5032170 JOHNSON PROPELLER NUT KIT


5032170 PROPELLER NUT KIT JOHNSON BJ25E4SDS, BJ25E4SUC, BJ25R4SDS, BJ25R4SUC, BJ25TE4SDS, BJ25TE4SUC, J25PL4SOC, J25PL4SRS, J30PL4SDR, J30PL4SOC, J30PL4SRS, J30PL4SUA, J30TEL4SDR, J30TEL4SUA PROPELLER
5032170 PROPELLER NUT KIT JOHNSON
Rating:
13

Buy PROPELLER NUT KIT 5032170 JOHNSON genuine, new aftermarket parts with delivery
Number on catalog scheme:
 

BRP JOHNSON entire parts catalog list:

BJ25E4SDS, BJ25EL4SDS, J25E4SDC, J25EL4SDC 2006
BJ25E4SUC, BJ25EL4SUC, J25E4SUR, J25EL4SUR 2007
BJ25R4SDS, BJ25RL4SDS, J25R4SDC, J25RL4SDC 2006
BJ25R4SUC, BJ25RL4SUC, J25R4SUR, J25RL4SUR 2007
BJ25TE4SDS, BJ25TEL4SDS, J25TE4SDC, J25TEL4SDC 2006
BJ25TE4SUC, BJ25TL4SUC, J25TE4SUR, J25TEL4SUR 2007
J25PL4SOC, J25TEL4SOC 2005
J25PL4SRS 2004
J30PL4SDR 2006
J30PL4SOC, J30TEL4SOC 2005
J30PL4SRS 2004
J30PL4SUA 2007
J30TEL4SDR 2006
J30TEL4SUA 2007

Information:


Illustration 1 g01276499
Schematic for the digital sensor supplyTest Step 1. Inspect the Electrical Connectors and the Wiring
Remove the electrical power from the ECM.
Illustration 2 g01183529
Location of the J1/P1 ECM connectors (typical left side engine view)
Thoroughly inspect the J1/P1 ECM connectors. Inspect the connectors for each digital sensor. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Illustration 3 g01234119
P1 ECM connector (P1-4) +8 VDC (P1-5) Return (P1-66) Throttle position signal
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the digital sensor supply.
Check the torque of the allen head screws for the ECM connectors. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".
Check the harness and wiring for abrasions and for pinch points from the battery to the ECM.Expected Result:All of the connectors, pins, and sockets are completely coupled and/or inserted, and the harness and wiring are free of corrosion, of abrasion or of pinch points.Results:
OK - The connectors and the wiring are OK. Proceed to Test Step 2.
Not OK - There is a problem with a connector and/or the wiring.Repair: Repair the connector and/or the wiring. Replace parts, if necessary. Ensure that all of the seals are properly in place and ensure that the connectors are completely coupled. Verify that the problem is resolved.STOPTest Step 2. Check for Active Diagnostic Codes
Connect the Caterpillar Electronic Technician (ET) to the service tool connector. Refer to electronic troubleshooting Troubleshooting, "Electronic Service Tools".
Restore the electrical power to the ECM.
Observe the active diagnostic code screen on Cat ET. Wait at least 30 seconds so that any codes may become active. Look for these codes:
041-03 8 Volt DC Supply short to +batt
041-04 8 Volt DC Supply short to groundExpected Result:One of the above diagnostic codes is active.Results:
Active 03 code - A 03 diagnostic code is active. Proceed to Test Step 3.
Active 04 code - A 04 diagnostic code is active. Proceed to Test Step 4.
No active codes - None of the above codes are active.Repair: If any of the above codes are logged and the engine is not running properly, refer to Troubleshooting, "Troubleshooting Without a Diagnostic Code".If the engine is running properly at this time, there may be an intermittent problem in a harness that is causing the codes to be logged. Refer to the diagnostic functional test Troubleshooting, "Electrical Connectors - Inspect".STOPTest Step 3. Check the Voltage on the +8 V Supply Wire
Remove the electrical power from the ECM.
Disconnect the harness connector for the throttle sensor.
Restore the electrical power to the ECM.
Measure the voltage between terminals A and B at the harness connector for each sensor.Expected Result:Each voltage measurement is 8.0 0.4 VDC.Results:
OK - Each voltage measurement is 8.0 0.4 VDC.Repair: Connect the sensor connector. Clear all diagnostic codes. Check for active diagnostic codes. If the problem is intermittent, refer to the diagnostic functional test Troubleshooting, "Electrical Connectors


Parts propeller JOHNSON:

5032109
 
5032109 PROPELLER (3X10-1/4X12)
J25PL4SOC, J25PL4SRS, J30PL4SOC, J30PL4SRS
5032110
 
5032110 PROPELLER (3X10-1/4X13)
J25PL4SOC, J25PL4SRS, J30PL4SOC, J30PL4SRS
5032108
 
5032108 PROPELLER (3X10-1/4X11)
J25PL4SOC, J25PL4SRS, J30PL4SOC, J30PL4SRS
5032171
 
5032171 PROPELLER (3X10-1/4X9)
J25PL4SOC, J25PL4SRS, J30PL4SOC, J30PL4SRS
5032107
 
5032107 PROPELLER (3X10-1/4X10)
J25PL4SOC, J25PL4SRS, J30PL4SOC, J30PL4SRS
5032106
 
5032106 PROPELLER (3X10-1/4X14)
J25PL4SOC, J25PL4SRS, J30PL4SOC, J30PL4SRS
Back to top