valve JOHNSON
Rating:
53

Buy STOP,Drain leaf valve 0304655 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 52
 

BRP JOHNSON entire parts catalog list:

33E69A, 33EL69A, 33R69A, 33RL69A 1969
33E69A, 33EL69A, 33R69A, 33RL69A 1969
33E70M, 33EL70M, 33R70M, 33RL70M 1970
33E70M, 33EL70M, 33R70M, 33RL70M 1970
40E69R, 40EL69R 1969
40E70A, 40EL70A 1970
40E71B, 40E71G, 40EL71B, 40EL71G, 40R71B, 40R71G, 40RL71B, 40RL71G 1971
40ES69R, 40ESL69R 1969
40ES70A, 40ESL70A 1970
40R69R, 40RL69R 1969
40R70A, 40RL70A 1970
9R69S, 9RL69S 1969
9R70A, 9R70C, 9RL70A, 9RL70C 1970
9R71R, 9RL71R 1971
MQ-14D, MQ-14E, MQL-14D, MQL-14E 1968
RD-30A, RD-30D, RD-30S, RDL-30A, RDL-30D, RDL-30S 1968
RDS-30A, RDS-30C, RDS-30D, RDS-30S, RDSL-30A, RDSL-30C, RDSL-30D, RDSL-30S 1968
RK-30A, RK-30C, RK-30D, RKL-30A, RKL-30C, RKL-30D 1968
RX-16M, RX-16R, RXE-16M, RXE-16R, RXEL-16M, RXEL-16R, RXL-16M, RXL-16R 1968
V4A-20A, V4AL-20A 1968
V4S-20A, V4SL-20A 1968
VX-14B, VXH-14B, VXHL-14B, VXL-14B 1968

Information:


Table 1
Diagnostic Trouble Codes
J1939 Code CDL Code Code Description
(code descriptions may vary) Comments
639-9 247-9 J1939 Network #1 : Abnormal Update Rate Another controller has incorrectly stopped transmitting a J1939 speed request (TSC1) or another controller has incorrectly started transmitting a J1939 speed request.
The ECM will log the diagnostic code.
The engine will not start.
1196-2 1639-2 Anti-theft Component Status States : Erratic, Intermittent, or Incorrect The Electronic Control Module (ECM) detects poor communications with the Machine Security System (MSS).
The engine warning lamp will come on and the ECM will log the diagnostic code.
The engine will not start.
1196-9 1639-9 Anti-theft Component Status States : Special Instruction The Electronic Control Module (ECM) detects a loss of communications with the Machine Security System (MSS).
The warning lamp will come on and the ECM will log the diagnostic code.
The engine will not start.
- 246-9 Proprietary CAN Data Link abnormal update rate The proprietary CAN data link cannot communicate correctly.
- 296-9 Transmission Control abnormal update rate The transmission control ECM cannot communicate correctly over the CAN data link with the engine ECM.
- 588-9 Monitor System Display abnormal update rate The engine ECM cannot communicate correctly over the CAN data link with the cab display panel.
- 1603-9 Machine Control Module abnormal update rate The machine control ECM cannot communicate correctly with the engine ECM over the CAN data link.
Follow the troubleshooting procedure to identify the root cause of the fault. Note: Refer to Troubleshooting, "Sensors and Electrical Connectors"for the locations of the components listed in this procedure.The following background information is related to this procedure:The CAN data link is also known as the J1939 data links. A data link is an industry standard for sending data between different devices in the same application.High speed data is transferred via the data link. The data link cannot be accurately tested without complicated equipment. The data link requires a resistance of 60 Ohms between the two wires to transmit the data correctly. This resistance is made up of two 120 Ohm resistors. The two resistors are known as "Terminating Resistors". The terminating resistors should be at opposite ends of a data link circuit. If this resistance is not present, then the data will be intermittent or unreadable.Note: The wiring for a J1939 data link is a twisted pair cable. If the wiring is damaged, the replacement type must be twisted pair cable.
Illustration 1 g06381127
Typical example of the schematic for the CAN data link
Illustration 2 g06381118
View of the pin locations for the CAN data link on the ECM Adapter connector
(20) CAN data link positive
(21) CAN data link negative
Illustration 3 g06384313
View of the pin locations for the CAN data link on the P2 connector
(48) CAN data link positive
(59) CAN data link negative
Table 2
Troubleshooting Test Steps Values Results
1. Use the "System Communication Status to Check the Status of the Other Devices on the Suspect CAN Data Link"
A. In the electronic service tool, click on the "Diagnostics" tab on the tool bar.
B. Select the "System Communication Status" option from the drop-down list.
Component Identified
Result: One or more of the devices on the suspect data link is not visible on the electronic service tool.
Repair: Thoroughly inspect the electrical connectors for the suspect devices
Refer to Troubleshooting, "Electrical Connectors - Inspect".
Check the power supply to the suspect devices.
If necessary, refer to Troubleshooting, "Electrical Power Supply - Test".
If the fault has been resolved, return the engine to service.
If the fault is still present, proceed to Test Step 2.
Result: All devices are visible on the electronic service tool.
Proceed to Test Step 2.
2. Check the Data Link Terminating Resistance at the ECM Adapter
A. Disconnect the ECM Adapter connector.
B. Measure the resistance between ECM Adapter pins 20 and 21.
Between 50 Ohms and 70 Ohms
Result: The resistance is less than 50 Ohms - there is a short circuit in the harness.
Repair: Repair the connectors or the harness and/or replace the connectors or the harness. Ensure that all the seals are correctly in place and ensure that the connectors are correctly connected.
Use the electronic service tool to clear all logged diagnostic codes and then verify that the repair eliminates the fault.
Result: The resistance is between 110 and 130 Ohms - one of the terminating resistors may have failed.
Repair: Locate the two terminating resistors and remove the two terminating resistors from the harness. Depending on the application, one or both of the terminating resistors may be located in other ECMs on the data link.
Measure the resistance of the two terminating resistors.
If one of the terminating resistors is incorrect, replace the faulty terminating resistor.
If the two terminating resistors are between 110 and 130 Ohms, proceed to Test Step 4.
Result: The resistance is greater than 150 Ohms.
Proceed to Test Step 3.
Result: The resistance is between 50 and 70 Ohms
The resistance is correct. The fault may be in the connection to other devices on the data link.
Proceed to Test Step 3.
3. Check the Data Link Wiring
A. Disconnect each of the connectors that connect other devices on the data link.
B. Use a multimeter to measure the resistance between ECM Adapter pin 20 and each of the CAN+ pins on other devices on the CAN data link.
C. Use a multimeter to measure the resistance between ECM Adapter pin 20 (ECM side) and pin (G) on the diagnostic connector.
D. Use a multimeter to measure the resistance between ECM Adapter pin 21 and each of the CAN- pins on other devices on the CAN data link.
E. Use a multimeter to measure the resistance between ECM Adapter pin 21 (ECM side) and pin (F) on the


Parts stop JOHNSON:

0312074
 
0312074 STOP,Steering handle
9R69S, 9R70A, 9R71R, 9R72M, 9R73B, MQ-14D
0304709
 
0304709 STOP,Leaf
33E69A, 33E69A, 33E70M, 33E70M, 40E69R, 40E70A, 40E71B, 40E72E, 40E73D, 40E74S, 40E75C, 40E76A, 40ES69R, 40ES70A, 40R69R, 40R70A, J40RSLR, J40RWCDB, J40RWCOM, J40RWCRA, RD-30A, RDS-30A, RK-30A, RX-16M
0310802
 
0310802 STOP,Shifter lock
33E69A, 33E69A, 33E70M, 33E70M, 40E69R, 40E70A, 40E71B, 40E72E, 40E73D, 40ES69R, 40ES70A, 40R69R, 40R70A, RD-30A, RDS-30A, RK-30A, RX-16M
0311864
 
0311864 STOP,Pinion
25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 33E69A, 33E69A, 33E70M, 33E70M, 40E69R, 40E70A, 40E71B, 40E72E, 40E73D, 40E74S, 40E75C, 40E76A, 40ES69R, 40ES70A, RDS-30A, RK-30A, RX-16M
0305379
 
0305379 STOP, Idle
40R69R, 40R70A, RD-30A
0204375
 
0204375 STOP,Pinion
V4S-20A, V4T-14B, VX-14B
Back to top