0115524 RECOIL SPRING JOHNSON
BJ2REDE, BJ2REUD, BJ3ROEDE, BJ3ROEUD, HJ2DRETC, HJ3REIC, HJ3RENR, HJ3RETC, J2RECS, J2REEC, J2ROEOB, J2RTSIA, J2RTSSR, J2WREES, J2WRSIR, J2WRSSC, J3REEC, J3ROECS, J3ROEOB, J3RSDE, J3RSNF, J3RSOD, J3RSRE, J3RSTB, J3RTLSIA, J3RTLSSR, J3WREES, J3WRSIR, J
RECOIL
Price: query
Rating:
You can buy parts:
As an associate, we earn commssions on qualifying purchases through the links below
Compatible models:
BRP JOHNSON entire parts catalog list:
- RECOIL STARTER ASSEMBLY » 0115524
BJ3ROEDE, HJ3ROEDE, HJ3RSA, J3ROEDE, SJ3ROEDE 1996
BJ3ROEUD, HJ3ROEUD, HJ3RSK, J3ROEUD, SJ3ROEUD 1997
HJ2DRERM, HJ2DRETC 1993,1994
HJ3REIC 1991
HJ3RENR 1992
HJ3RERM, HJ3RETC 1993,1994
J2RECS, J2RSS 1998
J2REEC 1999
J2ROEOB 1995
J2RTSIA, J2RTVSIA 2001
J2RTSSR 2000
J2WREES 1999
J2WRSIR 2001
J2WRSSC 2000
J3REEC, J3RLEEC 1999
J3ROECS, J3ROLECS, J3RSS 1998
J3ROEOB 1995
J3RSDE 2006
J3RSNF 2002
J3RSOD 2005
J3RSRE 2004
J3RSTB, J3RSTF 2003
J3RTLSIA, J3RTSIA, J3RTVSIA 2001
J3RTLSSR, J3RTSSR 2000
J3WREES 1999
J3WRSIR 2001
J3WRSSC 2000
Information:
Specification
Construction
Governor System Component Parts(1) Sealing metal(2) Sealing wire(3) Low- and high-speed(4) Governor spring(5) Sliding shaft(6) Stopper(7) Governor spring(8) Governor shaft(9) Governor lever(10) Tie-rod(11) Tie-rod clip(12) Tie-rod cover(13) tie-rod cover gasket(14) Tension lever(15) Start spring(16) Governor spring lever(17) Speed control lever assembly(18) Cover assembly(19) Governor cover gasket(20) Return spring(21) Stop lever assembly(22) O-ring(23) Snap ring(24) Stop lever(25) Grooved pin (3 x 20)(26) Grooved pin (3 x 14)(27) Torque spring set(28) Sealing capTORQUE SPRING
Installation of Torque Spring Set
Install and adjust the torque spring set using the following procedure:(1) Set the speed control lever to the high-idling speed position by adjusting the high-speed set bolt.(2) Turn in the torque spring set until engine speed drops about 50 rpm from high-idling speed.(3) From this position, turn back the torque spring set by the specified number of turns (N.) Lock the torque spring set at that position with the special nut.(4) Install the torque spring set sealing cap and stake the cap to prevent loosening. CAUTION There are two types of torque spring set: The single spring type and the double-spring type. Since each torque spring set has been adjusted precisely during assembly, do not tamper with the adjust screw unless it is necessary.
Torque spring setAssembling the Torque Spring Set
When the torque spring set has been disassembled or its component parts have been replaced, reassemble and adjust the torque spring set using the following procedure:
Assembling torque spring setSingle spring type
When installing the single-spring type torque spring set, use the following steps.(1) Lightly turn in adjust screw (5) (with a screw-driver operated by fingertips) until a resistance to screw rotation is felt. Lightly lock the screw at that position with locknut (4).(2) Set the scale to the zero-point. Turn in the spring case (2) until the value of load "A" shown in table below can be attained. Lock the spring case at that position with special nut (3).(3) Temporarily loosen adjust screw (5) until the value of load "A" is reduced by about 200 grams, and then retighten the screw until the value of "B" is attained. Lock the screw at that position with locknut (4).Adjust screw tightening torque: 0.8 to 1.2 kg.(4) To inspect the torque spring set for properly adjusted spring load, use a testing arrangement such as shown in the figure at right. Gradually push the scale against the torque spring set until the stopper (1) is moved (or the pointer of dial gauge deflects). Check that the load applied to the torque spring at that moment coincides with the value of load "C".
Setting of Torque Spring CHECKING
Replace the gear case and inspect the governor. When removing the gear case, be sure to remove the tie-rod cover by the side of the fuel pump and disconnect the tie-rod from the rack.If any parts are found defective, replace them.
Inspecting Torque Spring CAUTION When the governor is assumed to be malfunctioning, check the bearing on the gear case side, too.
Inspection Governor System PartsRemoval and Installation
(Refer to I-06 GEAR CASE AND OIL PUMP.)Removal(1) Removing the levers(a) to remove the levers, pull out the grooved pins which have been driven into the governor lever, stop lever, and speed control lever.(b) Loosen bolts fastening the levers and shafts.(2) InstallationInstall the levers and shafts, one after another, checking for proper function of them.
Installing Speed Control Lever CAUTION1. After press-fitting each grooved pin, check the shaft for smooth rotation.2. Coat the O-rings with oil before installing them.3. No deflection exceeding 20 mm is permitted for the governor spring installed.4. Install the governor spring lever and speed control lever so that play of angle between levers (standard: 5°) is minimized.
Construction
Governor System Component Parts(1) Sealing metal(2) Sealing wire(3) Low- and high-speed(4) Governor spring(5) Sliding shaft(6) Stopper(7) Governor spring(8) Governor shaft(9) Governor lever(10) Tie-rod(11) Tie-rod clip(12) Tie-rod cover(13) tie-rod cover gasket(14) Tension lever(15) Start spring(16) Governor spring lever(17) Speed control lever assembly(18) Cover assembly(19) Governor cover gasket(20) Return spring(21) Stop lever assembly(22) O-ring(23) Snap ring(24) Stop lever(25) Grooved pin (3 x 20)(26) Grooved pin (3 x 14)(27) Torque spring set(28) Sealing capTORQUE SPRING
Installation of Torque Spring Set
Install and adjust the torque spring set using the following procedure:(1) Set the speed control lever to the high-idling speed position by adjusting the high-speed set bolt.(2) Turn in the torque spring set until engine speed drops about 50 rpm from high-idling speed.(3) From this position, turn back the torque spring set by the specified number of turns (N.) Lock the torque spring set at that position with the special nut.(4) Install the torque spring set sealing cap and stake the cap to prevent loosening. CAUTION There are two types of torque spring set: The single spring type and the double-spring type. Since each torque spring set has been adjusted precisely during assembly, do not tamper with the adjust screw unless it is necessary.
Torque spring setAssembling the Torque Spring Set
When the torque spring set has been disassembled or its component parts have been replaced, reassemble and adjust the torque spring set using the following procedure:
Assembling torque spring setSingle spring type
When installing the single-spring type torque spring set, use the following steps.(1) Lightly turn in adjust screw (5) (with a screw-driver operated by fingertips) until a resistance to screw rotation is felt. Lightly lock the screw at that position with locknut (4).(2) Set the scale to the zero-point. Turn in the spring case (2) until the value of load "A" shown in table below can be attained. Lock the spring case at that position with special nut (3).(3) Temporarily loosen adjust screw (5) until the value of load "A" is reduced by about 200 grams, and then retighten the screw until the value of "B" is attained. Lock the screw at that position with locknut (4).Adjust screw tightening torque: 0.8 to 1.2 kg.(4) To inspect the torque spring set for properly adjusted spring load, use a testing arrangement such as shown in the figure at right. Gradually push the scale against the torque spring set until the stopper (1) is moved (or the pointer of dial gauge deflects). Check that the load applied to the torque spring at that moment coincides with the value of load "C".
Setting of Torque Spring CHECKING
Replace the gear case and inspect the governor. When removing the gear case, be sure to remove the tie-rod cover by the side of the fuel pump and disconnect the tie-rod from the rack.If any parts are found defective, replace them.
Inspecting Torque Spring CAUTION When the governor is assumed to be malfunctioning, check the bearing on the gear case side, too.
Inspection Governor System PartsRemoval and Installation
(Refer to I-06 GEAR CASE AND OIL PUMP.)Removal(1) Removing the levers(a) to remove the levers, pull out the grooved pins which have been driven into the governor lever, stop lever, and speed control lever.(b) Loosen bolts fastening the levers and shafts.(2) InstallationInstall the levers and shafts, one after another, checking for proper function of them.
Installing Speed Control Lever CAUTION1. After press-fitting each grooved pin, check the shaft for smooth rotation.2. Coat the O-rings with oil before installing them.3. No deflection exceeding 20 mm is permitted for the governor spring installed.4. Install the governor spring lever and speed control lever so that play of angle between levers (standard: 5°) is minimized.