0331990 JOHNSON PLATE, Front, 115 only


0331990 PLATE, Front, 115 only JOHNSON J115MLCOS, J90MLCOS PLATE
0331990 PLATE, Front, 115 only JOHNSON
Rating:
38

Buy PLATE, Front, 115 only 0331990 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 23
 

Compatible models:

BRP JOHNSON entire parts catalog list:

J115MLCOS, J115TLCOS 1985
J90MLCOS, J90TLCOS, J90TXCOS 1985

Information:


Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 230-6284 Timing Pin (Camshaft) 1
C 136-4632 Timing Pin (Crankshaft) 1
268-1966 Adapter 1
D 9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02717945
If necessary, use Tooling (A) to ensure that number one piston is at top dead center on the compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.
Ensure that Tooling (B) is installed in Hole (Y) in the cylinder block. Use Tooling (B) in order to lock the crankshaft in the correct position. Note: Do not use excessive force to install Tooling (B). Do not use Tooling (B) to hold the crankshaft during repairs.
Illustration 2 g02712440
Alignment of timing marks
Ensure that Tooling (C) is installed into Hole (X) in camshaft gear (1).
Illustration 3 g02718564
Clean idler gear (3) and inspect the idler gear for wear or damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary, replace the idler gear.
Clean hub (11) and inspect the hub for wear or damage. Refer to Specifications, "Gear Group (Front)" for more information. If necessary, replace the hub.
Lubricate hub (11) with clean engine oil. Slide hub (11) into idler gear (3). Ensure that the timing marks are toward the front of the idler gear.
Illustration 4 g02718572
Align the timing mark on idler gear (3) with the timing mark on the camshaft gear. Refer to the illustration 2. Install the assembly of idler gear (3) and hub (11) into the recess in the timing case. Ensure that oil Hole (Z) is to the top of the hub. Note: The idler gear must be tilted during installation. Ensure that the holes in the hub are aligned with the holes in the cylinder block.
Clean plate (9) and inspect the plate for wear or damage. If necessary, replace the plate.
Lubricate plate (9) with clean engine oil. Align the holes in plate (9) with the holes in hub (11). Install the plate in the original orientation.
Install bolts (10).
Remove Tooling (B) and Tooling (C). Note: Ensure that timing marks are aligned, before removing Tooling (B) and Tooling (C).
Tighten bolts (10) to a torque of 44 N m (32 lb ft).
Use Tooling (D) in order to measure the end play of the camshaft gear. Refer to Specifications, "Gear Group (Front)" for more information.
Use Tooling (D) in order to measure the backlash between the idler gear and the camshaft gear. Refer to Specifications, "Gear Group (Front)" for more information.
Use Tooling (D) in order to measure the backlash between the idler gear and the crankshaft gear. Refer to Specifications, "Gear Group (Front)" for more information.
Illustration 5 g02712439
Install a new O-ring seal (4) to plug (5). Install plug (5) to the cylinder block. Tighten plug (5) to a torque of 21 N m (186 lb in).
Lightly lubricate all of the gears with clean engine oil. End By:
Install the fuel injection pump gear. Refer to Disassembly and Assembly, "Fuel Pump Gear - Install".
Adjust the engine valve lash. Refer to System Operation, Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust" for the correct procedure.


Parts plate JOHNSON:

0317762
 
0317762 PLATE, Lower bearing
100ML79S, 115EL77S, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL76S, 200TL77C, 200TL78R, 200TL79A, 235TL70A, 23
0318272
 
0318272 PLATE
100ML79S, 115EL77S, 115ESL73M, 115ESL74B, 115ESL75E, 115ETZ78C, 115ML79R, 115TXL77S, 135ESL73M, 135ESL74B, 135ESL75E, 140ML77S, 140ML78C, 140ML79R, 150TL78S, 150TL79C, 175TL77S, 175TL78C, 175TL79R, 200TL77C, 200TL78R, 200TL79A, 235TL70A, 235TL78R, 50
0210086
 
0210086 PLATE, Applique front
J115MLCOS, J90MLCOS
0329933
 
0329933 PLATE, Rear
J115MLCOS, J90MLCOS
0329931
 
0329931 PLATE, Front, 90 only
J115MLCOS, J90MLCOS
0330380
 
0330380 PLATE, Impeller hsg.
CJ275TLCDC, CJ275TLCOS, CJ300TLCDC, CJ300TLCOS, D100WTLM, J100STLCCA, J100STLCEM, J100STLEIE, J100STLEND, J100STLESB, J100WMLCDR, J100WMLCOC, J100WTLCUA, J100WTLEIB, J100WTLENE, J100WTLESM, J100WTLZ, J110MLCCA, J110MLCDC, J110MLCEM, J110MLCUR, J115JL
0330383
 
0330383 PLATE, Impeller hsg., chrome
CJ275TLCDC, CJ300TLCDC, CJ300TLCOS, D100WTLM, J100STLCCA, J100STLCEM, J100STLEIE, J100STLEND, J100STLESB, J100WMLCDR, J100WMLCOC, J100WTLCUA, J100WTLEIB, J100WTLENE, J100WTLESM, J100WTLZ, J110MLCCA, J110MLCDC, J110MLCEM, J110MLCUR, J115JLEIE, J115JLE
0331022
 
0331022 PLATE, Mount
BJ115TLEDA, D100WTLM, HJ88MSLEDC, HJ88MSLEDC, J100STLCCA, J100STLCEM, J100STLEIE, J100STLEND, J100STLERC, J100STLESB, J100STLETS, J100WMLCDR, J100WMLCOC, J100WTLCUA, J100WTLEDR, J100WTLEIB, J100WTLENE, J100WTLEOC, J100WTLERS, J100WTLESM, J100WTLETD,
Back to top