0341137 JOHNSON PLATE, Frame, rear, 35


0341137 PLATE, Frame, rear, 35 JOHNSON HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREOR, J25REOR, J30REOB, SJ35REDE PLATE
0341137 PLATE, Frame, rear, 35 JOHNSON
Rating:
53

Buy PLATE, Frame, rear, 35 0341137 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme: 18
 

BRP JOHNSON entire parts catalog list:

HJ20CREDA, HJ20CRLEDA, J20CREDA, J20CRLEDA 1996
HJ25RLEDA, J25REDA, J25RLEDA, SJ25REDA, SJ25RLEDA 1996
HJ30REDE, HJ30RLEDE, J30REDE, J30RLEDE, SJ30REDE, SJ30RLEDE 1996
J20CREOR, J20CRLEOR 1995
J25REOR, J25RLEOR 1995
J30REOB, J30RLEOB 1995
SJ35REDE, SJ35RLEDE 1996

Information:


Illustration 1 g01181798
Schematic for the engine speed/timing sensors
Test Step 1. Check for Diagnostic Codes
Connect Cat ET to the service tool connector. Refer to Troubleshooting, "Electronic Service Tools".
Restore electrical power to the engine ECM.
Start the engine and run the engine until the engine is at the normal operating temperature. Note: If the engine will not start, monitor the engine rpm on Cat ET while the engine is being cranked. Cat ET may need to be powered from another battery while the engine is being cranked.
Wait at least 30 seconds for activation of the diagnostic codes. Look for these codes on Cat ET:
190-02
190-11
342-02
342-11Expected Result:One or both of the diagnostic codes that are listed above are logged or active.Note: If the engine will not start and Cat ET displayed 0 rpm during cranking, select "No Engine rpm".Results:
No Engine rpm - Engine rpm is not indicated on Cat ET. Proceed to Test Step 2.
Active or logged code - There is an active diagnostic code or a logged diagnostic code for an engine speed/timing sensor. Proceed to Test Step 4.
No codes - Neither code is active or logged.Repair: Refer to the appropriate symptoms in Troubleshooting, "Troubleshooting Without a Diagnostic Code".STOPTest Step 2. Check the Installation of the Sensor Assembly
Remove electrical power from the engine ECM.
Illustration 2 g01180490
Left side view
(1) Engine
(2) Mounting flange
(3) Bracket
Visually inspect the sensor assembly without removing the sensor assembly from the engine. Flanges (2) must be flush against engine (1) in order to ensure proper operation. Inspect bracket (3). Verify that the bracket securely holds the flanges of the sensors flush against the engine.Verify that the bracket is not bent. If the bracket is bent or if an obstruction is preventing the sensor assembly from being installed correctly, the engine will not start.Note: The bracket cannot be replaced separately.
Remove the sensor assembly from the engine.
Illustration 3 g01180501
Exploded view of the engine speed/timing sensors
(4) O-ring seals
Ensure that one O-ring (4) is installed on each sensor. Check the O-rings for damage. Replace the O-rings, if necessary. Results:
OK - The sensor assembly's components are OK.Repair: Perform the following procedure in order to properly install the sensor assembly:
Lubricate each O-ring with engine oil.
Fully seat the sensor assembly in the engine. Note: If the sensor assembly will not fully seat into the engine, replace the sensor assembly.
Tighten the bracket bolt.
Connect the sensor's electrical connectors. Verify that the connectors are latched on both sides.
Ensure that the harness is properly secured, and that the tie-wraps are placed in the correct location. Proceed to Test Step 3.
Not OK - At least one of the sensor assembly's components is not OK.Repair: Obtain a new sensor assembly. Perform the following procedure in order to properly install the sensor assembly:
Lubricate each O-ring with engine oil.
Fully seat the sensor assembly in the engine. Note: If the sensor assembly will not fully seat into the engine, replace the sensor assembly.
Tighten the bracket bolt.
Connect the sensor's electrical connectors. Verify that the connectors are latched on both sides.
Ensure that the harness is properly secured, and that the tie-wraps are placed in the correct location. Verify that the problem is resolved.STOPTest Step 3. Inspect the Electrical Connectors and the Wiring
Illustration 4 g01181799
Left side engine view (typical example)
(5) J401/P401 connector for the primary engine speed/timing sensor
(6) J402/P402 connector for the secondary engine speed/timing sensor
(7) J2/P2 ECM connector
Thoroughly inspect connectors (5), (6), and (7). Refer to Troubleshooting, "Electrical Connectors - Inspect".
Illustration 5 g01181800
Left side view
(P2-48) Primary engine speed/timing sensor +
(P2-49) Primary engine speed/timing sensor -
(P2-58) Secondary engine speed/timing sensor +
(P2-59) Secondary engine speed/timing sensor -
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the engine speed/timing sensors.
Check the allen hea


Parts plate JOHNSON:

0324318
PLATE,Leaf
0324318 PLATE,Leaf
25E79R, 35E79A, BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ30EECS, BJ30EEDE, BJ30EEEC,
0327944
PLATE,Throttle control
0327944 PLATE,Throttle control
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15RELEUC, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25ARECA, BJ25AREDC, BJ25AREUR, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25PL3EEM, BJ25PL3SIE, BJ25PL3SSB, B
0337611
 
0337611 PLATE, Frame, rear, 25
BJ20SEEDA, BJ20SREDA, BJ25BAEDR, BJ25EEDM, BJ30BAEDE, BJ30EEDE, HJ20CREDA, HJ25RLEDA, HJ25TELEDA, HJ30REDE, J20CREND, J20CREOR, J20CRERC, J20CRETS, J20EEND, J20EEOR, J20EERC, J20EETS, J25EENS, J25EEOA, J25EERR, J25EETC, J25REND, J25REOR, J25RERC, J25
0212715
 
0212715 PLATE, Frame, front, 35
HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREOR, J25REOR, J30REOB, SJ35REDE
0212709
 
0212709 PLATE, Frame, front, 20
BJ20SEEDA, BJ20SEEUM, BJ20SREUM, BJ25BAEUA, BJ25EEDM, BJ25EEUB, BJ30BAEUD, BJ30EEDE, BJ30EEUD, HJ20CREDA, HJ25RLEDA, HJ30REDE, J20CREOR, J20EEOR, J25EEOA, J25REOR, J30EEOB, J30REOB, SJ35REDE
0212713
 
0212713 PLATE, Frame, front, 30
BJ20SEEDA, BJ20SEEUM, BJ20SREDA, BJ20SREUM, BJ25BAEDR, BJ25BAEUA, BJ25EEDM, BJ25EEUB, BJ30BAEDE, BJ30BAEUD, BJ30EEDE, BJ30EEUD, HJ20CREDA, HJ25RLEDA, HJ25TELEDA, HJ30REDE, J20CREOR, J20EEOR, J25EEOA, J25REOR, J25TEEOR, J25TEEUM, J30EEOB, J30REOB, J30
0212711
 
0212711 PLATE, Frame, front, 25
BJ20SEEDA, BJ20SEEUM, BJ20SREDA, BJ20SREUM, BJ25BAEDR, BJ25BAEUA, BJ25EEDM, BJ25EEUB, BJ30BAEDE, BJ30BAEUD, BJ30EEDE, BJ30EEUD, HJ20CREDA, HJ25FPO, HJ25FPV, HJ25RLEDA, HJ25TELEDA, HJ30REDE, J20CREOR, J20EEOR, J25EEOA, J25REOR, J25TEEOR, J25TEEUM, J30
0341135
 
0341135 PLATE, Frame, rear, 30
BJ20SEEDA, BJ25EEDM, BJ30EEDE, HJ20CREDA, HJ25RLEDA, HJ25TELEDA, HJ30REDE, J20CREOR, J20EEOR, J25EEOA, J25REOR, J25TEEOR, J30EEOB, J30REOB, J30TEEDE, J30TEEOB, SJ35REDE
Back to top