0345515 PLATE, Frame, front JOHNSON
BJ25EEED, BJ30BAEEC, BJ30EEEC, J25JREEM, J25TEEEE, J25WRLSIR, J25WRLSSC
PLATE
Price: query
Rating:
BRP JOHNSON entire parts catalog list:
- ENGINE COVER » 0345515
BJ30EEEC, BJ30EEEN, BJ30ELEEC, BJ30ELEEN, J30EEEC, J30EEEN, J30ELEEC, J30ELEEN 1999
J25JREEM, J25JREEN, J25REEB, J25REEN, J25RLEEB, J25RLEEN, SJ25RDEEM, SJ25RDEEMN, SJ25RTEEM 1999
J25TEEEE, J25TEEEN, J25TELEEE, J25TELEEN 1999
J25WRLSIR, J25WRSIR 2001
J25WRLSSC, J25WRSSC 2000
Information:
Illustration 1 g01269664
Typical schematic for the CAN data linkTest Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 2 g01121169
Typical engine components for the CAN data link (1) Connector for the electronic service tool (2) Customer connector (3) J1/P1 connectors
Thoroughly inspect connectors (1), (2), and (3). Thoroughly inspect the connectors for each module that is connected to the CAN data link. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Illustration 3 g01269470
P1 terminals that are associated with the CAN data link (P1-34) CAN data link − (P1-50) CAN data link +
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the CAN data link.
Check the allen head screw on each ECM connector for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for the correct torque values.
Check the allen head screw on the customer connector for the proper torque. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect" for the correct torque value.
Check the wiring harnesses for abrasion, for corrosion and for pinch points.Expected Result:All connectors, pins and sockets are completely coupled and/or inserted. The harness and wiring are free of corrosion, of abrasion and of pinch points.Results:
OK - The harness and the wiring appear to be OK. Proceed to Test Step 2.
Not OK - There is a problem in the wiring harness.Repair: Repair the connectors and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the problem is resolved.STOPTest Step 2. Verify the Proper Installation of the CAN Data Link
Disconnect any module that is connected to the CAN data link.
Disconnect the P1 connector and measure the resistance between terminals P1-50 (CAN data link +) and P1-34 (CAN data link -).Expected Result:The resistance is between 108 and 132 Ohms.Results:
OK - The resistance is between 108 and 132 Ohms.Repair: If the CAN data link is working properly at this time, there may be an intermittent problem. If the problem is intermittent, refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".STOP
Not OK - The resistance is not between 108 and 132 Ohms. The terminating resistor is missing.Repair: The engine is shipped with one terminating resistor that is installed between the ECM and the customer connector.Refer to the appropriate electrical schematic in order to determine the missing resistor. Replace the missing resistor. Verify that the problem is resolved.STOP
Not OK - The resistance is less than 108 Ohms. Proceed to Test Step 3.
Not OK - The resistance is greater than 132 Ohms. Proceed to Test Step 4.Test Step 3. Check for a Short Circuit
Disconnect the J1/P1 ECM connector.
Remove the terminating resistors from the CAN data link.
If a J1939 display is installed, disconnect the display.
Measure the resistance between the points that are listed in Table 1. Be sure to wiggle the wires in the harnesses as you make each resistance measurement.
Table 1
Resistance Measurements for the CAN Data Link    
Connector and Terminal    Terminal    
P1-50 (CAN data link +)     All of the other terminals on the P1 connector    
Engine ground
P1-34 (CAN data link -)     All of the other terminals on the P1 connector    
Engine ground Expected Result:Each check of the resistance indicates an open circuit.Results:
OK - Each check of the resistance indicates an open circuit. Proceed to Test Step 4.
Not OK - At least one check of the resistance does not indicate an open circuit. There is a short circuit in a harness. There may be a problem with a connector.Repair: Repair the wiring and/or the connector. Replace part, if necessary. Verify that the problem is resolved.STOPTest Step 4. Check for an Open Circuit
Verify that all of the connections are disconnected.
Fabricate a jumper wire. Use the jumper wire in order to create a short circuit between terminals G and F on the service tool connector.
Measure the resistance between terminals P1-50 (CAN data link +) and P1-34 (CAN data link -).
Remove the jumper wire from the service tool connector.Expected Result:The resistance is less than ten Ohms.Results:
OK - The resistance is less than ten Ohms. There is not an open circuit.Repair: If the problem is intermittent, perform the diagnostic functional test Troubleshooting, "Electrical Connectors Inspect".STOP
Not OK - The resistance is more than ten Ohms. There is an open circuit or excessive resistance in the circuit. There may be a problem in a connector.Repair: Repair the wiring and/or the connector. Replace part, if necessary. Verify that the problem is resolved.STOP
Parts plate JOHNSON:
0323251
0323251 PLATE, Impeller housing
25E78C, 25E79R, 35E78R, 35E79A, BJ20SRECB, BJ20SREUM, BJ25BAECM, BJ25BAEUA, BJ30BAECS, BJ30BAEEC, BJ30BAEUD, J25JREDC, J25JREEM, J25JREOS, J25JRSIE, J25JRSSB, J30RLSIA, J30RLSSR
0324318
0324318 PLATE,Leaf
25E79R, 35E79A, BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, BJ30EECS, BJ30EEDE, BJ30EEEC,
0208424
0208424 PLATE, Handle support, evinrude
BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ30BAECS, BJ30BAEDE, BJ30BAEEC, BJ30BAEUD, D25RWA, HJ20CREDA, HJ25FPO, HJ25FPV, HJ25RLEDA, HJ30REDE, J20CRCCA, J20CRCDC, J20CRCEM, J20CRCUR, J20CREIE, J20CREND, J20CREOR, J20CRERC, J2
0328755
0328755 PLATE,Impeller housing
BJ20SEECB, BJ20SEEDA, BJ20SEEUM, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25ARECA, BJ25AREDC, BJ25AREUR, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25EECE, BJ25EEDM, BJ25EEED, BJ25EEUB, BJ25ELSIC, BJ25ELSSS, BJ25PL3EEM, BJ25PL3SIE, BJ25PL3SSB, BJ30BAECS, BJ30BAEDE
0327944
0327944 PLATE,Throttle control
BJ10EEDD, BJ10FAEDC, BJ10FAEUR, BJ10RELEUS, BJ10RHLSDA, BJ10RHLSOR, BJ10RHLSRC, BJ10RHLSTS, BJ15EEDS, BJ15RELEUC, BJ20SRECB, BJ20SREDA, BJ20SREUM, BJ25ARECA, BJ25AREDC, BJ25AREUR, BJ25BAECM, BJ25BAEDR, BJ25BAEUA, BJ25PL3EEM, BJ25PL3SIE, BJ25PL3SSB, B
0213235
0345516
0345517