0327782 PLATE, Impeller housing 2 JOHNSON
J100WMLCRS, J115MLCNB, J115MLCRD, J115MLCTE, J140MLCNB, J140MLCTE, J140TLCRD, J150STLCRD, J150STLCTE, J150TLCNM, J150TLCRD, J150TLCTB, J155WTLCRS, J175TLCNB, J175TLCTD, J185TLCRS, J200TLCNE, J200TLCTD, J235STLCRC, J235STLCTS, J235TLCNE, J235TLCRC, J2
PLATE
Price: query
Rating:
Compatible models:
BRP JOHNSON entire parts catalog list:
- GEARCASE » 0327782
J115MLCRD, J115TLCRD, J115TXCRD 1984
J115MLCTE, J115TLCTE, J115TXCTE 1983
J140MLCNB, J140TLCNB, J140TXCNB 1982
J140MLCTE, J140TLCTE, J140TXCTE 1983
J140TLCRD, J140TXCRD 1984
J150STLCRD 1984
J150STLCTE 1983
J150TLCNM, J150TXCNM 1982
J150TLCRD, J150TXCRD 1984
J150TLCTB, J150TLCTE, J150TXCTB, J150TXCTE 1983
J155WTLCRS, J155WTXCRS 1984
J175TLCNB, J175TXCNB 1982
J175TLCTD, J175TLCTE, J175TXCTD, J175TXCTE 1983
J185TLCRS, J185TXCR 1984
J200TLCNE, J200TXCNE 1982
J200TLCTD, J200TLCTS, J200TXCTD, J200TXCTS 1983
J235STLCRC 1984
J235STLCTS 1983
J235TLCNE, J235TXCNE 1982
J235TLCRC, J235TXCRC 1984
J235TLCTD, J235TLCTS, J235TXCTD, J235TXCTS 1983
J90MLCNB, J90TLCNB, J90TXCNB 1982
J90MLCRD, J90TLCRD, J90TXCRD 1984
J90MLCTE, J90TLCTE, J90TXCTE 1983
Information:
The connection of any electrical equipment and the disconnection of any electrical equipment may cause an explosion hazard which may result in injury or death. Do not connect any electrical equipment or disconnect any electrical equipment in an explosive atmosphere.
Test Step 1. Check Connectors for Moisture and Corrosion
Illustration 1 g01131211
Leaky seal at the connector (typical example)
Inspect all the harnesses. Ensure that the routing of the wiring harness allows the wires to enter the face of each connector at a perpendicular angle. Otherwise, the wire will deform the seal bore. Refer to Illustration 1. This will create a path for the entrance of moisture. Verify that the seals for the wires are sealing correctly.
Illustration 2 g01131276
Diagram for the installation of a sealing plug (typical example)
(1) ECM connector
(2) Correctly inserted plug
(3) Incorrectly inserted plug
Ensure that the sealing plugs are in place. If any of the plugs are missing, replace the plug. Ensure that the plugs are inserted correctly into the connector. Refer to Illustration 2.
Illustration 3 g01131019
Seal for an in-line connector (typical example)
Illustration 4 g01478122
Seal for a three-pin connector (typical example)
Illustration 5 g01131165
Seal for ECM connector (typical example)
Disconnect the suspect connector and inspect the connector seal. Ensure that the seal is in good condition. If necessary, replace the connector.
Thoroughly inspect the connectors for evidence of moisture entry. Note: It is normal to see some minor seal abrasion on connector seals. Minor seal abrasion will not allow the entry of moisture.If moisture or corrosion is evident in the connector, the source of the moisture entry must be found and the source of the moisture entry must be repaired. If the source of the moisture entry is not repaired, the fault will recur. Simply drying the connector will not fix the fault. Check the following items for the possible moisture entry path:
Missing seals
Incorrectly installed seals
Nicks in exposed insulation
Improperly mated connectorsMoisture can also travel to a connector through the inside of a wire. If moisture is found in a connector, thoroughly check the connector harness for damage. Also check other connectors that share the harness for moisture.Note: The ECM is a sealed unit. If moisture is found in an ECM connector, the ECM is not the source of the moisture. Do not replace the ECM.Expected Result:The harness, connectors, and seals are in good condition. There is no evidence of moisture in the connectors.Results:
OK - The harness, connectors, and seals are in good condition. Proceed to Test Step 2.
Not OK - A fault has been found with the harness or the connectors.Repair: Repair the connectors or the wiring, as required. Ensure that all of the seals are correctly installed. Ensure that the connectors have been reattached.If corrosion is evident on the pins, sockets or the connector, use only denatured alcohol to remove the corrosion. Use a cotton swab or a soft brush to remove the corrosion.If moisture was found in the connectors, run the engine for several minutes and check again for moisture. If moisture reappears, the moisture is wicking into the connector. Even if the moisture entry path is repaired, it may be necessary to replace the wires.Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair eliminates the fault.STOPTest Step 2. Check the Wires for Damage to the Insulation
Carefully inspect each wire for signs of abrasion, nicks and cuts. Inspect the wires for the following conditions:
Exposed insulation
Rubbing of a wire against the engine
Rubbing of a wire against a sharp point
Check all of the fasteners for the harness and the strain relief components on the ECM in order to verify that the harness is correctly secured. Also check all of the fasteners in order to verify that the harness is not compressed. Pull back the harness sleeves in order to check for a flattened portion of wire. A fastener that has been overtightened flattens the harness. This damages the wires that are inside the harness. Expected Result:The wires are free of abrasion, nicks and cuts and the harness is correctly clamped.Results:
OK - The harness is OK. Proceed to Test Step 3.
Not OK - There is damage to the harness.Repair: Repair the wires or replace the wires, as required. Use the electronic service tool in order to clear all logged diagnostic codes and then verify that the repair eliminates the fault.STOPTest Step 3. Inspect the Connector Terminals
Visually inspect each terminal in the connector. Verify that the terminals are not damaged. Verify that the terminals are correctly aligned in the connector and verify that the terminals are correctly located in the connector. Expected Result:The terminals are correctly aligned and the terminals appear undamaged.Results:
OK - The terminals are OK. Proceed
Parts plate JOHNSON:
0317762
0317762 PLATE, Lower bearing
100ML79S, 115EL77S, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL76S, 200TL77C, 200TL78R, 200TL79A, 235TL70A, 23
0318272
0318272 PLATE
100ML79S, 115EL77S, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL77C, 200TL78R, 200TL79A, 235TL70A, 235TL78R, 50
0321176
0321176 PLATE,Impeller
100ML79S, 115EL77S, 115ETZ78C, 115ML79R, 115TXL77S, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL76S, 200TL77C, 200TL78R, 200TL79A, 235TL70A, 235TL78R, 85EL76D, 85EL77S, 85ETLR78C, 85ML79R, 85TXLR77S, J100MLCSC
0327097
0327097 PLATE BRUSH (included in item 4)
J100MLCSC, J115MLCIH, J115MLCNB, J115MLCSA, J115MLCTE, J140MLCIH, J140MLCNB, J140MLCSA, J140MLCTE, J70ELCIH, J70ELCNB, J70ELCSA, J75ECNB, J75ERCIH, J75ERCSA, J85MLCSA, J90MLCIH, J90MLCNB, J90MLCTE
0210033
0210045
0210034
0329715