0316371 JOHNSON PLATE, Pulley


0316371 PLATE, Pulley JOHNSON 2R71A, 2R72M, 2R73B, 2R74E, 2R75D, 2R76S, 2R77C, 2R78R, 2R79A, 4R79D, J2RCSM, J4RLCSS PLATE
0316371 PLATE, Pulley JOHNSON
Rating:
63

Buy PLATE, Pulley 0316371 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 4
 

BRP JOHNSON entire parts catalog list:

2R71A 1971
2R72M 1972
2R73B 1973
2R74E 1974
2R75D 1975
2R76S 1976
2R77C 1977
2R78R 1978
2R79A 1979
4R79D, 4RL79D, 4W79D 1979
J2RCSM 1980
J4RLCSS, J4WCSS 1980

Information:

2. Disconnect the air lines from air starter (1).3. Fasten a strap and a suitable lifting device to air starter (1). Remove bolts (2) and remove the air starter from the flywheel housing. The weight of air starter (1) is 54 kg (120 lb). The following steps are for the installation of the air starter.4. Fasten a strap and a suitable lifting device to air starter (1). Put it and the gasket in position. Install bolts (2) that hold the air starter to the flywheel housing.5. Connect the air lines to air starter (1) and open the air pressure supply to the system.Disassemble Air Starter
Start By:a. remove air starter Make sure there is a complete set of new gaskets, vanes, seals and O-ring seals before the air starter is disassembled. 1. Remove elbow (1) from cover assembly (2).2. Remove silencer group (4) from motor housing (3). 3. Make marks to show the position of motor housing (3) in relation to gear case (7) for assembly purposes. Remove bolts (5) to remove gear case (7) and drive housing (6) as a unit from motor housing (3). 4. Use Tool (A) to remove ring (9) from drive gear (8). The air starter is a right hand model and bolt (10) has left hand threads. The bolt for a left hand model starter has right hand threads.5. Remove bolt (10) and washer (11) to remove drive pinion (12), a sleeve and spring from the end of the drive shaft.6. Make marks to show the position of drive housing (6) in relation to gear case (7) for assembly purposes. Remove bolts (13) and remove drive housing (6) from gear case (7). 7. Remove O-ring seal (14) from drive housing (6).
The drive shaft assembly, the piston and drive gear are under a spring force.
8. Install Tool (B) between drive gear (8) and piston (15). Use a press to make a compression of the piston return spring and remove the ring that holds the drive shaft assembly and piston in drive housing (6). 9. Slowly release the press to remove the force of piston return spring (17). Remove Tool (B) from between the drive gear and piston and remove ring (16) from the piston. Remove the drive gear, the piston and drive shaft assembly as a unit from drive housing (6). Remove piston return spring (17) from the drive housing. 10. Use a 5/16 " Allen Wrench to loosen the drive gear belt until the threads are free and remove drive shaft assembly (18) and piston (15) as a unit from drive gear (8). 11. Remove bulkhead (19) from piston (15). 12. Remove O-ring seals (20) from bulkhead (19). 13. Remove ring (21) from piston (15) and remove the piston from drive shaft assembly (18). Later model air starters will not have bumper (23).14. Remove O-ring seal (24), bumper (23) and seal (22) from piston (15). 15. Remove ring (33), cup (32) spring (31), driven clutch jaw (30), driving clutch jaw (29), bearing (28), washer (27), lockwasher (26) and bolt (25) from drive shaft assembly (18). Any time ring (34) is removed a replacement must be made.16. Remove ring (34) to remove bearing (35) from drive shaft (18). 17. Use Tool (C) to remove ring (37) and remove bearing (36) from gear case (7). Later model air starters will not have bumper (38) and backup ring (39).18. Remove bumper (38) from drive housing (6).19. Remove backup ring (39) from drive housing (6). 20. Remove seat (40) and bearing (41) from drive housing (6). 21. Remove seal (42) from drive housing (6). 22. Make marks to show the position of cover assembly (2) in relation to motor housing (3) for assembly purposes. Remove cover assembly (2) and an O-ring seal from motor housing (3). 23. Remove bolt (44) to remove rotor pinion (43) from rotor shaft. 24. Loosen setscrew (46) and remove nut (45) from the rotor shaft.25. Remove bearing (47) from end plate (48). 26. Remove O-ring seal (49) and end plate (48) from the end of the rotor. 27. Remove vanes (50) from rotor (51). 28. Remove rotor (51) from motor housing (3). 29. Use a press to remove bearing (52) and end plates (53) from rotor (51). 30. Remove bearing (52) from end plate (53). 31. Remove washers (54) from end plate (53). 32. Remove O-ring seals (55) from cylinder (56). 33. Remove cylinder (56) from motor housing (3). Remove the remainder of the O-ring seals from the cylinder.Assemble Air Starter
Clean all parts thoroughly. Put 2S3230 Bearing Lubricant on all bearings and the drive assembly. Put a thin layer of SAE 10W Oil on all other parts before assembly. 1. Install O-ring seals (1) on cylinder (2) and install the cylinder in housing (3). Make sure pin (5) is in alignment with opening (slot) (4) in housing (3). 2. Install O-ring seals (6) on cylinder (2). 3. Install end plate (7) on rotor (8). 4. Install O-ring seal (9) on the rotor shaft. 5. Install bearing (10) over the rotor shaft and


Parts plate JOHNSON:

0307561
 
0307561 PLATE,Swivel
10E74G, 10E75C, 10E76G, 10E77A, 10E78M, 10EL79B, 15E74G, 15E75C, 15E76A, 15E77M, 15E78B, 15E79E, 1R69C, 1R70R, 20R69B, 20R70C, 20R71S, 20R72R, 20R73A, 25E72R, 25E73A, 25E74M, 25E75B, 25E76E, 25E77S, 25E78C, 25E79R, 25R69B, 25R70C, 25R71S, 2R71A, 2R72
0313781
 
0313781 PLATE,Exhaust
1R69C, 1R70R, 2R71A, 2R72M, 2R73B, 2R74E, 2R75D, 2R76S, 2R77C, 2R78R, 2R79A, J2RCIB, J2RCNE, J2RCOC, J2RCRS, J2RCSM, J2RCTD, JCO-CCM, JCO-CDR, JCO-CEB, JCO-CUA, JCO-ESE, SC-10S
0203132
PLATE,Pump
0203132 PLATE,Pump
4R69B, 4R70E, 4R71D, 4R72S, 4R73C, 4R74R, 4R75A, 4R76M, 4R77B, 4R78E, 4R79D, J4RLCSS, J4WCIC, J4WCNR, JH-23A, LD-13B
0315000
PLATE,Leaf back-up
0315000 PLATE,Leaf back-up
2R71A, 2R72M, 2R73B, 2R74E, 2R75D, 2R76S, 2R77C, 2R78R, 2R79A, 4R69B, 4R70E, 4R71D, 4R72S, 4R73C, 4R74R, 4R75A, 4R76M, 4R77B, J2RCIB, J2RCNE, J2RCOC, J2RCRS, J2RCSM, J2RCTD, JCO-CCM, JCO-CDR, JCO-CUA
0321124
 
0321124 PLATE,Water pump
4R76M, J2RCOC, J4RLCSS, JCO-CCM, JCO-CDR, JCO-CEB, JCO-CUA, JCO-ESE
0323263
PLATE, Exhaust cover
0323263 PLATE, Exhaust cover
4R78E, 4R79D, BJ3REDS, BJ4BREDS, BJ4BREUC, BJ4RDHEDS, J3BRCEC, J3BRESR, J3REIA, J3RENM, J3REOD, J3RERE, J3RETB, J3REUC, J4BRCIC, J4BRECRJ, J4BRHCCS, J4BRHCDE, J4BRHCNR, J4BRHCOB, J4BRHCRM, J4BRHCTA, J4BRHCUD, J4RDHCCS, J4RDHCDE, J4RDHCEC, J4RDHCUD, J
0323485
 
0323485 PLATE, Leaf back-up
4R78E, 4R79D, BJ3REDS, BJ4BREDS, BJ4BREUC, BJ4RDHEDS, J3BRCEC, J3BRESR, J3RCCM, J3RCUA, J3REIA, J3RENM, J3REOD, J3RERE, J3RETB, J3REUC, J4BRCIC, J4BRECRJ, J4BRHCCS, J4BRHCDE, J4BRHCNR, J4BRHCOB, J4BRHCRM, J4BRHCTA, J4BRHCUD, J4RCCS, J4RCEC, J4RCUD, J
0582052
Back to top